ACER, INC. MAGIC MP32 Card Type Modem, Fax, Sound card Chip Set Unidentified I/O Options CD-ROM interface, microphone, audio line in, audio line out, wavetable interface Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.34bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29, V.33 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 16-bit ISA Card Size Full-length, full-height card [Image] CONNECTIONS Function Label Function Label MIDI/Game port CN1 Wave table interface CN6 Telephone line in CN4 Speaker/Line out CN7 Telephone line out CN5 Line in CN8 Microphone in CN9 CD-Audio JP5 SPEAKER/LINE OUT SETTINGS Function CN2 CN3 Speaker mode enabled (CN7) Pins 1 & 2 closed Pins 1 & 2 closed Line out function enabled Pins 2 & 3 closed Pins 2 & 3 closed SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, B, C, D, E, H, M, O, P, Q, T, V, W, X, Y, Z &C, &F, &P, &Q, &R, &V, &W, &Y, &Z Extended AT Commands \A, \B, \K, \N, \V, %C, %E, %L, %Q, %TT S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 Special Commands #CID, +MS, #BDR, #CLS, MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode detection enabled CLOCK SOURCE - SYNCHRONOUS TRANSMIT Type: Configuration Format: AT [cmds] &Xn [cmds] Description: Selects DTE transmit clock source Command Function &X0 Modem generates clock &X1 Modem generates clock from the receive carrier signal COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode &M1 Synchronous connect mode and asynchronous off-line command mode. &M2 Synchronous connect mode and asynchronous off-line command mode and set DTR high. &M3 Synchronous connect mode and asynchronous off-line command mode and set DTR to low. DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q &Q Setting &D0 &D1 &D2 &D3 &Q0, &Q5, &Q6 Command 0 Command 1 Command 2 Command 3 &Q1, &Q4 Command 2 Command 1 Command 2 Command 3 &Q2, &Q3 Command 2 Command 2 Command 2 Command 2 Command Function Command 0 Modem does not respond to DTR Command 1 Modem goes to command mode after DTR goes is off Command 2 Modem goes to command mode and disconnects (hangs up) after DTR goes off. Command 3 Modem is initialized after DTR goes off FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS and DTE/DCE flow control enabled &K4 XON/XOFF and DTE/DCE flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 RTS/CTS and XON/XOFF flow control enabled GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Note: Used primarily for international data transmission Command Function &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800Hz guard tone enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Reports OK I3 Reports firmware revision, model and interface type I4 Reports response programmed by OEM I5 Reports the country code parameter I6 Reports modem data pump model and code revision SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options Command Function &T0 End current test &T1 Begin local analog loopback test &T2 Returns error result code &T3 Begin local digital loopback &T4 Grant remote digital loopback request &T5 Deny remote digital loopback request &T6 Request remote digital loopback &T7 Request remote digital loopback and self-test &T8 Begin local analog loopback and self-test S(status) -REGISTERS AUTOSYNC OPTIONS Type: Register Format AT [cmds] S19=n Default: 0 Description: Enables selection of the autosync options AUTOSYNC OR BSC SYNC ENABLED Type: Register Format AT [cmds] S20=n Default: 0 Description: Enables autosync HDLC address or BSC sync characters