ADDTRON TECHNOLOGY CO., LTD. ARF-3314V/SP Card Type Modem (synchronous/asynchronous) Chipset Unidentified I/O Options Microphone in, speaker out, voice Maximum Data Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Unidentified Fax Modulation Unidentified Error Correction/Compression MNP5, MNP10EC, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA Card Size Full height, half length [Image] CONNECTIONS Function Label Function Label Telephone line out CN1 Microphone in CN3 Telephone line in CN2 Speaker out CN4 USER CONFIGURABLE SETTINGS Setting Label Position Factory configured - do not alter JP8 Open Factory configured - do not alter JP9 Open Factory configured - do not alter JP10 Open Factory configured - do not alter JP11 Open Factory configured - do not alter JP12 Open Factory configured - do not alter JP13 Open Factory configured - do not alter JP14 Open Internal audio amplifier enabled JP17 Pins 2 & 3 closed Internal audio amplifier disabled JP17 Pins 1 & 2 closed Microphone jack used for voice JP18 Pins 1 & 2 closed Microphone jack used for music on hold JP18 Pins 2 & 3 closed PLUG-N-PLAY Setting JP15 JP16 Disabled Pins 1 & 2 closed Pins 1 & 2 closed Enabled Pins 2 & 3 closed Pins 2 & 3 closed Note: If Plug-N-Play mode is enabled, all other jumper settings must also be set for Plug-N-Play. SERIAL PORT ADDRESS SELECTION Setting JP2 JP3 JP4 JP5 3F8h (COM1:) Closed Open Closed Open 2F8h (COM2:) Open Closed Closed Open 3E8h (COM3:) Closed Open Open Closed 3E8h (COM4:) Open Closed Open Closed Plug-N-Play Open Open Open Open INTERRUPT SELECTION Setting JP6 JP7 3 Closed Open 4 Open Closed Plug-N-Play Open Open SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &J, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \N, \V %C, %E, %L, %Q, %TT Special AT Commands #CID, -K S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S27 S30, S31, S32, S33, S37 Note: See MHI help file for complete information. IS-101 COMMANDS -S Commands -DTP, -SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SMT, -SQR, -SSQ, -SSR, -SVV Note: The functions of the IS-101 commands are unidentified. Proprietary AT Command Set BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal. Command Function \K0 Online command mode enabled, break not sent to remote modem. \K1 Break sent to remote modem and buffers cleared. \K2 Online command mode enabled, break not sent to remote modem. \K3 Break sent to remote modem immediately. \K4 Online command mode enabled, break not sent to remote modem. \K5 Break sent with transmitted data. DISPLAY CHIPSET MANUFACTURER Type: Immediate Format: AT [cmds] #MFR? [cmds] Description: Displays the voice chipset manufacturer’s name. DISPLAY CHIPSET MODEL NAME Type: Immediate Format: AT [cmds] #MDL? [cmds] Description: Displays the model name of the modem's voice chipset. DISPLAY CHIPSET REVISION Type: Immediate Format: AT [cmds] #REV? [cmds] Description: Displays the revision level of the modem's voice chipset. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays chip firmware revision. I2 Tests and displays ROM checksum result. I3 Displays chipset manufacturer. I4 Displays chipset configuration. I5 Displays reserved chipset configuration. I6 Displays country code. I7 Displays board firmware revision. I8 Displays firmware features. MNP10EC MODE Type: Configuration Format: AT [cmds] -SEC=n [cmds] Description: Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence. Command Function -SEC=0 MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line. -SEC=1 MNP10EC handshaking enabled. MODE SELECTION Type: Immediate Format: AT [cmds] #CLS=n [cmds] Description: Selects which mode the modem will operate in. Command Function #CLS=0 Modem will operate in data mode. #CLS=1 Modem will operate in fax class 1 mode. #CLS=8 Modem will operate in voice mode. TONE DETECTION Format: AT [cmds] #VTD=x,y,z [cmds] Default: x,y,z 63 Range: 0 - 63 Description: Sets which tones the tone detection will report. Note: The value of x sets the tone detection modes in voice transmit mode, y sets them in voice receive mode, and z sets them in voice command mode. Bit Value Function 0 0 DTMF tones are not detected. 1 DTMF tones are detected. 1 0 V.25 1300Hz calling tone is not detected. 1 V.25 1300Hz calling tone is detected. 2 0 T.30 1100Hz fax tone is not detected. 1 T.30 1100Hz fax tone is detected. 3 0 V.25/T.30 2100Hz answer tone is not detected. 1 V.25/T.30 2100Hz answer tone is detected. 4 0 Bell 2225Hz answer tone is not detected. 1 Bell 2225Hz answer tone is detected. 5 0 Call progress tones are not detected. 1 Call progress tones are detected. TONE GENERATOR - DIRECT ENTRY Type: Immediate Format: AT [cmds] #VTS=[m, n, x] Range: m 200-3000, n 200-3000, x 0-255 Unit: m 1 Hz, n 1 Hz, x .1 second Description: Generates a dual-frequency tone for duration x at frequencies m and n. TONE GENERATOR - TIMED PHONE KEYS Type: Immediate Format: AT [cmds] #VTS={a, n} Range: a 0-9, A-D, #, *; x 0-255 Unit: x .1 second Description: Generates the DTMF tone for duration x for the character a. TONE GENERATOR - PHONE KEYS Type: Immediate Format: AT [cmds] #VTS=a Range: 0-9, A-D, #, * Description: Generates the DTMF tones for the characters in the string for the duration set with +VBT. TONE GENERATOR LENGTH Format AT [cmds] #VBT=n [cmds] Default: 10 Range: 0 - 40 Unit: 0.1 second Description: Sets the length of DTMF tones that are generated. VOICE BUFFER SPACE Type: Configuration Format: AT [cmds] #VSK=n [cmds] Default: 255 Range: 0 - 255 Unit: 1 byte Description: Sets the amount of data the modem can send into the buffer after the XOFF signal is sent. VOICE DEVICE Type: Configuration Format: AT [cmds] #VLS=n [cmds] Description: Selects the I/O device for the DSP chip. Note: This modem may not support all options listed below. The #VLS? command will display the available options. Command Function #VLS=0 Telephone line and handset used for voice I/O. #VLS=1 Telephone handset used for voice I/O. #VLS=2 Internal speaker only used for voice I/O. #VLS=3 External microphone only used for voice I/O. #VLS=4 Telephone line and handset used for voice I/O; internal speaker enabled. #VLS=5 Headset used for voice I/O. #VLS=6 Speakerphone used for voice I/O. #VLS=7 Handset muted by disconnecting handset or speakerphone from telephone line. #VLS=8 Connects caller ID relay for recording of conversation over handset. #VLS=9 Connects handset (or speakerphone) to DSP chip for recording or playback. VOICE - DISPLAY BUFFER SIZE Type: Immediate Format: AT [cmds] #VBQ? [cmds] Description: Displays the size of the voice buffer. VOICE - DISPLAY COMPRESSION TYPE Type: Immediate Format: AT [cmds] #VCI? [cmds] Description: Displays the type of compression currently in use. VOICE - LOCAL SERIAL PORT SPEED Type: Configuration Format: AT [cmds] #BDR=n [cmds] Default: 0 Range: 0 - 48 Unit: 2400bps Description: Sets the speed of the local serial port when in voice mode. A value of 0 indicates that the modem should auto-detect the correct serial port speed. VOICE RE-RING DETECT TIME Type: Configuration Format: AT [cmds] #VRA=n [cmds] Default: 70 Range: 0 -255 Unit: 10 mS Description: Sets the maximum time the modem will wait for the remote station to ring again before it assumes that it has gone off-hook. VOICE RECEIVE Type: Immediate Format: AT [cmds] #VRX Description: Commands the modem to begin receiving voice data. VOICE RING DETECT TIME Type: Configuration Format: AT [cmds] #VRN=n [cmds] Default: 70 Range: 0 - 255 Unit: .1 second Description: Sets the maximum time the modem will wait for the remote station to ring before it assumes that it went off-hook before it rang. VOICE SAMPLE QUALITY Type: Configuration Format: AT [cmds] #VBS=n [cmds] Description: Selects the number of bits per sample that the modem records. Note: This modem may not support all options listed below. The #VBS? command will display the available options. Command Function #VBS=2 Modem records 2 bits per sample in ADPCM encoding. #VBS=3 Modem records 3 bits per sample in ADPCM encoding. #VBS=4 Modem records 4 bits per sample in ADPCM encoding. #VBS=8 Modem records 8 bits per sample in PCM encoding. #VBS=16 Modem records 16 bits per sample in PCM encoding. VOICE SAMPLING RATE Type: Configuration Format: AT [cmds] #VSR=n [cmds] Description: Sets the sampling rate used when recording voice signals. Command Function #VSR=7200 Selects a sampling rate of 7.2KHz. #VSR=8000 Selects a sampling rate of 8KHz. #VSR=11025 Selects a sampling rate of 11.025KHz in PCM encoding only. VOICE SILENCE DETECTION TIME Type: Configuration Format: AT [cmds] #VSP=n [cmds] Default: 55 Range: 0 - 255 Unit: .1 second Description: Sets the minimum amount of silence that the modem will detect. VOICE SILENCE DETECTION THRESHOLD Type: Configuration Format: AT [cmds] #VSS=n [cmds] Description: Sets the threshold of sensitivity that the modem uses to determine silence detection. Command Function #VSS=0 Silence detection disabled. #VSS=1 Minimum silence detection sensitivity. #VSS=2 Standard silence detection sensitivity. #VSS=3 Maximum silence detection sensitivity. VOICE TIMING MARK Type: Configuration Format: AT [cmds] #VTM=n [cmds] Description: Configures timing mark placement. Command Function #VTM=0 Timing marks disabled. #VTM=1 Timing marks enabled. VOICE TRANSMISSION LEVEL Type: Configuration Format: AT [cmds] #TL=hhhh [cmds] Default: 3FFF Range: 0000 - 7FFF Unit: Unidentified (hexadecimal) Description: Sets the transmission level for sending audio in voice mode. VOICE TRANSMIT Type: Immediate Format: AT [cmds] #VTX Description: Commands the modem to begin transmitting voice data. VOICE VOLUME LEVEL Type: Configuration Format: AT [cmds] #VGT=n [cmds] Description: Sets the volume level when playing back audio signals. Command Function #VGT=128 Low volume setting. #VGT=129 Medium volume setting. #VGT=130 High volume setting. #VGT=131 Highest volume setting.