HARMONY MULTIMEDIA HM 18008-5 Card Type Modem (asynchronous) Chip Set Unidentified I/O Options Microphone, headphone, speaker out, line in, line out Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.34+, V.34, V.32bis, V.32, V.22bis, V.22A/B, V.23, V.21, Fax Modulation Protocol ITU-T V.17, V.29, V.27ter, V.21CH 2 Error Correction/Compression V.42, V.42bis, MNP5 Fax Class Class I Data Bus 16-bit ISA Card Size Half-length, full-height card [Image] CONNECTIONS Function Label Function Label Line in CN1 Headphone CN4 Line out CN2 Speaker out CN5 Microphone CN3 SERIAL PORT ADDRESS Setting JP1/A JP1/B JP1/C JP1/D COM1 (3F8h) Open Open Closed Closed COM2 (2F8h) Closed Open Open Closed COM3 (3E8h) Open Closed Closed Open COM4 (2E8h) Closed Closed Open Open INTERRUPT Setting JP1/E JP1/F JP1/G JP1/H JP1/I JP1/J JP1/K JP1/L JP1/M JP1/N IRQ 3 Closed Open Open Open Open Open Open Open Open Open IRQ 4 Open Closed Open Open Open Open Open Open Open Open IRQ 5 Open Open Closed Open Open Open Open Open Open Open IRQ 7 Open Open Open Closed Open Open Open Open Open Open IRQ 10 Open Open Open Open Open Open Closed Open Open Open IRQ 11 Open Open Open Open Open Closed Open Open Open Open IRQ 12 Open Open Open Open Closed Open Open Open Open Open PnP Closed Closed Closed Closed Closed Closed Closed Closed Closed Closed SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, C, D, E, F, H, M, O, P, Q, T, V, X, Y, Z &C, &F, &G, &T, &W, &Y, &Z Extended AT Commands \A, \B, \C, \G, \J, \K, \O, \U, \X, \Y, \Z %A, S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S24, S25, S26, S29, S38, S39, S46, S48, S82, S86, S90, S91, S92, S95, S99, S108, S109, S110, 201 Special Commands "H, -J Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Handshake only at DTE- to-modem data rate N1 Begins handshake DTE-to-modem rate at highest compatible rate AUXILIARY RELAY Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Sets the auxiliary relay function Command Function &J0 Auxiliary relay never operated &J1 Activates auxiliary relay when modem is off-hook COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode (modem supports asynchronous mode only) COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Asynchronous mode (modem supports asynchronous mode only.) COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 ITU-T V.22 at 300 or 1200bps B1 Bell 212A at 300 or 1200bps B2 ITU-T V.23 at 75 or 1200bps B3 ITU-T V.22 at 1200 or 75bps CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles Command Function &V0 View stored profile 0 &V1 View stored profile 1 &V2 View relay and general-purpose I/O status DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] Wn [cmds] Description: Enables selection of additional result codes when S95=0; otherwise, S95 takes precedence. Command Function W0 DTE speed response codes W1 DTE speed response codes W2 DCE speed response codes W3 DTE speed response codes with error correct and data compression W4 Reports protocol , data compression, and DTE data rate FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 Bi-directional hardware flow control &K4 XON/XOFF flow control enabled PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports modem chip firmware version I2 Tests and reports ROM checksum I3 Reports chipset name I4 Reserved I5 Reserved for modem chip hardware configuration I6 Reports country code I7 Reports version of board manufacturer firmware I8 Reports features of modem firmware I10 Reports modem board configuration-bits set by board manufacturer I11 Reports modem board configuration-bits set by board manufacturer I14 Reports SAFE device I20 Reports chip manufacturer’s silicon version I21 Reports chip manufacturer’s firmware version I22 Reports chip manufacturer’s name I23 Reports chip manufacturer’s product model SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TRELLIS CODING Type: Immediate Format: AT [cmds] &u [cmds] Description: Controls Trellis coding Command Function &U0 Enable Trellis coding with QAM as fallback &U1 QAM modulation only Extended AT Command Set AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %Gn [cmds] Description: Selects auto-fallback/fall-forward Command Function %G0 Auto-fallback/fall-forward disabled %G1 Generate data modem calling tone AUTO-RETRAIN Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 MNP5 enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Normal mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled DATA MODEM CALLING TONE Type: Configuration Format: AT [cmds] -Cn [cmds] Description: Sets the data modem calling tone Command Function -C0 Calling tone disabled -C1 1300-Hz calling tone enabled -C2 V.8 calling tone and 1300-Hz calling tone FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 XON/XOFF flow control enabled \Q2 Uni-directional hardware flow control enabled \Q3 Bidirectional hardware flow control enabled INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0-90 Unit: 1 second Description: Sets the length of time that the modem does not receive information before it disconnects. V.42bis - MAXIMUM STRING LENGTH Type: Immediate Format: AT [cmds] "On [cmds] Default: 32 Range: 6-250 Unit: Characters Description: Selects string size for V.42bis compression AT# VOICE COMMAND SET BEEP TONE Format: AT [cmds] +VTD=n [cmds] Default: 100 Range: 5-255 Description: Sets the beep tone duration timer BUFFER THRESHOLD Type: Immediate Format: AT [cmds] +VBT=n [cmds] Default: 192, 320 Range: 192, 320 Description: Sets the buffer threshold CALLER ID Format: AT [cmds] +VCID=n [cmds] Default: 0 Range: 0-2 Description: Sets the caller ID COMPRESSION METHOD Format: AT [cmds] +VSM=n [cmds] Default: 140 (8-bit cirrus A-law) 8000 (used by some BBS) 0 (transmission disabled) 0 (DCE disabled) Description: Sets the compression method FLOW CONTROL SELECT Type: Immediate Format: AT [cmds] +FLO=n [cmds] Default: 1 Range: 0-2 Description: Selects the flow control HANG-UP CONTROL Format: AT [cmds] +VNH=n [cmds] Default: 0 Range: 0-2 Description: Controls the automatic hang-up INACTIVITY TIMER Format: AT [cmds] +VIT=n [cmds] Default: 0 Range: 0-255 Description: Sets the DTE/DEC inactivity timer INITIALIZE PARAMETER Format: AT [cmds] +VIP [cmds] Description: Initialize parameter SILENCE DETECTION Format: AT [cmds] +VCSD=n [cmds] Default: 0 Range: 0, 1 Description: Sets the voice command mode silence detection DISTINCTIVE RING Format: AT [cmds] +VDR=n [cmds] Default: 0, 0 Range: 0-255, 0-255 Description: Sets the distinctive ring MICROPHONE GAIN Format: AT [cmds] +VGM=n [cmds] Default: 128 Range: 121-131 Description: Sets the microphone gain PLAY MODE Format: AT [cmds] +VTX [cmds] Description: Sets the play mode RECEIVE GAIN Format: AT [cmds] +VGR=n [cmds] Default: 128 Range: 121-131 Description: Sets the receive gain RECORD MODE Format: AT [cmds] +VRX [cmds] Description: Sets the record mode RELAY/SPEAKER CONTROL Format: AT [cmds] +VGS=n [cmds] Default: 0 Range: 0-16 Description: Stes the relay/speaker control REPORTING AND MASKING Format: AT [cmds] +VEM=n [cmds] Default: ‘C’, BB860980, BFE63883, BB863EE0 Description: Controls the event reporting and masking RINGBACK TIMER Format: AT [cmds] +VRA=n [cmds] Default: 50 Range: 0-50 Description: Sets the ringback-goes-away timer RINGBACK TIMER Format: AT [cmds] +VRN=n [cmds] Default: 10 Range: 0-255 Description: Sets the ringback-never-appeared timer SILENCE DETECTION Format: AT [cmds] +VSD=n [cmds] Default: 128 (nominal) 50 (silence detection enabled) Description: Sets silence detection VOICE MODE SELECTION Type: Immediate Format: AT [cmds] +FCLASS=n [cmds] Default: 0 Range: 0, 1, 8, 80 Description: Sets the voice mode VOLUME SELECTION Format: AT [cmds] +VGT=n [cmds] Default: 128 Range: 121-131 Description: Selects the volume SPEAKERPHONE SELECTION Format: AT [cmds] +VSP=n [cmds] Default: 0 Range: 0, 1 Description: Controls the speakerphone SPEAKER PHONE TYPE Format: AT [cmds] #VSPS=n [cmds] Default: 0 Range: 0, 1 Description: Sets the speakerphone type TONE GENERATION Format: AT [cmds] +VTS=n [cmds] Description: Sets the DTMF and tone generation