MAXTECH CORPORATION XPVS 56IC (X2/CL) Card Type Modem (asynchronous), fax Chip Set Unidentified I/O Options Microphone, speaker out, line in, line out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.34+, Std. X2 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA Card Size Half-length, half-height card [Image] CONNECTIONS Function Label Function Label Line out CN1 Microphone CN3 Line in CN2 Speaker out CN4 SERIAL PORT ADDRESS Setting JP1/A JP1/B JP1/C JP1/D COM1 (3F8h) Open Open Closed Closed COM2 (2F8h) Closed Open Open Closed COM3 (3E8h) Open Closed Closed Open COM4 (2E8h) Closed Closed Open Open PnP Open Open Open Open INTERRUPT IRQ JP1/E JP1/F JP1/G JP1/H JP1/I JP1/J JP1/K JP1/L JP1/M JP1/N 3 Closed Open Open Open Open Open Open Open Open Open 4 Open Closed Open Open Open Open Open Open Open Open 5 Open Open Closed Open Open Open Open Open Open Open 7 Open Open Open Closed Open Open Open Open Open Open 10 Open Open Open Open Closed Open Open Open Open Open 11 Open Open Open Open Open Closed Open Open Open Open 12 Open Open Open Open Open Open Closed Open Open Open PnP Closed Closed Closed Closed Closed Closed Closed Closed Closed Closed SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, O, P, Q, T, V, X, Y, Z &C, &F, &G, &T, &W, &Y, &Z Extended AT Commands \A, \B, \C, \G, \J, \K, \O, \U, \X, \Y, \Z %A, %E S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S21, S22, S23, S25, S27, S30, S37 Special AT commands +MS, -J, "H, "O Note: See MHI Help File for full command documentation. Proprietary AT Command Set COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for data calls Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. Command Protocol B0 CCITT mode B1 Bell mode B2 V.23 at 1200/75 B3 V.23 at 75/1200 DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports device ID I4 Reports internal ID I5 Reports modem chip hardware configuration I6 Reports country code I7 Reports manufacturer and model information I8 Reports modem firmware version I10 Reports modem board configuration SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Connect only at DTE rate N1 Automatic rate negotiation EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] Wn [cmds] Description: Enables selection of additional result codes when S95=0; otherwise, S95 takes precedence. Command Function W0 Enables CONNECT result codes to report DTE speed. W1 Enables CONNECT result codes to report DTE speed. W2 Enables CONNECT result codes to report DCE speed. W3 Enables CONNECT result codes to report DTE speed, modulation mode, error control, data compression, DCE transmit and receive speed DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off AUXILIARY RELAY Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Activates auxiliary relay Command Jack Type &J0 Auxiliary relay never operated &J1 Activates auxiliary relay when modem is off-hook FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 Enable hardware flow control &K4 Enable software flow control COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Asynchronous mode DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR is off in command mode, on in on-line mode TRELLIS CODING Type: Immediate Format: AT [cmds] &U [cmds] Description: Enables trellis coding Command Function &U0 Enable trellis coding @ V.32 &U1 Disable trellis coding @ V.32 CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles Command Function &V0 Displays the active profile to stored profile 0 &V1 Displays the active profile to stored profile 1 &V3 Displays the relay and general-purpose I/O satus Extended AT Command Set AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %Gn [cmds] Description: Selects auto-fallback/fall-forward Command Function %G0 Auto-fallback/fall-forward enabled %G1 Auto-fallback/fall-forward disabled AUTO_RELIABLE FALLBACK Type: Configuration Format: AT [cmds] %An [cmds] Description: Set auto-reliable fallback character to n (n=0-127) (requires the \C2 setting) Command Function -C0 Calling tone disabled -C1 1300hz calling tone -C2 V.8 and 1300hz calling tones enabled CALLING TONE Type: Configuration Format: AT [cmds] -C [cmds] Description: Controls calling tone Command Function -C0 Calling tone disabled -C1 1300hz calling tone -C2 V.8 and 1300hz calling tones enabled MNP CLASS 5 DATA COMPRESSION Type: Configuration Format: AT [cmds] %C [cmds] Description: Controls the MNP class 5 data compression Command Function %C0 Disable MNP class 5 data compression %C1 Enable MNP class 5 data compression CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Normal mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 XON/XOFF software flow control enabled \Q2 CTS flow control by DCE enabled \Q3 RTS/CTS hardware flow control enabled INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0-90 Unit: 1 second Description: Sets the length of time that the modem does not receive information before it disconnects. S(status) -REGISTERS SLEEP TIMER Type: Register Format AT [cmds] S33=n [cmds] Default: Unidentified Range: 0-255 Unit: Unidentified Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. STANDARD AT# VOICE COMMAND SET VOICE MODEM SELECT Type: Immediate Format: AT [cmds] +FCLASS=8 [cmds] Description: Select voice modem FLOW CONTROL Type: Immediate Format: AT [cmds] +FLO [cmds] Description: Flow control select TONE GENERATOR LENGTH Format AT [cmds] +VBT=n [cmds] Default: 10 Range: 0 - 40 Unit: 0.1 second Description: Sets the length of DTMF tones that are generated. CALLED ID Type: Immediate Format: AT [cmds] +VCID=n [cmds] Description: Called ID selection VOICE COMMAND Type: Immediate Format: AT [cmds] +VCSD=n [cmds] Description: Voice command mode silence detection DISTINCTIVE RING Type: Immediate Format: AT [cmds] +VDR=n [cmds] Description: Distinctive ring selection EVENT REPORTING Type: Immediate Format: AT [cmds] +VEM=n [cmds] Description: Event reporting and masking GAIN Type: Immediate Format: AT [cmds] +VGM=n [cmds] Description: Speakerphone microphone gain GAIN Type: Immediate Format: AT [cmds] +VGR=n [cmds] Description: Receive gain GAIN Type: Immediate Format: AT [cmds] +VGS=n [cmds] Description: Speakerphone speaker gain VOICE VOLUME LEVEL Type: Configuration Format: AT [cmds] +VGT=n [cmds] Description: Sets the volume level when playing back audio signals. INITIALIZE PARAMETER Type: Immediate Format: AT [cmds] +VIP [cmds] Description: Initialize parameter INACTIVITY TIMER Type: Immediate Format: AT [cmds] +VIT=n [cmds] Description: DTE/DCE inactivity timer VOICE DEVICE Type: Configuration Format: AT [cmds] +VLS=n [cmds] Description: Selects the I/O device for the DSP chip. Note: This modem may not support all options listed below. The #VLS? command will display the available options. Command Function +VLS=0 Telephone line and handset used for voice I/O. +VLS=1 Telephone handset used for voice I/O. +VLS=2 Internal speaker only used for voice I/O. +VLS=3 External microphone only used for voice I/O. +VLS=4 Telephone line and handset used for voice I/O; internal speaker enabled. +VLS=5 Headset used for voice I/O. +VLS=6 Speakerphone used for voice I/O. +VLS=7 Handset muted by disconnecting handset or speakerphone from telephone line. +VLS=8 Connects caller ID relay for recording of conversation over handset. +VLS=9 Connects handset (or speakerphone) to DSP chip for recording or playback. AUTO HANG-UP Type: Immediate Format: AT [cmds] +VNH=n [cmds] Description: Automatic hang-up control VOICE RE-RING DETECT TIME Type: Configuration Format: AT [cmds] +VRA=n [cmds] Default: 70 Range: 0-255 Unit: 10 mS Description: Sets the maximum time the modem will wait for the remote station to ring again before it assumes that it has gone off-hook. VOICE RING DETECT TIME Type: Configuration Format: AT [cmds] +VRN=n [cmds] Default: Unidentified Range: Unidentified Unit: Unidentified Description: Sets the maximum time the modem will wait for the remote station to ring before it assumes that it went off-hook before it rang. VOICE RECEIVE Type: Immediate Format: AT [cmds] +VRX Description: Commands the modem to begin receiving voice data. SILENCE DETECTION Type: Immediate Format: AT [cmds] +VSD=n [cmds] Description: Silence detection (quiet and silence) COMPRESSION Type: Immediate Format: AT [cmds] +VSM=n [cmds] Description: Compression method selection SPEAKERPHONE CONTROL Type: Configuration Format: AT [cmds] +VSP=n [cmds] Default: Unidentified Range: 0 - 255 Unit: .1 second Description: Speakerphone on/off control TONE DETECTION Format: AT [cmds] +VTD=x,y,z [cmds] Default: x,y,z 63 Range: 0 - 63 Description: Sets which tones the tone detection will report. Note: The value of x sets the tone detection modes in voice transmit mode, y sets them in voice receive mode, and z sets them in voice command mode. Bit Value Function 0 0 DTMF tones are not detected. 1 DTMF tones are detected. 1 0 V.25 1300Hz calling tone is not detected. 1 V.25 1300Hz calling tone is detected. 2 0 T.30 1100Hz fax tone is not detected. 1 T.30 1100Hz fax tone is detected. 3 0 V.25/T.30 2100Hz answer tone is not detected. 1 V.25/T.30 2100Hz answer tone is detected. 4 0 Bell 2225Hz answer tone is not detected. 1 Bell 2225Hz answer tone is detected. 5 0 Call progress tones are not detected. 1 Call progress tones are detected. TONE GENERATOR - TIMED PHONE KEYS Type: Immediate Format: AT [cmds] +VTS={a, n} Range: a 0-9, A-D, #, *; x 0-255 Unit: x .1 second Description: Generates the DTMF tone for duration x for the character a. VOICE TRANSMIT Type: Immediate Format: AT [cmds] +VTX Description: Commands the modem to begin transmitting voice data.