UNIQUE HARDWARE CO., LTD. FAXSENGER 34 Card Type Modem (synchronous/asynchronous) Chipset Unidentified Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I & II Data Bus Serial [Image] CONNECTIONS Function Label Function Label 4 AA alkaline cells (on BAT DC power in CN4 bottom) Serial port CN1 Telephone line out CN5 Serial port CN2 Power switch SW1 DC power in CN3 DIAGNOSTIC LED(S) LED Color Status Condition 288 Green On Modem connected at 28.8Kbps 288 Green Off Modem connected at slower than 28.8Kbps 144 Green On Modem connected at 14.4Kbps or faster 144 Green Off Modem connected at slower than 14.4Kbps EC Green On Error correction enabled EC Green Off Error correction disabled LBAT Green On Batteries are low LBAT Green Off Batteries are good AA Green On Auto-answer enabled AA Green Off Auto-answer disabled AA Green Blinking Phone is ringing CD Green On Carrier signal detected CD Green Off Carrier signal not detected OH Green On Modem is off-hook OH Green Off Modem is on-hook OH Green Blinking Modem is dialing in pulse mode DIAGNOSTIC LED(S) (CON'T) LED Color Status Condition SD Green On Modem is transmitting data SD Green Off Modem is not transmitting data RD Green On Modem is receiving data RD Green Off Modem is not receiving data TR Green On DTR signal is high TR Green Off DTR signal is low PWR Green On Power is on PWR Green Off Power is off FAX/TM Green On Modem is connected in FAX mode FAX/TM Green Blinking Modem is in test mode FAX/TM Green Off Modem is not connected in FAX mode SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z Extended AT Commands \A, \B, \G, \K, \L, \N %C, %E, %L, %Q Special AT Commands +MS S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26 S27, S29, S30, S31, S32, S33, S36, S38, S40, S41, S46, S48, S82, S86, S95 Note: See MHI help file for complete information. Proprietary AT Command Set DIAL Type: Immediate Format: AT [cmds] D<#>;[cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DJ MNP10 link will be negotiated at highest possible speed for this call. DL Re-dial last number. DP Pulse dialing enabled. DS=n Dial stored telephone number n. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Calling tone disabled for this call. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and displays ROM checksum result. I3 Displays firmware revision. I4 Displays chipset model. I5 Displays country code. I6 Displays product name. DISTINCTIVE RING Type: Configuration Format: AT [cmds] &In [cmds] Description: Selects which distinctive ring signals the modem will respond to. Command Function &I0 Modem will respond to any ring signal. &I1 Modem will only respond to Homefax II type B ring signal. FLOW CONTROL Type: Register Format AT [cmds] S39=n [cmds] Description: Selects the type of flow control the modem will use. Command Function S39=0 Flow control disabled. S39=3 RTS/CTS flow control enabled. S39=4 XON/XOFF flow control enabled. S39=5 Transparent XON/XOFF flow control enabled. S39=6 Both RTS/CTS and XON/XOFF flow control enabled. LINE SPEED Type: Register Format: AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during the handshaking process. Command Function S37=0 Attempt to connect at fastest common speed. S37=1 Set speed to 300bps. S37=2 Set speed to 300bps. S37=3 Set speed to 300bps. S37=5 Set speed to 1200bps. S37=6 Set speed to 2400bps. S37=7 Attempt to connect with V.23. S37=8 Set speed to 4800bps. S37=9 Set speed to 9600bps. S37=10 Set speed to 12Kbps. S37=11 Set speed to 14.4Kbps. S37=12 Set speed to 7200bps. PROTOCOL/SPEED Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects the protocol and speed the modem will attempt to connect at. Command Function F0 Auto-detect the highest common connect speed. F1 Select V.21 or Bell 103 at 300bps speed. F4 Select V.22 or Bell 212A at 1200bps speed. F5 Select V.22bis at 2400bps speed. F6 Select V.32 or V.32bis at 4800bps speed. F7 Select V.32bis at 7200bps speed. F8 Select V.32bis or V.32 at 9600bps speed. F9 Select V.32bis at 12Kbps speed. F10 Select V.32bis at 14.4Kbps speed.