ARCHTEK CORPORATION 3334BT Card Type Modem/Fax card Chip Set Texas Instruments I/O Options Line out, phone in Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, V.34bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 8-bit ISA Card Size Half-length [Image] CONNECTIONS Function Label Function Label Line out CN2 Phone in CN3 SERIAL PORT ADDRESS Setting J3/A J3/B J3/C COM1 (3F8h) Closed Closed Closed COM2 (2F8h) Open Closed Closed COM3 (3E8h) Closed Open Closed COM4 (2E8h) Open Open Closed Disabled Open Open Open INTERRUPT Setting J4/A J4/B J4/C J4/D J4/E IRQ2 On Off Off Off Off IRQ3 Off On Off Off Off IRQ4 Off Off On Off Off IRQ5 Off Off Off On Off IRQ7 Off Off Off Off On SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, ‘comma’, A/ A, B, E, F, H, M, O, S, V &C, &D, &G, &T, &W, &Z S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25 Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D/ Delays for 125 msec. before proceeding with dial D#,D* Extended touch tone pad tones D$ Displays a list of dial commands REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports four digit product code I1 Reports ROM checksum I2 Reports results of RAM self test I3 Reports product type I4 Reports current modem settings I5 Reports NVRAM settings I6 Reports link diagnostics I7 Reports product configuration I9 Reports plug and play information I11 Reports call statistics SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Displays result codes in originate mode Q3 Displays result codes only in ring mode SELECT CALL PROGRESS RESULT CODES Type: Configuration Format: AT [cmds] Xn [cmds] Description: Enables selection of tone detection and associated result code format options Command Function X0 Busy and dial tone detection disabled; result codes 0 - 4 enabled. X1 Busy and dial tone detection disabled; result codes 0 - 5 & 10 - 25 enabled. X2 Busy tone detection disabled, dial tone detection enabled; result codes 0 - 6 & 10 -155 enabled. X3 Busy tone detection enabled, dial tone detection disabled; result codes 0 - 4, 8 - 155 enabled. X4 Busy and dial tone detection enabled; result codes 0 -1 & 3 - 155 enabled. RESET DEFUALT CONFIGURATION Type: Configuration Format: AT [cmds] Yn [cmds] Description: Tells the modem which profile to use the next time the modem is turned on or reset Command Function Y0 Load profile 0 Y1 Load profile 1 Y2 Generic template Y3 Hardware flow control Y4 Software flow control SOFT RESET Type: Immediate Format: AT [cmds] Zn [cmds] Description: Restores modem profiles previously saved in non-volatile RAM using the &W command. Command Function Z0 Restore NVRAM setting selected by Y command Z1 Restore NVRAM setting 0 Z2 Restore NVRAM setting 1 Z3 Restore factory default setting 0 Z4 Restore factory default setting 1 Z5 Restore factory default setting 2 COMMANDS Type: Configuration Format: AT [cmds] &$ [cmds] Description: Displays a list of ampersand commands MODIFY RESPONSES Type: Configuration Format: AT [cmds] &An [cmds] Description: Determines whether the modem sends MNP responses Command Function &A0 ARQ result codes disabled &A1 Append /ARQ to word CONNECT responses when an error correction connection is made. &A2 Append additional V.32 indicator in result codes for calls at or above 4800bps &A3 Append protocol of call DTE INTERFACE Type: Configuration Format: AT [cmds] &Bn [cmds] Description: Controls DTE interface speed Command Function &B0 Change serial port speed to match rate of connection &B1 Serial port speed is independent of connection speed &B2 In answer mode, serial port speed is fixed only for ARQ calls FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Sets values to standard factory configuration &F1 Sets values to factory configuration 0 &F2 Sets values to factory configuration 1 FLOW CONTROL Type: Configuration Format: AT [cmds] &Hn [cmds] Description: Enables flow control options Command Function &H0 Flow control disabled &H1 Hardware flow control enabled &H2 Software flow control enabled &H3 Hardware and software flow control enabled FLOW CONTROL PASS THROUGH Type: Configuration Format: AT [cmds] &In [cmds] Description: Enables flow control options Command Function &I0 XON/XOFF flow control disabled &I1 Process XON/XOFF signals to your modem and remote system &I2 Process XON/XOFF signals to your modem only DATA COMPRESSION Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables data compression Command Function &K0 Data compression disabled &K1 Data compression is enabled if the DTE data rate is higher than the link rate and the remote DCE supports either MNP5 or V.42bis &K2 Data compression enabled &K3 MNP5 disabled, V.42bis enabled COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Normal mode &M4 V.42 auto-reliable mode &M5 V.42 or MNP reliable mode CONNECTION SPEED UPPER LIMIT Type: Configuration Format: AT [cmds] &Nn [cmds] Description: Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed. Command Function &N0 No maximum connect speed. &N1 Set maximum connect speed to 300bps. &N2 Set maximum connect speed to 1200bps. &N3 Set maximum connect speed to 2400bps. &N4 Set maximum connect speed to 4800bps. &N5 Set maximum connect speed to 7200bps. &N6 Set maximum connect speed to 9600bps. &N7 Set maximum connect speed to 12Kbps. &N8 Set maximum connect speed to 14.4Kbps. &N9 Set maximum connect speed to 16.8Kbps. &N10 Set maximum connect speed to 19.2Kbps. &N11 Set maximum connect speed to 21.6Kbps. &N12 Set maximum connect speed to 24Kbps. &N13 Set maximum connect speed to 26.4Kbps. &N14 Set maximum connect speed to 28.8Kbps. &N15 Set maximum connect speed to 31.2Kbps. &N16 Set maximum connect speed to 33.6Kbps. PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) RECEIVE DATA Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Selects RTS options Command Function &R1 RTS is ignored by modem. &R2 Modem sends data to DTE only if RTS is on DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected CONNECTION SPEED LOWER LIMIT Type: Configuration Format: AT [cmds] &Un [cmds] Description: Sets slowest allowed connection speed if &N is set to 1 or higher. Command Function &U0 No minimum connect speed. &U1 Set minimum connect speed to 300bps. &U2 Set minimum connect speed to 1200bps. &U3 Set minimum connect speed to 2400bps. &U4 Set minimum connect speed to 4800bps. &U5 Set minimum connect speed to 7200bps. &U6 Set minimum connect speed to 9600bps. &U7 Set minimum connect speed to 12Kbps. &U8 Set minimum connect speed to 14.4Kbps. &U9 Set minimum connect speed to 16.8Kbps. &U10 Set minimum connect speed to 19.2Kbps. &U11 Set minimum connect speed to 21.6Kbps. &U12 Set minimum connect speed to 24Kbps. &U13 Set minimum connect speed to 26.4Kbps. &U14 Set minimum connect speed to 28.8Kbps. &U15 Set minimum connect speed to 31.2Kbps. &U16 Set minimum connect speed to 33.6Kbps. BREAK HANDLING Type: Configuration Format: AT [cmds] &Yn [cmds] Description: Sets break handling Command Function &Y0 Destructive, but doesn’t sent break &Y1 Destructive, expedited &Y2 Nondestructive, expedited S(STATUS) -REGISTERS INACTIVITY TIMER Type: Register Format AT [cmds] S19=n [cmds] Default: 0 Unit: 1 second Description: Activates when there is no activity on the phone line. Modem hangs up at time-out Note: S19=0 disables the timer and allows an indefinite duration. MNP OR V.42 MODE DELAY Type: Register Format AT [cmds] S21=n [cmds] Range: Unidentified Unit: 10ms Description: Sets the length of breaks sent from modem to computer. FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S22=n [cmds] Range: Unidentified Unit: ASCII Description: Sets the character used to represent XON FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S23=n [cmds] Range: Unidentified Unit: ASCII Description: Sets the character used to represent XOFF