MAXTECH CORPORATION XPV 336IC (SF-1133HV/C3) Card Type Modem/Fax card Chip Set Unidentified I/O Options Line in(RJ-11), line out(RJ-11), microphone jack, speaker jack Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V34, V34+, V.FC Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA [Image] CONNECTIONS Function Label Function Label RJ-11 line CN1 Microphone CN3 RJ-11 line CN2 Speaker CN4 USER CONFIGURABLE SETTINGS Setting Label Position Stereo speaker configuration enabled JP5 Closed Mono speaker configuration enabled JP5 Open SERIAL PORT ADDRESS Setting S1/A S1/B S1/C S1/D COM1 (3F8h) Open Open Closed Closed COM2 (2F8h) Closed Open Open Closed COM3 (3E8h) Open Closed Closed Open COM4 (2E8h) Closed Closed Open Open Plug & Play Open Open Open Open enabled INTERRUPT Setting S2/A S2/B S2/C S2/D S2/E S2/F S2/G IRQ3 Closed Open Open Open Open Open Open IRQ4 Open Closed Open Open Open Open Open IRQ5 Open Open Closed Open Open Open Open IRQ7 Open Open Open Closed Open Open Open IRQ10 Open Open Open Open Closed Open Open IRQ11 Open Open Open Open Open Closed Open IRQ12 Open Open Open Open Open Open Closed Plug & Closed Closed Closed Closed Closed Closed Closed Play enabled SUPPORTED COMMAND SET Basic AT Commands AT, +++, A/ A, E, H, M, O, P, Q, T, V, X, Y, Z &C, &F, &G, &W, &Y, &Z Extended AT Commands \A, \B, \C, \G, \J, \K, \O, \U, \X, \Y, \Z %A, %G -J "H S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S27, S30, S31, S33, S37 Special Commands +MS Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 When originating or answering; handshake only at DTE to modem rate N1 When originating or answering; handshake at DTE to modem rate. Modem can shift to a lower speed if necessary AUXILIARY RELAY Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Enables/disables auxiliary relay Command Jack Type &J0 Auxiliary relay disabled &J1 Auxiliary relay enabled when modem is off-hook COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 CCITT mode B1 Bell 212A at 300 or 1200bps B2 V.23 at 1200bps transmit, 75bps receive B3 V.23 at 75bps transmit, 1200bps receive COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Asynchronous mode, serial port speed follows connect speed. CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &Vn [cmds] Description: Displays active and stored configuration profiles Command Function &V0 Displays active and stored configuration profile 0 &V1 Displays active and stored configuration profile 1 DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR override &D1 DTR toggle causes online command mode &D2 Normal DTR operations &D3 Resets on receipt of DTR DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] Wn [cmds] Description: Enables selection of additional result codes. Command Function W0 Modem reports DTE response codes W1 Modem reports DTE response codes W2 Modem reports DCE response codes W3 Modem reports DTE speed, modulation mode, error control, data compression, DCE speed W4 Modem reports DTE protocol, data compression, and DTE speed FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports four digit product code I1 Reports ROM checksum I2 Reports internal memory test I3 Reports device ID I4 Reports internal ID I5 Reports modem chip hardware configuration I6 Reports country code I7 Reports manufacturer firmware version I8 Reports modem firmware version I10 Reports modem board configuration SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 End current test &T1 Begin local analog loopback test &T4 Grant remote digital loopback request &T5 Deny remote digital loopback request &T6 Request remote digital loopback &T7 Request remote digital loopback and self-test &T8 Begin local analog loopback and self-test TRELLIS CODING Type: Configuration Format: AT [cmds] &Un [cmds] Description: Enables/disables trellis coding Command Function &U0 V.32 trellis coding enabled &U1 V.32 trellis coding disabled EXTENDED AT COMMAND SET AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled CALLING TONE Type: Configuration Format: AT [cmds] -Cn [cmds] Description: Controls whether the DTE will allow the modem to send a 1300Hz calling tone when originating Command Function -C0 Calling tone disabled -C1 1300hz calling tone enabled -C2 V.8 and 1300hz calling tone enabled COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 MNP5 enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Normal mode enabled \N2 MNP mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bi-directional XON/XOFF flow control enabled \Q2 CTS flow control by DCE enabled \Q3 Bi-directional RTS/CTS flow control enabled INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Range: 0-90 Unit: 1 second Description: Sets the length of time that the modem does not receive information before it disconnects. V.42bis - MAXIMUM STRING LENGTH Type: Immediate Format: AT [cmds] "On [cmds] Range: 6-250 Unit: Characters Description: Selects string size for V.42bis compression. Default is 32. VIOCE AT COMMAND SET BUFFER THRESHOLD SELECTION Format AT [cmds] +VBT=n [cmds] Description: Sets buffer threshold CALLER ID SELECTION Format AT [cmds] +VCID=n [cmds] Description: Selects caller ID VOICE COMMAND MODE SILENCE DETECTION Format AT [cmds] #VCSD=n [cmds] Description: Detects voice command mode silence DISTINCTIVE RING SELECTION Format AT [cmds] +VDR=n [cmds] Description: Selects distinctive ring EVENT REPORTING AND MASKING Format AT [cmds] +VEM=n [cmds] Description: Reports and masks events SPEAKERPHONE MICROPHONE GAIN Format AT [cmds] +VGM=n [cmds] Description: Sets speakerphone microphone gain RECEIVE GAIN Format AT [cmds] +VGR=n [cmds] Description: Selects receive gain SPEAKERPHONE SPEAKER GAIN Format AT [cmds] +VGS=n [cmds] Description: Sets speakerphone speaker gain VOLUME SELECTION Format AT [cmds] +VGT=n [cmds] Description: Selects volume INITIALIZE PARAMETER Format AT [cmds] +VIP [cmds] Description: Sets voice initialization parameter INACTIVITY TIMER Format AT [cmds] +VIT=n [cmds] Description: Sets DTE/DCE inactivity timer RELAY/SPEAKER Format AT [cmds] +VLS=n [cmds] Description: Controls relay/speaker settings AUTOMATIC HANG-UP Format AT [cmds] +VNH=n [cmds] Description: Controls automatic hang-up option RINGBACK DROPPED Format AT [cmds] +VRA=n [cmds] Description: Determines amount of time before ringback is discontinued RINGBACK NOT RECIEVED Format AT [cmds] +VRN=n [cmds] Description: Sets time for ringback to not appear RECORD MODE Format AT [cmds] +VRX=n [cmds] Description: Determines record mode SILENCE DETECTION Format AT [cmds] +VSD=n [cmds] Description: Detects quiet and silence COMPRESSION METHOD Format AT [cmds] +VSM=n [cmds] Description: Selects compression method SPEAKERPHONE ENABLE Format AT [cmds] +VSP=n [cmds] Description: Controls on/off of speakerphone SPEAKERPHONE TYPE Format AT [cmds] #VSPS=n [cmds] Description: Selects speakerphone type BEEP TONE DURATION TIMER Format AT [cmds] +VTD=n [cmds] Description: Sets the beep tone duration timer DTMF AND TONE GENERATION Format AT [cmds] +VTS=n [cmds] Description: Controls DTMF and tone generation PLAY MODE Format AT [cmds] +VTX=n [cmds] Description: Sets play mode