MAXTECH CORPORATION XPVS 3361 (SF-1133HV/R12-PNP) Card Type Modem (Asynchronous) Chip Set Unidentified I/O Options line in, line out, microphone in, speaker out Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A, ITU-T V.34+, V.32bis, V.32, V.23, V.22bis, V.22, V.21 Fax Modulation Protocol V.17, V.27ter, V.29 Error Correction/Compression MNP5, V.42bis Fax Class Class I & II Data Bus 8-bit ISA Card Size Half-length, full-height card [Image] CONNECTIONS Function Label Function Label Line out CN1 Microphone in CN3 Line in CN2 Speaker out CN4 SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z &C, &F, &P, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \K, \N %C, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 Special Commands +MS, #CID Voice Commands #BDR, #CLS, #MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, VLS, #VRA, #VRN, VRX, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX Note: See MHI Help File for full command documentation. Proprietary AT Command Set DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D@ Wait for five seconds of silence D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D, Pause D; Return to the command mode after dialing DS=n Dial one of the four telephone numbers (n=0-3) stored in the modem’s non-volatile memory REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Reports internal memory test I6 Reports firmware ID I7 Reports reserved ID SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Autoscan mode disabled N1 Autoscan mode enabled DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Note: Used primarily for international data transmission Command Function &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800Hz guard tone enabled FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS to CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 Enable both RTS/CTS and XON/XOFF flow controll LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects line type Command Line Type &L0 Switched line (PSTN/Dial-up) COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Direct data link only &Q5 V.42 data link with fallback options &Q6 Normal data link only RTS/CTS Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS/CTS options Command Function &R0 Reserved &R1 CTS forced high, RTS is ignored DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only when modem is handshaking or connected EXTENDED AT COMMAND SET AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled