MAXTECH CORPORATION XPVS 56IF (SF-1156HV/TX(X2)) Card Type Modem (asynchronous) Chip Set Unidentified I/O Options microphone, speaker out, line in, line out Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212 ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34+, x2 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42bis, V.42bis Fax Class Unidentified Data Bus 8-bit ISA Card Size Half-length, half-height card [Image] CONNECTIONS Function Label Function Label Line out CN1 Microphone CN4 Line in CN2 Speaker out CN3 USER CONFIGURABLE SETTINGS Setting Label Position Speaker type stereo JP5 Closed Speaker type mono JP5 Open SERIAL PORT ADDRESS Setting JP3/A JP3/B JP3/C COM1 (3F8h) Closed Closed Closed COM2 (2F8h) Open Closed Closed COM3 (3E8h) Closed Open Closed COM4 (2E8h) Open Open Closed PnP Open Open Open INTERRUPT SELECTION IRQ JP2/A JP2/B JP2/C JP2/D JP2/E 2/9 Closed Open Open Open Open 3 Open Closed Open Open Open 4 Open Open Closed Open Open 5 Open Open Open Closed Open 7 Open Open Open Open Closed PnP Open Open Open Open Open SUPPORTED COMMAND SET Basic AT Commands AT, +++, A/ A, B, E, F, H, M, O, P, T, V, X &C, &G, &T, &W, &Z S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25, S38 AT Voice Commands #VBQ?, #VBS, #VBT, #VCI, #VLS, #VRA, #VRN, #VRX, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX, #BDR, #CLS, #MDL, #MFR, #REV? Note: See MHI Help File for full command documentation. Proprietary AT Command Set DISPLAY COMMANDS Type: Configuration Format: AT [cmds] $ [cmds] Description: Displays the basic command set DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D/ Delays for 125msec. before dialing D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D$ Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports product ID I4 Reports current modem settings I5 Displays active and stored profiles I6 Reports data connection information I7 Reports manufacturer and model information SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Displays result codes only in Originate Mode CONFIGURATION PROFILE SELECT Type: Configuration Format: AT [cmds] Yn [cmds] Description: Commands the modem to use Profile 0 or Profile 1 Command Function Y0 Configuration Profile 0 active upon power on or reset Y1 Configuration Profile 1 active upon power on or reset SOFT RESET Type: Immediate Format: AT [cmds] Zn [cmds] Description: Restores modem profiles previously saved in non-volatile RAM using the &W command. Command Function Z0 Reset and retrieve active profile set by the Y command Z1 Reset and retrieve active profile 0 Z2 Reset and retrieve active profile 1 Z3 Reset and retrieve factory default profile 0 Z4 Reset and retrieve factory default profile 1 Z5 Reset and retrieve factory default profile 2 AUTO-ANSWER - ORIGINATE/ANSWER Type: Configuration Format: AT [cmds] &An [cmds] Description: Selects originate or answer mode when in Auto-Answer mode Command Function &A0 Disable ARQ result codes &A1 Enable ARQ result codes &A2 Disable ARQ result codes and V.32 modulation &A3 Enable ARQ result codes, V.32 modulation, error correction and data compression protocols DTE RATE ADJUST Type: Configuration Format: AT [cmds] &Bn [cmds] Description: Controls DTE rate Command Function &B0 DTE rate adjust to DCE rate after on line &B1 Constant DTE rate &B2 Constant DTE rate in ARQ mode, variable in non-ARQ mode DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile &F0 Recall factory default configuration 0 &F1 Recall factory default configuration profile 1 (hardware flow control enabled) &F2 Recall factory default configuration profile 2 (software flow control enabled) TX FLOW Type: Configuration Format: AT [cmds] &Hn [cmds] Description: Controls TX flow settings Note: Used primarily for international data transmission Command Function &H0 Disable TX flow controll &H1 Enable hardware TX flow control (CTS) &H2 Enable software TX flow control (XON/XOFF) &H3 Enable hardware (CTS) and software (XON/XOFF) TX flow control RX FLOW Type: Configuration Format: AT [cmds] &In [cmds] Description: Controls RX flow settings Note: Used primarily for international data transmission Command Function &I0 Disable software RX flow control &I1 Enable software RX flow control (XON/XOFF) &I2 Enable software RX flow control (XON/XOFF), but do not pass XON/XOFF to remote modem or local DTE &I3 Enable HP ENQ/ACK software flow control, host mode &I4 Enable HP ENQ/ACK software flow control, terminal mode &I5 Enable software RX flow control (XON/XOFF) for non-ARQ mode COMPRESSION CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables compression control options Command Function &K0 Disable V.42bis/MNP5 data compression &K1 Auto data compression &K2 Enable V.42bis/MNP5 data compression &K3 Disable MNP5 data compression COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Normal mode enabled &M4 ARQ and normal modes enabled &M5 ARQ mode enabled AUTOMODE CONNECTION SPEED Type: Configuration Format: AT [cmds] &Nn [cmds] Description: Selects connection speed Command Mode &N0 Enable Automode &N1 Set connection speed to 300bps &N2 Set connection speed to 1200bps &N3 Set connection speed to 2400bps &N4 Set connection speed to 4800bps &N5 Set connection speed to 7200bps &N6 Set connection speed to 9600bps &N7 Set connection speed to 12000bps &N8 Set connection speed to 14400bps &N9 Set connection speed to 16800bps &N10 Set connection speed to 19200bps &N11 Set connection speed to 21600bps &N12 Set connection speed to 24400bps &N13 Set connection speed to 26400bps &N14 Set connection speed to 28800bps &N15 Set connection speed to 31200bps &N16 Set connection speed to 33600bps &N17 Set connection speed to 33333bps &N18 Set connection speed to 37333bps &N19 Set connection speed to 41333bps &N20 Set connection speed to 42666bps &N21 Set connection speed to 44000bps &N22 Set connection speed to 45333bps &N23 Set connection speed to 46666bps &N24 Set connection speed to 48000bps &N25 Set connection speed to 49333bps &N26 Set connection speed to 50666bps &N27 Set connection speed to 52000bps &N28 Set connection speed to 53333bps &N29 Set connection speed to 54666bps &N30 Set connection speed to 56000bps &N31 Set connection speed to 57333bps PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 Reserved &R1 Modem ignores RTS signal &R2 Enable RX hardware flow control (RTS) DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR off in command mode, on in on-line mode MINIMUM DTE CONNECTION Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects minimum DTE connection speed Command Function &U0 Do not set minimum DCE connection speed &U1 Set connection speed to 300bps &U2 Set connection speed to 1200bps &U3 Set connection speed to 2400bps &U4 Set connection speed to 4800bps &U5 Set connection speed to 7200bps &U6 Set connection speed to 9600bps &U7 Set connection speed to 12000bps &U8 Set connection speed to 14400bps &U9 Set connection speed to 16800bps &U10 Set connection speed to 19200bps &U11 Set connection speed to 21600bps &U12 Set connection speed to 24400bps &U13 Set connection speed to 26400bps &U14 Set connection speed to 28800bps &U15 Set connection speed to 31200bps &U16 Set connection speed to 33600bps &U17 Set connection speed to 33333bps &U18 Set connection speed to 37333bps &U19 Set connection speed to 41333bps &U20 Set connection speed to 42666bps &U21 Set connection speed to 44000bps &U22 Set connection speed to 45333bps &U23 Set connection speed to 46666bps &U24 Set connection speed to 48000bps &U25 Set connection speed to 49333bps &U26 Set connection speed to 50666bps &U27 Set connection speed to 52000bps &U28 Set connection speed to 53333bps &U29 Set connection speed to 54666bps &U30 Set connection speed to 56000bps &U31 Set connection speed to 57333bps BREAK CONTROL Type: Configuration Format: AT [cmds] &Yn [cmds] Description: Controls the break Command Function &Y0 Destructive break. Does not send break &Y1 Destructive break. Break expedited &Y2 Nondestructive break. Break expedited S(status) -REGISTERS BUFFER RESET S13 Format: AT [cmds] S13=n [cmds] Unit: Bit-mapped Description: DTR, buffer reset, backspace, autodial. Retrain +++ hangup ARQ/MNP/V.42bis S15 Format: AT [cmds] S15=n [cmds] Unit: Bit-mapped Description: Disable ARQ/MNP/V.42bis INACTIVITY TIMER Type: Register Format AT [cmds] S19=n [cmds] Default: 0 Range: 0-255 Unit: 1 second Description: Sets the maximum duration for inactivity Note: S19=0 disables the timer and allows an indefinite duration. BIT-MAPPED REGISTER S21 Format AT [cmds] S21=n [cmds] Default: Unidentified Range: 0-253 Unit: 0.01sec Description: Sets the maximum duration for break FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S22=n [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S23=n [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF DTR CHANGE THRESHOLD Type: Register Format AT [cmds] S25=n [cmds] Default: 5 Range: 0-255 Unit: .1 second Description: Sets maximum time a change in the DTR signal will be ignored Note: This is the function of this register when &M1 is not set. BIT-MAPPED REGISTER S27 Type: Register Format AT [cmds] S27=n [cmds] Default: 5 Range: 0-255 Unit: Bit-mapped Description: V.21 @ 300bps, trellis coding, Disable V.32, answer tone, 9600 result codes, disable V.32bis, enable V.23 ANSWER TONE Format AT [cmds] S28=n [cmds] Default: 8 Range: 0-255 Unit: 0.1 second Description: Controls V.32 answer tone. ANSWER MODE TIMER Type: Register Format AT [cmds] S29=n [cmds] Default: 20 Range: 0-255 Unit: .01 second Description: Controls the V.21 answer mode timer. BIT-MAPPED REGISTER S32 Type: Register Format AT [cmds] S32=n [cmds] Unit: Bit-mapped Description: V8, V34, V34bis, x2 Enable V.8 BIT-MAPPED REGISTER S33 Format: AT [cmds] S33=n [cmds] Unit: Bit-mapped Description: Disable 2400, 2743, 2800, 3000, 3200, and 3429 symbol rates. BIT-MAPPED REGISTER S34 Format: AT [cmds] S34=n [cmds] Unit: Bit-mapped Description: Trellis coding :8S-2D, 16S-4D mapped register 32S-2D, 64S-4D BIT-MAPPED REGISTER S41 Format AT [cmds] S41=n [cmds] Default: Unidentified Unit: Bit-mapped Description: Distinctive ring (on=1)