BOCA RESEARCH, INC. SOUND EXPRESSION (SE34SRS), SOUND EXPRESSION (SE34SVD) Card Type Sound/Modem card Chip Set Unidentified Maximum Onboard Memory Unidentified I/O Options Game/MIDI port, CD-ROM interface - IDE, Audio in - CD-ROM (3), speaker, line out, line in, microphone in, telephone jack Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.22, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus 16-bit ISA [Image] CONNECTIONS Function Location Function Location Game/MIDI port CN1 Wavetable CN6 Speaker CN2 CD-ROM interface - CN7 IDE Line out CN3 Audio in - CD-ROM J9 (Mitsumi) Line in CN4 Audio in - CD-ROM J10 (Panasonic) RJ-11 telephone CN5 Audio in - CD-ROM J11 jack (Sony/IDE) SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, ‘comma’, A/ A, B, C, E, H, L, M, O, Q, R, S, T, U, V, W, X, Y, Z &C, &F, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B %C, %E, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S28, S29, S30,S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 Special Commands +MS?, +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function D Dial DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. D^ Disable dialing code. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product ID I1 Reports checksum I2 Tests and reports ROM checksum I3 Reports firmware revision I4 Reports OEM-defined identifier string. I5 Reports country code I6 Reports modem data pump model AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Permits handshaking at any speed supported by both modems. DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q &Q Setting &D0 &D1 &D2 &D3 &Q0, &Q5, &Q6 Command 0 Command 3 Command 2 Command 4 &Q1, &Q4 Command 1 Command 3 Command 2 Command 4 &Q2, &Q3 Command 2 Command 2 Command 2 Command 2 Command Function Command 0 Modem does not respond to DTR Command 1 Modem disconnects (hangs up) after DTR goes off; Auto-Answer not affected Command 2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. Command Asynchronous escape sequence 3 Command 4 Modem does a soft reset FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Enable transport XON/XOFF &K6 Enable both RTS/CTS and XON/XOFF BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Break from DTE Break from DTE during Break received from Direct Mode remote modem \K0 Online command mode Break sent to remote Buffers cleared, break enabled, send no modem and command sent to DTE break to remote modem entered \K1 Break sent to remote Break sent to remote Buffers cleared, break modem and buffered modem and command sent to DTE cleared entered \K2 Online command mode Send break with Break sent immediately to enabled, send no transmitted data DTE break to remote modem \K3 Send break to remote Break sent to remote Break sent immediately to modem immediately modem and command DTE entered \K4 Online command mode Send break with Break sent with received enabled, send no transmitted data data to the DTE break to remote modem \K5 Send break with Send break with Break sent with received transmitted data transmitted data data to the DTE CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP reliable mode enabled \N3 Auto-reliable mode or MNP auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 V.42 auto-reliable mode or MNP auto-reliable mode enabled DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Speed of last connection S37=1-3 300bps S37=4 Reserved S37=5 1200bps S37=6 2400bps S37=7 V.23 mode S37=8 4800bps S37=9 9600bps S37=10 12.0Kbps S37=11 14.4Kbps S37=12 7200bps RESULT CODES BASIC RESULT CODES Numeric Verbose Wn Function 0 OK W0 Modem has successfully executed the previous command and has returned to the on-line command state. 1 CONNECT W0 Connection established at unspecified rate. 2 RING W0 Incoming ring detected. 3 NO CARRIER W0 Carrier signal lost or no connection established. 4 ERROR W0 Last command issued was not valid. 5 CONNECT 1200 W0 Connection established at 1200bps. 6 NO DIALTONE W0 No dial tone was detected within the time allotted by S7. 7 BUSY W0 A busy tone was detected after dialing. 8 NO ANSWER W0 No quiet answer (ring-back followed by silence) was detected. 9 CONNECT 600 WO Connection established at 600bps 10 CONNECT 2400 W0 Connection established at 2400bps. 11 CONNECT 4800 W0 Connection established at 4800bps. 12 CONNECT 9600 W0 Connection established at 9600bps. 13 CONNECT 7200 WO Connected as data modem during answer. 14 CONNECT 12000 WO Connection established at 12000bps. 15 CONNECT 14400 W0 Connection established at 14.4K bps. 16 CONNECT 19200 W0 Connection established at 19.2K bps. 17 CONNECT 38400 W0 Connection established at 38.4K bps. 18 CONNECT 57600 W0 Connection established at 57.6K bps. 19 CONNECT 115200 W0 Connection established at 115.2K bps. BASIC RESULT CODES (cont'd) Numeric Verbose Wn Function 22 CONNECT 75/1200 W0 Connection established at transmit 75/receive 1200bps. 23 CONNECT 1200/75 W0 Connection established at transmit 1200/receive 75bps. 24 DELAYED WO Connection fails and number dialed is "delayed" due to country blacklisting. 32 BLACKLISTED WO Connection failed and the number dialed is considered "blacklisted" 33 FAX W0 Fax connection established. 35 DATA W0 Data connection established. EXTENDED RESULT CODES Numeric Verbose Wn Function 40 CARRIER 300 W1 Carrier signal at 300bps is detected. 44 CARRIER 1200/75 W1 Carrier signal at transmit 1200/receive 75bps is detected. 45 CARRIER 75/1200 W1 Carrier signal at transmit 1200/receive 75bps is detected. 46 CARRIER 1200 W1 Carrier signal at 1200bps is detected. 47 CARRIER 2400 W1 Carrier signal at 2400bps is detected. 48 CARRIER 4800 W1 Carrier signal at 4800bps is detected. 49 CARRIER 7200 W1 Carrier signal at 7200bps is detected. 50 CARRIER 9600 W1 Carrier signal at 9600bps is detected. 51 CARRIER 12000 W1 Carrier signal at 12.0K bps is detected. 52 CARRIER 14400 W1 Carrier signal at 14.4K bps is detected. 53 CARRIER 16800 W1 Carrier signal at 16.8K bps is detected. 54 CARRIER 19200 W1 Carrier signal at 19.2K bps is detected. 55 CARRIER 21600 W1 Carrier signal at 21.6K bps is detected. 56 CARRIER 24000 W1 Carrier signal at 24.0K bps is detected. 57 CARRIER 26400 W1 Carrier signal at 26.4K bps is detected. 58 CARRIER 28800 W1 Carrier signal at 28.8K bps is detected. 59 CONNECT 16800 W0 Connection established at 16.8K bps. 61 CONNECT 21600 W0 Connection established at 21.6K bps. 62 CONNECT 24000 W0 Connection established at 24.0K bps. 63 CONNECT 26400 W0 Connection established at 26.4K bps. 64 CONNECT 28800 W0 Connection established at 28.8K bps. 66 COMPRESSION: CLASS W1 MNP Class 5 data compression 5 was negotiated. 67 COMPRESSION: W1 V.42bis data compression was V.42BIS negotiated. 69 COMPRESSION: NONE W1 No data compression was negotiated. 70 PROTOCOL: NONE W1 No protocol was negotiated. 77 PROTOCOL: LAP-M W1 V.42 LAPM error-control was negotiated. 80 PROTOCOL: ALT W1 MNP error-control was negotiated. 81 PROTOCOL: W1 Modem connected in the MNP10 ALT-CELLULAR mode.