ACER, INC. MAGIC F34 Card Type Modem/Fax card Chip Set Unidentified Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation Protocol ITU-T V.17, V.33, V.29, V.27ter, V.21CH2 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 16-bit ISA Card Size Half length, full-height card [Image] CONNECTIONS Function Label Function Label Telephone line out CN1 Microphone CN4 Telephone line in CN2 Audio card connector CN5 Line out CN3 SERIAL PORT ADDRESS Setting JP2 JP3 JP4 JP5 COM1 1 & 2 2 & 3 2 & 3 2 & 3 COM2 2 & 3 1 & 2 2 & 3 1 & 2 Plug and Play enabled 1 & 2 Unidentified 1 & 2 1 & 2 Note: Pins designated should be in the closed position. To use the plug and play option, the optional chip C1 must be installed. SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, B, C, E, H, M, O, P, Q, T, V, W, X, Y, Z &C, &F, &M, &P, &Q, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \K, \N, \V, %C, %E, %L, %Q, %TT S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S19, S20, S21, S22, S23, S24, S25, S26, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 Special Commands #CID, +MS?, +MS, #BDR, #CLS, #MDL?, #MFR?, #REV?, #TL, #VBQ, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode detection enabled BLACKLISTED NUMBERS Type: Immediate Format: AT [cmds] *B [cmds] Description: Sends the list of ‘blacklisted’ numbers to the DTE. If no numbers are blacklisted, the OK result code is sent DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q &Q Setting &D0 &D1 &D2 &D3 &Q0, &Q5, &Q6 Command 0 Command 1 Command 2 Command 3 &Q1, &Q4 Command 4 Command 1 Command 2 Command 3 &Q2, &Q3 Command 2 Command 2 Command 2 Command 2 Command Function Command 0 Modem does not respond to DTR Command 1 Modem goes to command mode after DTR goes off Command 2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. Command 3 Modem is initialized after DTR goes off Command 4 Modem goes to command mode and disconnects (hangs up) after DTR goes off. DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function 0-9 Dialing digits A, B, C, D, *, # Tone dial characters P Pulse dial R Reverse originate mode S=n Dial NVRAM telephone number T Tone dial W Wait for dial tone , Pause ! Flash hook, modem goes on hook for .75 seconds @ Wait for quiet answer ^ Disable data calling tone for a single call origination ; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command -( ) space Ignored by modem. The modem ignores these characters, but they can be included in the dial string for separation purposes FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 Unidirectional XON/XOFF flow control enabled GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Note: Used primarily for international data transmission Command Function &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800Hz guard tone enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Calculates and verifies the ROM checksum I2 Calculates and compares the ROM checksum with the pre-stored checksum I3 Reports the firmware version, basic model, application code, and interface type code I4 Reports OEM defined identifier string in either Hayes-compatible binary format or ASCII format I5 Reports country code I6 Reports modem data pump model and internal code revision SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low speaker volume L1 Low volume setting L2 Medium volume setting L3 Highest volume setting