INDUSTRIAL COMPUTER SOURCE

WINCOMM4

Card Type               Multi-I/O card
Chip Set                Unidentified
Maximum Onboard Memory  Unidentified
I/O Options             Serial ports (4 RS-232)
Hard Drives supported   None
Floppy drives supported None
Data Bus                16-bit ISA

[Image]

                                CONNECTIONS

                Function                              Label

  37-pin octopus connector to four                     CN1
  25-pin serial ports

                          BASE I/O ADDRESS SELECTION

  Setting   SW1-4/1  SW1-4/2   SW1-4/3   SW1-4/4   SW1-4/5   SW1-4/6   SW1-4/7

   000h       On       On        On        On        On        On        On

   008h       On       On        On        On        On        On       Off

   010h       On          On     On        On        On       Off        On

   018h       On       On        On        On        On       Off       Off

   020h       On       On           On        On     Off       On        On

   3D8h      Off       Off       Off       Off       On       Off       Off

   3E0h      Off       Off       Off       Off       Off       On        On

   3E8h      Off       Off       Off       Off       Off       On       Off

   3F0h      Off       Off       Off       Off       Off      Off        On

   3F8h      Off       Off       Off       Off       Off      Off       Off

                                     Note:

  SW4 sets the I/O addresses for port1, SW 3 sets the I/O addresses for port
  2, SW2 sets the I/O addresses for port 3, and SW1 sets the I/O addresses for
  port 4. A total of 128 base address settings are available. The switches are
  a binary representation of the decimal memory addresses. SW1-4/1 is the Most
  Significant Bit and switch SW1-4/7 is the Least Significant Bit. The
  switches have the following decimal values:SW1-4/1=1024, SW1-4/2=512,
  SW1-4/3=256, SW1-4/4=128, SW1-4/5=64, SW1-4/6=32, SW1-4/7=16. Turn off the
  switches and add the values of the switches to obtain the correct memory
  address. (On=0, Off=1)

                      SERIAL PORT INTERRUPT SELECTION

                IRQ                                Position

               IRQ2                        E 1-4/pins 1 & 2 closed

               IRQ3                        E 1-4/pins 3 & 4 closed

               IRQ4                        E 1-4/pins 5 & 6 closed

               IRQ5                        E 1-4/pins 7 & 8 closed

               IRQ6                        E 1-4/pins 9 & 10 closed

               IRQ7                       E 1-4/pins 11 & 12 closed

               IRQ10                      E 1-4/pins 13 & 14 closed

               IRQ11                      E 1-4/pins 15 & 16 closed

               IRQ12                      E 1-4/pins 17 & 18 closed

               IRQ15                      E 1-4/pins 19 & 20 closed

  Note: E4 sets the interrupt to port 1, E3 sets the interrupt to port 2,
  E2 sets the interrupt to port 3, and

  E1 sets the interrupt to port 4.

                         INTERRUPT MODE SELECTION

    Port            Normal             Shared             Shared with
                                                           resistor

      1          E5/pins 3 & 4      E5/pins 2 & 3        E5/pins 1 & 2
                    closed             closed               closed

      2         E5/pins 11 & 12    E5/pins 10 & 11       E5/pins 9 & 10
                    closed             closed               closed

      3          E5/pins 7 & 8      E5/pins 6 & 7        E5/pins 5 & 6
                    closed             closed               closed

      4         E5/pins 15 & 16    E5/pins 14 & 15      E5/pins 13 & 14
                    closed             closed               closed

  Note: To share one interrupt on all four ports it is necessary to
  select the "shared with resistor" setting.

  For 1-3 ports sharing the same interrupt, select the "shared" setting.