NEWCOM, INC. 56IFX(C), 56IFXV(C) Card Type Modem (asynchronous) Chipset Unidentified I/O Options Voice (on 56ifxv(c) only) Maximum Data Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 US Robotics x2 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA Card Size Full height, half length [Image] CONNECTIONS Function Label Function Label Telephone line out CN1 Not used CN4 Telephone line in CN2 Not used CN5 Not used CN3 Note: CN3, CN4, and CN5 may not be present on all models. PLUG-N-PLAY Setting JP1/A JP1/B JP1/C Enabled Closed Closed Closed Disabled Open Open Open Note: If Plug-N-Play mode is enabled, all other jumper settings must also be set for Plug-N-Play. INTERRUPT SELECTION Setting JP1/D JP1/E JP1/F JP1/G JP1/H JP1/I JP1/J 3 Open Open Open Open Open Open Closed 4 Open Open Open Open Open Closed Open 5 Open Open Open Open Closed Open Open 7 Open Open Open Closed Open Open Open 10 Closed Open Open Open Open Open Open 11 Open Closed Open Open Open Open Open 12 Open Open Closed Open Open Open Open Plug-N-Play Closed Closed Closed Closed Closed Closed Closed SERIAL PORT ADDRESS SELECTION Setting JP1/K JP1/L JP1/M JP1/N 3F8h (COM1:) Closed Closed Open Open 2F8h (COM2:) Closed Open Open Closed 3E8h (COM3:) Open Closed Closed Open 2E8h (COM4:) Open Open Closed Closed Plug-N-Play Open Open Open Open SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, C, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z &C, &D, &F, &G, &J, &K, &P, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z %A, %C, %E, %G, %L, %Q Special AT Commands -C, "H, -J, "O S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92 S95 Note: See MHI help file for complete information. IS-101 COMMANDS +V Commands +VCID, +VCSD, +VDR, +VEM, +VGM, +VGR, +VGS, +VGT, +VIP, +VIT, +VLS, +VNH, +VRA, +VRN, +VRX +VSD, +VSM, +VSP, #VSPS, +VTD, +VTS, +VTX -S Commands -SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SQR, -SSP, -SSQ, -SSR, -SSV Note: The functions of the IS-101 commands are unidentified. These commands are supported on 56ifxv(c) only. Proprietary AT Command Set See NEWCOM, INC. 336IFXSP(C) for a full command summary.