CARDINAL TECHNOLOGIES, INC. MVP34ISP Card Type Modem/Fax card Chip Set Unidentified I/O Options Line in, line out, microphone jack, speaker jack Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V34, V.32bis, V.32, V.22bis, V.22, V.21 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29, V.21 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA [Image] CONNECTIONS Function Label Function Label RJ-11 line in CN1 Microphone jack CN3 RJ-11 line out CN2 Speaker jack CN4 SERIAL PORT ADDRESS Setting JP1/A JP1/B JP1/C JP1/D JP1/E JP1/F COM1 Closed Open Open Open Open Open (3F8h) COM2 Open Closed Open Open Open Open (2F8h) COM3 Open Open Closed Open Open Open (3E8h) COM4 Open Open Open Closed Open Open (2E8h) Plug & Open Open Open Open Closed Closed Play enabled INTERRUPT Setting JP2/A JP2/B JP2/C JP2/D JP2/E JP2/F IRQ3 Open Open Open Open Open Closed IRQ4 Open Open Open Open Closed Open IRQ5 Open Open Open Closed Open Open IRQ7 Open Open Closed Open Open Open IRQ10 Open Closed Open Open Open Open IRQ11 Closed Open Open Open Open Open Plug & Open Open Open Open Open Open Play enabled SUPPORTED COMMAND SET Basic AT Commands AT, +++, A/ A, B, E, H, M, O, P, Q, T, V, W, Y, Z &C, &G, &P, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \G, \K, \N, %C, %E, %L, %Q +MS #CID S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S29, S30, S31, S32, S33, S38, S39, S40, S41, S95 Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled; handshake begins at line speed designated by the S37 register. N1 Auto-mode detection enabled DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR override &D1 DTR toggle causes online command mode &D2 Normal DTR operations &D3 Resets on receipt of DTR DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D"WXY" Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. D* The star digit (touch tone only) D# The gate digit (touch tone only) D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D/ Delays 125 ms. Before proceeding with dial string D^ Calling tone enable/disable for current call only D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D& Waiting for AT&T "bong" tone FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables/disables flow control Command Line Type &K0 Flow control disabled &K3 Hardware, RTS/CTS flow control enabled &K4 Software, XON/XOFF flow control enabled &K5 Transparent software, XON/XOFF flow control enabled &K6 Software & hardware flow control enabled Note: Default setting for fax operations is &K6 REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports four digit product code I1 Reports firmware checksum I2 Verify checksum I3 Reports firmware revision I4 Reports identifier string I5 Reports country code I6 Reports data pump modem and revision SELECT CALL PROGRESS RESULT CODES Type: Configuration Format: AT [cmds] Xn [cmds] Description: Enables selection of tone detection and associated result code format options Command Function X0 Busy and dial tone detection disabled; extended result codes diabled. X1 Busy and dial tone detection disabled; extended result codes enabled. X2 Busy tone detection disabled, dial tone detection enabled; extended result codes enabled. X3 Busy tone detection enabled, dial tone detection disabled; extended result codes enabled. X4 Busy and dial tone detection enabled; extended result codes enabled. SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting AT VOICE COMMAND SET AUDIO MODULATION Type: Configuration Format: AT [cmds] -SQS=x,y [cmds] Description: Selects data speed with audio modulation; enable/disable automode Command Function x=0 V.61 modulation enabled (4800bps) x=1 V61+ modulation enabled (4800bps - 9600bps) x=2 V34Q modulation enabled (4800bps - 14.4Kbps) y=0 Automode disabled y=1 Automode enabled AUDIOSPAN MODE Type: Configuration Format: AT [cmds] -SMS=x,y,z [cmds] Description: Selects audiospan modem; selects voice and data speed Command Function x=0 Audiospan disabled/data only x=1 Reserved x=2 Audiospan enabled y=4800 Minimum voice+data speed set to 4800bps y=7200 Minimum voice+data speed set to 7200bps y=9600 Minimum voice+data speed set to 9600bps y=12000 Minimum voice+data speed set to 12.0Kbps y=14400 Minimum voice+data speed set to 14.4Kbps z=4800 Maximum voice+data speed set to 4800bps z=7200 Maximum voice+data speed set to 7200bps z=9600 Maximum voice+data speed set to 9600bps z=12000 Maximum voice+data speed set to 12.0Kbps z=14400 Maximum voice+data speed set to 14.4Kbps DATA BURST Type: Configuration Format: AT [cmds] -SMCn [cmds] Description: Data burst enable/disable. Command Function SMC0 Data burst disabled; audio channel open at all times during connection SMC1 Data burst enabled; audio channel open only when data is detected on network DISTINCTIVE RING Format: AT [cmds] -SDR=n [cmds] Default: Unidentified Range: 0 - 255 Description: Selects which distinctive ring signals the modem will respond to. Bit Value Function 0 0 Distinctive ring disabled 1 0 Distinctive ring type 1 disabled. 1 Distinctive ring type 1enabled. 2 0 Distinctive ring type 2disabled 1 Distinctive ring type 2 enabled. 3 0 Distinctive ring types 1 & 2 disabled. 1 Distinctive ring types 1 & 2 enabled. 4 0 Distinctive ring type 3 disabled. 1 Distinctive ring type 3 enabled. 5 0 Distinctive ring types 1 & 3 disabled. 1 Distinctive ring types 1 & 3 enabled. 6 0 Distinctive ring types 2 & 3 disabled. 1 Distinctive ring types 2 & 3 enabled. 7 0 Distinctive ring types 1, 2 & 3 disabled. 1 Distinctive ring types 1, 2 & 3 enabled. MNP10EC Type: Configuration Format: AT [cmds] -SECn, [] [cmds] Range (tx level) 0-30dBm Description: Enable/disable MNP10EC Command Function -SEC0 MNP10EC disabled -SEC1 [] MNP10EC enabled. The transmission level will be defined by VOICE DEVICE Type: Configuration Format: AT [cmds] #VLS=n [cmds] Description: Selects the I/O device for the DSP chip. Command Function #VLS=0 Telephone line and handset used for voice I/O. #VLS=1 Speakerphone used for voice I/O. S(STATUS) -REGISTERS CONNECTION FAILURE CODES Type: Register Format AT [cmds] S86? [cmds] Description: Reports codes which correspond to the possible causes of a connection failure Value Meaning 00 Normal hang up 04 Carrier signal lost 05 V.42 negotiation failed to detect an EC modem 09 No common protocol found 12 No failure - remote modem disconnected normally 13 Remote modem failed to respond after 10 re-transmissions same message 14 Violation of negotiated protocol caused failure DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Speed of last connection S37=1 Reserved S37=2 Reserved S37=3 300bps S37=4 Reserved S37=5 1200bps, V.22 S37=6 2400bps, V.22bis S37=7 1200/75bps, V.23 S37=8 4800bps, V.32bis/V.32 S37=9 9600bps, V.32bis/V.32 S37=10 12.0Kbps, V.32bis S37=11 14.4Kbps, V.32bis S37=12 7200bps, V.32bis ERROR CORRECTION/COMPRESSION Type: Register Format: AT [cmds] S46=n [cmds] Description: Selects active error correction and compression protocols Command Function S46=136 LAP-M only, no compression S46=138 LAP-M with V.42bis data compression ERROR CORRECTION NEGOTIATION Type: Register Format AT [cmds] S36=n [cmds] Description: Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q. Command Function S36=0 Hang up S36=1 Attempt a direct connection S36=3 Attempt a buffered connection S36=4 Attempt a connection at MNP2-4; if that fails, hang up. S36=5 Attempt a connection at MNP2-4; if that fails, attempt a direct connection. S36=6 Reserved S36=7 Attempt a connection at MNP2-4; if that fails, attempt a buffered connection. FEATURE NEGOTIATION OPTIONS Type: Register Format: AT [cmds] S48=n [cmds] Description: Selects active error correction and compression protocols Command Function S48=0 Detection negotiation disabled, XID negotiation disabled S48=7 Fall-back to options set in S36