ACER, INC. MAGIC MP56 Card Type Modem (asynchronous), Fax, Sound card Chip Set Unidentified I/O Options CD-ROM interface, game port, wavetable interface, audio line in, audio line out, microphone Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation Protocol ITU-T V.17, V.33, V.29, V.27ter, V.21CH2 Error Correction/Compression MNP 5, V.42bis Fax Class Unidentified Data Bus 16-bit ISA [Image] CONNECTIONS Function Label Function Label Line out CN1 Wavetable interface CN6 Line in CN2 CD-ROM connector CN7 Microphone CN3 MIDI/Game port CN8 Audio line in CN4 Ring-on connector CN9 Speaker/audio line-out CN5 USER CONFIGURABLE SETTINGS Setting Label Position Flash download disabled JP4 Pins 1 & 2 closed Flash download enabled JP4 Pins 2 & 3 closed SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z &C, &F, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z Extended AT Commands \K, \N %E, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S95 Special Commands +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode detection enabled CLOCK SOURCE - SYNCHRONOUS TRANSMIT Type: Configuration Format: AT [cmds] &Xn [cmds] Description: Selects DTE transmit clock source Command Function &X0 Modem generates clock &X1 DTE generates clock DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR acts per V.25 DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q &Q Setting &D0 &D1 &D2 &D3 &Q0, &Q5, &Q6 Command 0 Command 1 Command 2 Command 3 &Q1, &Q4 Command 2 Command 1 Command 2 Command 3 &Q2, &Q3 Command 2 Command 2 Command 2 Command 2 Command Function Command 0 Modem does not respond to DTR Command 1 Modem goes to command mode after DTR goes is off Command 2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. Command 3 Modem is initialized after DTR goes off FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Disable DTE/DCE flow control &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 Unidirectional XON/XOFF flow control enabled GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Note: Used primarily for international data transmission Command Function &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800Hz guard tone enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Report firmware revision, model and interface type I4 Report response programmed by OEM I5 Report the country code parameter I6 Report modem data pump model and code revision SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TRANSMIT CARRIER Type: Configuration Format: AT [cmds] Cn [cmds] Description: Controls the transmit carrier switching S(status) -REGISTERS AUTO SYNCHRONIZATION OPTION Format AT [cmds] S19=n [cmds] Default: 0 Range: Unidentified Unit: Unidentified Description: Options are unidentified BIT-MAPPED REGISTER S20 Format AT [cmds] S20=n [cmds] Default: 0, Range: 0-253 Unit: Bit-mapped Description: Selects auto-sync HDLC address or BSC sync character