RACAL-DATACOM EXCALIBUR BRI 2000 Card Type ISDN TA Chipset Unidentified I/O Options Network management port ISDN Transfer Rate 56Kbps x 2/64Kbps x 2 ISDN Protocol T-Link, V.110, V.120 Switch Type 5ESS, DMS100, NI-1 Data Bus Serial [Image] CONNECTIONS Function Label Function Label Left arrow button BT1 ISDN U interface CN1 ESC button BT2 CMS 400 network CN2 management jack Right arrow button BT3 AC power in CN3 1 button BT4 RS-232 or V.35 serial CN4 port 2 via DB-26 connector 2 button BT5 RS-232 or V.35 serial CN5 port 1 via DB-26 connector 3 button BT6 LCD display LCD Note: Standard RS-232 or V.35 serial port connectors are provided on included adapter cables. USER CONFIGURABLE SETTINGS Setting Label Position Factory configured - do not alter RL/SQ SQ SERIAL PORT 1 CONFIGURATION JB1 RS-232 V.35 [Image] [Image] SERIAL PORT 2 CONFIGURATION JB2 RS-232 V.35 [Image] [Image] MISCELLANEOUS TECHNICAL NOTES To use call bonding, serial port 1 must be used. Serial port 2 only supports speeds of 64Kbps. SUPPORTED STANDARD COMMANDS Basic AT Commands +++, 'comma', A/ A, D, E, H, O, V, X, Z &C, &D, &F, &S, &W, &Z S-Registers S2, S3, S4, S5, S7, S12, S25, S26 V.25bis Commands CIC, CRN, CRS, DIC, PRN Note: See MHI help file for complete information. Proprietary AT Command Set AUTO-ANSWER Type: Register Format: AT [cmds] S0=n [cmds] Default: 1 Range: 0 - 127 Unit: 10 mS Description: Sets the amount of time the TA waits before answering an incoming call. BIT-MAPPED REGISTER S14 Format: AT [cmds] S14=n [cmds] Default: 3 Range: 0 - 3 Description: Controls echo and result code display. Bit Value Function 0 0 Command echo disabled. 1 Command echo enabled. 1 0 Display result codes in numeric format. 1 Display result codes in verbose format. BIT-MAPPED REGISTER S21 Format: AT [cmds] S21=n [cmds] Default: 2 Range: 0 - 27 Description: Controls CTS, DCD, and DSR signals. Bit Value Function 0 0 CTS follows RTS. 1 CTS normal. 1 0 DCD forced high. 1 DCD normal. 3, 2 00 DSR forced high. 01 DSR normal. 10 DSR forced high if ISDN is active. 4 0 DSR forced low during all tests. 1 DSR forced low only if test pattern is active. CALLER ID NUMBER Type: Configuration Format: AT [cmds] @Zn [cmds] Description: Sets the stored number indicated as a Caller ID number for Caller ID security. CLEAR STORED NUMBERS Type: Configuration Format: AT [cmds] @N99 [cmds] Description: Clears all stored telephone numbers. CLEAR STORED NUMBERS - CALLER ID Type: Configuration Format: AT [cmds] &N99 [cmds] Description: Clears all stored numbers set for caller ID. CLOCK SOURCE - RECEIVE Type: Register Format: AT [cmds] S35=n [cmds] Description: Selects the source for the receive clock. Command Function S34=0 Receive clock generated from received signal. S34=1 Receive clock generated from external source. CLOCK SOURCE - TRANSMIT Type: Register Format: AT [cmds] S34=n [cmds] Description: Selects the source for the transmit clock. Command Function S34=0 Transmit clock generated from received signal. S34=1 Transmit clock generated from external source. COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects whether the TA will operate in synchronous or asynchronous mode. Command Function &Q0 TA will operate in asynchronous mode. &Q1 TA will operate in synchronous mode. COMMUNICATIONS MODE Type: Register Format: AT [cmds] S27=n [cmds] Description: Selects whether the TA will operate in synchronous or asynchronous mode. Command Function S27=0 TA will operate in asynchronous mode. S27=1 TA will operate in synchronous mode. DATA FORMAT Format: AT [cmds] S23=n [cmds] Default: 0 Range: 0 - 14 Description: Controls the number of data and stop bits. Bit Value Function 0 0 Not used. 1 0 One stop bit. 1 Two stop bits. 3, 2 00 Eight data bits. 01 Seven data bits. 10 Six data bits. 11 Five data bits. DATA TYPE - B1 CHANNEL Type: Configuration Format: AT [cmds] \C1=n [cmds] Description: Sets the format for data being sent over the B1 channel. Command Function \C1=0 B1 channel carries standard data. \C1=1 B1 channel carries circuit-switched data. DATA TYPE - B2 CHANNEL Type: Configuration Format: AT [cmds] \C2=n [cmds] Description: Sets the format for data being sent over the B2 channel. Command Function \C2=0 B2 channel carries standard data. \C2=1 B2 channel carries circuit-switched data. DIRECTORY NUMBER 1 Type: Configuration Format: AT [cmds] !N1=<#> [cmds] Description: Sets the first Directory Number to the number indicated. DIRECTORY NUMBER 2 Type: Configuration Format: AT [cmds] !N2=<#> [cmds] Description: Sets the second Directory Number to the number indicated. DISPLAY CONFIGURATION Type: Immediate Format: AT [cmds] &Vn [cmds] Description: Displays the indicated part of the TA's configuration. Command Function &V0 Displays the command setting for the port. &V1 Displays all stored telephone numbers. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the TA. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and displays ROM checksum result. I3 Displays firmware part number, revision, and checksum. DTR SIGNAL Type: Configuration Format: AT [cmds] \Dn [cmds] Description: Controls the operation of the DTR signal. Command Function \D0 DTR normal. \D1 DTR forced high. DTR SIGNAL Type: Configuration Format: AT [cmds] S33=n [cmds] Description: Controls the operation of the DTR signal. Command Function S33=0 DTR normal. S33=1 DTR forced high. FRONT PANEL CONTROLS Type: Configuration Format: AT [cmds] @Fn [cmds] Description: Select whether the front panel controls are operative. Command Function @F0 Front panel controls disabled. @F1 Front panel controls enabled. LINE SPEED - B1 CHANNEL Type: Configuration Format: AT [cmds] \B1=n [cmds] Description: Sets the line speed of the B1 channel. Command Function \B1=0 B1 channel speed set to 56Kbps. \B1=1 B1 channel speed set to 64Kbps. LINE SPEED - B2 CHANNEL Type: Configuration Format: AT [cmds] \B2=n [cmds] Description: Sets the line speed of the B2 channel. Command Function \B2=0 B2 channel speed set to 56Kbps. \B2=1 B2 channel speed set to 64Kbps. LOCAL SERIAL PORT SPEED Type: Configuration Format: AT [cmds] Fn [cmds] Description: Sets the speed of the local serial port. Command Function F0 Serial port speed set to 300bps. F1 Serial port speed set to 600bps. F2 Serial port speed set to 1200bps. F3 Serial port speed set to 2400bps. F4 Serial port speed set to 4800bps. F5 Serial port speed set to 7200bps. F6 Serial port speed set to 9600bps. F7 Serial port speed set to 14.4Kbps. F8 Serial port speed set to 19.2Kbps. F9 Serial port speed set to 38.4Kbps. F12 Serial port speed set to 57.6Kbps. LOCAL SERIAL PORT SPEED Type: Register S29=ormat: AT [cmds] S29=n [cmds] Description: Sets the speed of the local serial port. Command S29=unction S29=0 Serial port speed set to 300bps. S29=1 Serial port speed set to 600bps. S29=2 Serial port speed set to 1200bps. S29=3 Serial port speed set to 2400bps. S29=4 Serial port speed set to 4800bps. S29=5 Serial port speed set to 7200bps. S29=6 Serial port speed set to 9600bps. S29=7 Serial port speed set to 14.4Kbps. S29=8 Serial port speed set to 19.2Kbps. S29=9 Serial port speed set to 38.4Kbps. S29=12 Serial port speed set to 57.6Kbps. NETWORK MANAGEMENT ADDRESS Type: Configuration Format: AT [cmds] @CMSA=n [cmds] Default: Unidentified Range: 1 - 255 Unit: N/A Description: Sets the CMS network management address for the TA. NETWORK MANAGEMENT SPEED Type: Configuration Format: AT [cmds] @CMSFn [cmds] Description: Sets the speed of the CMS network management port. Command Function @CMSF0 Set network management port speed to 75bps. @CMSF1 Set network management port speed to 300bps. @CMSF2 Set network management port speed to 1200bps. @CMSF3 Set network management port speed to 2400bps. @CMSF4 Set network management port speed to 4800bps. @CMSF5 Set network management port speed to 9600bps. @CMSF6 Set network management port speed to 19.2Kbps. NETWORK MANAGEMENT TYPE Type: Configuration Format: AT [cmds] @CMSNn [cmds] Description: Sets where the TA is in respect to the CMS network management unit. Command Function @CMSN0 TA is local to the network management unit. @CMSN1 TA is remote from the network management unit. POWER FAIL ALARM DELAY Type: Register Format: AT [cmds] S30=n [cmds] Default: 10 Range: 0 - 127 Unit: 1 second Description: Sets the amount of time the TA waits after the DTE loses power before generating an alarm condition. PROTOCOL - RATE ADAPTATION Type: Register Format: AT [cmds] S28=n [cmds] Description: Selects the rate adaptation protocol the TA will use. Command Function S28=0 TA will use V.120 for rate adaptation. S28=1 TA will use T-Link for rate adaptation. REDIAL DELAY Type: Register Format: AT [cmds] S44=n [cmds] Default: 30 Range: 0 - 127 Unit: .5 second Description: Sets the amount of time the TA will wait before redialing a call that did not connect. RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables TA to send result codes to the DTE. Command Function Q0 Result codes enabled. Q1 Result codes disabled. Q2 Result codes enabled in originate mode only. RTS SIGNAL Type: Register Format: AT [cmds] S32=n [cmds] Description: Controls the operation of the RTS signal. Command Function S32=0 RTS forced high. S32=1 RTS normal. SECURITY Type: Configuration Format: AT [cmds] @Cn [cmds] Description: Selects what type of security will be used for dial-in. Command Function @C0 Security disabled. @C1 Caller ID security enabled. @C2 Password security enabled. SECURITY Type: Register Format: AT [cmds] S42=n [cmds] Description: Selects what type of security will be used for dial-in. Command Function S42=0 Security disabled. S42=1 Caller ID security enabled. S42=2 Password security enabled. SPID 1 Type: Configuration Format: AT [cmds] \SP1=<#> [cmds] Description: Sets the first Service Profile ID to the number indicated. SPID 2 Type: Configuration Format: AT [cmds] \SP2=<#> [cmds] Description: Sets the second Service Profile ID to the number indicated. SPID DISABLE Type: Configuration Format: AT [cmds] \SP0 [cmds] Description: Disables both Service Profile ID's. SWITCH TYPE Type: Configuration Format: AT [cmds] \Sn [cmds] Description: Sets the type of switch the TA is connected to. Command Function \S0 TA is connected to AT&T 5ESS switch. \S1 TA is connected to DMS-100 switch. \S2 TA is connected to National NI-1 switch. Proprietary V.25bis Command Set REQUEST LISTED NUMBERS Type: Immediate Format: RLN Description: Requests the modem to return the list of stored numbers.