MOTOROLA, INC. MODEMSURFR 56K (INTERNAL) Card Type Modem (asynchronous) Chip Set Rockwell Maximum Modem Rate 56Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC, K56+ Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 16-bit ISA Card Size Three-quarter length, full-height [Image] CONNECTIONS Function Label Function Label Telephone line CN1 Telephone line CN2 SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &P, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \K, \N, \V %C, %E, %L, %Q Special AT Commands #CID, +MS S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 S26, S27, S28, S29, S30, S32, S33, S36, S38, S39, S40, S46, S48, S82, S86, S91, S92, S95 Note: See MHI help file for complete information. UNIDENTIFIED COMMANDS Command Default +ES=nnn 3,0,2 +ESA=nnnnnnnn 0,0,0,0,0,0,0,0 +ITF=nn 255,64 Proprietary AT Command Set BIT-MAPPED REGISTER S31 Format: AT [cmds] S31=n [cmds] Default: 2 Range: 0 - 43 Description: Select automode, extended result code format, and caller ID format. Bit Value Function 0 0 Extended result codes controlled by S95. 1 Extended result codes set for single-line format. 1 0 Auto-mode detection disabled 1 In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103 3, 2 00 Enables CONNECT result codes to report DTE speed 01 Full reporting of CONNECT result codes 10 Enables CONNECT result codes to report DCE speed 5, 4 00 Caller ID disabled. 01 Caller ID displays formatted data. 10 Caller ID displays raw hexadecimal data. BIT-MAPPED REGISTER S41 Format AT [cmds] S41=n [cmds] Default: 71 Range: 0 - 71 Description: Selects compression and auto-retrain. Bit Value Function 1, 0 00 Data compression disabled. 01 MNP5 enabled. 10 V.42bis enabled. 11 MNP5 and V.42bis enabled. 6, 2 00 Auto-retrain disabled. 01 Auto-retrain enabled. 11 Auto-fallback/fall-forward enabled. 5 - 3 000 Not used. DIAL Type: Immediate Format: AT [cmds] D<#>;[cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DL Re-dial last number. DP Pulse dialing enabled. DS=n Dial stored telephone number n. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D> Transmit grounding pulse. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D& Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D* Toggles calling tone on or off for this call. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY BLACKLIST NUMBERS Type: Immediate Format: AT [cmds] *B [cmds] Description: Displays the list of all the numbers on the blacklist and their statuses. DISPLAY DELAYED NUMBERS Type: Immediate Format: AT [cmds] *D [cmds] Description: Displays the list of all delayed numbers and their statuses. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and displays ROM checksum result. I3 Displays firmware revision, model, and interface. I4 Displays product name. I5 Displays country code. I6 Displays data pump model and revision. DISTINCTIVE RING Format: AT [cmds] -SDR=n [cmds] Default: Unidentified Range: 0 - 7 Description: Selects which distinctive ring signals the modem will respond to. Bit Value Function 0 0 Do not respond to distinctive ring type 1. 1 Respond to distinctive ring type 1. 1 0 Do not respond to distinctive ring type 2. 1 Respond to distinctive ring type 2. 2 0 Do not respond to distinctive ring type 3. 1 Respond to distinctive ring type 3. RPI CONFIGURATION Type: Configuration Format: AT [cmds] +Hn [cmds] Description: Configures the Rockwell Protocol Interface. Command Function +H0 RPI disabled. +H1 RPI enabled and local serial port speed set to 19.2Kbps. +H2 RPI enabled and local serial port speed set to 38.4Kbps. +H3 RPI enabled and local serial port speed set to 57.6Kbps. +H11 RPI+ enabled.