NEWCOM, INC. 336IFXSP(C) Card Type Modem (asynchronous) Chipset Unidentified I/O Options Audio line out, microphone in, speaker out, voice, speakerphone Maximum Data Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA Card Size Full height, half length [Image] CONNECTIONS Function Label Function Label Telephone line out CN1 Headphone line out CN4 Telephone line in CN2 Speaker out CN5 Microphone in CN3 PLUG-N-PLAY Setting JP1/A JP1/B JP1/C Enabled Closed Closed Closed Disabled Open Open Open Note: If Plug-N-Play mode is enabled, all other jumper settings must also be set for Plug-N-Play. INTERRUPT SELECTION Setting JP1/D JP1/E JP1/F JP1/G JP1/H JP1/I JP1/J 3 Open Open Open Open Open Open Closed 4 Open Open Open Open Open Closed Open 5 Open Open Open Open Closed Open Open 7 Open Open Open Closed Open Open Open 10 Closed Open Open Open Open Open Open 11 Open Closed Open Open Open Open Open 12 Open Open Closed Open Open Open Open Plug-N-Play Closed Closed Closed Closed Closed Closed Closed SERIAL PORT ADDRESS SELECTION Setting JP1/K JP1/L JP1/M JP1/N 3F8h (COM1:) Closed Closed Open Open 2F8h (COM2:) Closed Open Open Closed 3E8h (COM3:) Open Closed Closed Open 2E8h (COM4:) Open Open Closed Closed Plug-N-Play Open Open Open Open SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, C, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z &C, &D, &F, &G, &J, &K, &P, &S, &T, &W, &Y, &Z Extended AT Commands \A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z %A, %C, %E, %G Special AT Commands -C, "H, -J, "O S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S27 S30, S31, S33, S37 Note: See MHI help file for complete information. IS-101 COMMANDS +V Commands +VBT, +VCID, +VCSD, +VDR, +VEM, +VGM, +VGR, +VGS, +VGT, +VIP, +VIT, +VLS, +VNH, +VRA, +VRN +VRX, +VSD, +VSM, +VSP, +VTD, +VTS, +VTX, #VSPS -S Commands -SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SQR, -SSP, -SSQ, -SSR, -SSV Note: The functions of the IS-101 commands are unidentified. Proprietary AT Command Set BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal. Command Break from DTE Break from DTE Modem receives \B Break from remote modem Reliable/Normal Direct mode mode \K0 Enter command mode, Send break to Buffers cleared Buffers cleared do not send break remote modem and break sent to and break sent to to remote modem. immediately, then remote modem. DTE. enter command mode. \K1 Buffers cleared and Send break to Buffers cleared Buffers cleared break sent to remote modem and break sent to and break sent to remote modem. immediately. remote modem. DTE. \K2 Enter command mode, Send break to Send break to Send break to DTE do not send break remote modem remote modem immediately. to remote modem. immediately, then immediately. enter command mode. \K3 Send break to Send break to Send break to Send break to DTE remote modem remote modem remote modem immediately. immediately. immediately. immediately. \K4 Enter command mode, Send break to Send break to Break sent with do not send break remote modem remote modem with received data to to remote modem. immediately, then transmitted data. the DTE. enter command mode. \K5 Send break with Send break to Send break to Break sent with transmitted data. remote modem remote modem with received data to immediately. transmitted data. the DTE. COMMUNICATION PROTOCOLS Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects the communication protocol for low-speed data calls. Command Protocol B0 Modem will use ITU-T V.22 at 1200bps. B1 Modem will use Bell 212A at 1200bps. B2 Modem will use ITU-T V.23 at 1200/75bps. B3 Modem will use ITU-T V.23 at 75/1200bps. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays chip firmware revision. I2 Tests and displays ROM checksum result. I3 Displays modem chipset name. I5 Displays hardware configuration. I6 Displays country code. I7 Displays board firmware revision. I8 Displays chipset feature bitmap. I10 Displays board feature bitmap. I11 Displays board feature bitmap. I14 Displays digital SAFE device information. I20 Displays the revision level of the modem's voice chipset. I21 Displays the revision level of the modem's voice firmware. I22 Displays the voice chipset manufacturer’s name. I23 Displays the model name of the modem's voice chipset. DISPLAY PROFILES Type: Immediate Format: AT [cmds] &Vn [cmds] Description: Displays active and stored configuration profiles. Command Function &V0 Displays stored profile 0. &V1 Displays stored profile 1. &V3 Displays relay status and I/O information. EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] Wn [cmds] Description: Selects which result codes the modem will report. Command Function W0 Enables CONNECT result codes to report DTE speed. W1 Enables CONNECT result codes to report DTE speed. W2 Enables CONNECT result codes to report DCE speed. W3 Enables CONNECT result codes to report DTE speed with error correction and compression information. W4 Enables CONNECT result codes to report DTE speed with modulation protocol, error correction, and compression information. MODE SELECTION Type: Immediate Format: AT [cmds] +FCLASS=n Description: Sets what mode the modem will operate in. Command Function +FCLASS=0 Data mode. +FCLASS=1 Class 1 fax mode. +FCLASS=8 Voice mode. +FCLASS=80 IS-101 voice mode. TRELLIS CODING Type: Configuration Format: AT [cmds] &Un [cmds] Description: Selects whether the modem will use trellis coding. Command Function &U0 Trellis coding enabled. &U1 Trellis coding disabled.