NEWCOM, INC.

56KIFXSP (A)

Card Type                    Modem (asynchronous)
Chip Set                     Unidentified
I/O Options                  Microphone, speaker/line out
Maximum Modem Rate           56Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation Protocol     Bell 103A/212A

                             V.34, V.32bis, V.32, V.23, V.22bis, V.22,
                             V.21, K56flex, V.90
Fax Modulation Protocol      V.17, V.29, V.27ter, V.21CH2
Error Correction/Compression V.42, MNP10, V.42bis, MNP5
Fax Class                    Class I & II
Data Bus                     16-bit ISA

[Image]

                                CONNECTIONS

        Function           Label             Function              Label

  Wake on ring                 CN1      Line out                    CN5

  Microphone - internal        CN2      Microphone - external       CN6

  TAD (sound card)             CN3      Speaker/line out            CN7
  connector

  Line in                      CN4

                   SUPPORTED COMMAND SET

                     Basic AT Commands

  AT, A/

  A, C, E, H, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &J, &L, &M, &P, &Q, &R, &T, &V, &W, &X, &Y, &Z

                   Extended AT Commands

  \A, \B, \G, \K, \L, \N

  %C, %Q

                        S-Registers

  A list of S-registers was unavailable

  Note: See MHI Help File for full command documentation.











                         Proprietary AT Command Set

                          COMMUNICATION PROTOCOLS

  Type:                  Configuration

  Format:                AT [cmds] Bn [cmds]

  Description:           Selects the communication protocol for data
                         calls

            Note: The B command allows the simultaneous selection of more
            than one suffix, enabling multiple protocols.

        Command                              Protocol

          B0             ITU-T V.22 at 300 or 1200bps

          B1             Bell 212A at 300 or 1200bps

          B15            V.21 connection at 300bps

          B16            Bell 103 connection at 300bps

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#> [cmds]

  Description:           Dials telephone number according to any
                         modifiers included in the string

  Note:                  Any combination of modifiers can be used to
                         produce the desired dial functions in sequence.

        Command                              Function

          DL             Re-dial last number

          DP             Pulse dialing enabled

          DR             Answer mode enabled; originate mode disabled
                         following handshake initiation.

         DS=n            Dial stored telephone number n

          DT             Tone dialing enabled/Pulse dialing disabled

          DW             Dialing resumed following dial tone detection

          D,             Dialing paused for amount of time specified in
                         S8 register

          D!             Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

          D@             Wait for Quite Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

          D^             Turns on the periodic 1300Hz calling tone.

          D;             Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.























                              LINE MODULATION

  Type:          Configuration

  Format:        AT [cmds] Fn [cmds]

  Description:   Selects line modulation

            Note: This command is only supported on older modems

    Command                              Function

       F0        Auto-detect mode

       F1        V.21 or Bell 103

       F3        V.23

       F4        V.22 or Bell 212A @ 1200bps

       F5        V.22bis

       F6        V.32bis or V.32 @ 4800bps

       F7        V.32bis @ 7200bps

       F8        V.32bis for V.32 @ 9600bps

       F9        V.32bis @ 12000bps

      F10        V.32bis @ 14400bps

                            REPORT INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested

    Command                              Function

       I0        Reports product code

       I1        Reports ROM checksum

       I2        Tests and reports ROM checksum

       I3        Reports firmware revision level

       I4        Reports product capabilities

       I5        Reports country code

       I6        Reports modem data pump control

                              SPEAKER VOLUME

  Type:          Configuration

  Format:        AT [cmds] Ln [cmds]

  Description:   Controls speaker volume

    Command                              Function

       L0        Low volume setting

       L1        Low volume setting

       L2        Medium volume setting

       L3        Highest volume setting

                          FACTORY DEFAULT PROFILE

  Type:             Configuration

  Format:           AT [cmds] &F [cmds]

  Description:      Sets values in active profile to values found in the
                    default profile

     Command                              Function

       &F0          Restore factory profile 0

       &F1          Restore factory profile 1

                                GUARD TONE

  Type:           Configuration

  Format:         AT [cmds] &Gn [cmds]

  Description:    Commands the modem to transmit a guard tone in
                  V.22/V.22bis

            Note: Used primarily for international data transmission

    Command                              Function

      &G0         Guard tone disabled

      &G1         Guard tone disabled

      &G2         1800Hz guard tone enabled

                               FLOW CONTROL

  Type:          Configuration

  Format:        AT [cmds] &Kn [cmds]

  Description:   Enables flow control options

    Command                              Function

      &K0        Flow control disabled

      &K3        RTS/CTS flow control enabled

      &K4        XON/XOFF flow control enabled

      &K5        Transparent XON/XOFF flow control enabled

      &K6        RTS/CTS, XON/XOFF, and DTE/DCE flow control enabled

                           DATA SET READY (DSR)

  Type:          Configuration

  Format:        AT [cmds] &Sn [cmds]

  Description:   Selects DSR options

    Command                              Function

      &S0        DSR forced high

      &S1        DSR high only while modem is handshaking or connected

                            Extended AT Commands

                 AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

  Type:          Configuration

  Format:        AT [cmds] %En [cmds]

  Description:   Controls auto-retrain mode and fallback/fall-forward

    Command                              Function

      %E0        Auto-retrain disabled

      %E1        Auto-retrain enabled