AMQUEST CORPORATION

AM2814I-V34, AM2814I-HY

Card Type                    Modem (synchronous/asynchronous)
Chipset                      Rockwell
Maximum Data Rate            28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Modulation              Bell 103A, 212A

                             ITU-T V.22bis, V.32, V.32bis, V.34

                             Rockwell V.FC
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, MNP10, V.42, V.42bis
Fax Class                    Class I & II
Data Bus                     8-bit ISA
Card Size                    Full height, one-third length

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  Telephone line               CN1     Telephone line               CN2

                        USER CONFIGURABLE SETTINGS

                      Setting                        Label     Position

  Factory configured - do not alter                  SW1/7       Off

  Factory configured - do not alter                  SW1/8       Off

            Note: SW1/8 may not be present on all models.

         SERIAL PORT ADDRESS SELECTION

    Setting          SW1/5          SW1/6

  3F8h (COM1:)        On              On

  2F8h (COM2:)        Off             On

  3E8h (COM3:)        On             Off

  2E8h (COM4:)        Off            Off

                 INTERRUPT SELECTION

  Setting    SW1/1      SW1/2      SW1/3      SW1/4

     3        Off        Off        Off        On

     4        Off        Off        On         Off

     5        Off         On        Off        Off

     7         On        Off        Off        Off

                   SUPPORTED STANDARD COMMANDS

                        Basic AT Commands

  +++, ‘comma’, A/

  A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

                       Extended AT Commands

  \A, \B, \G, \L, \W

  %C, %E, %F, %L, %Q

                       Special AT Commands

  #CID, :E, *H, -K, )M, @M, -Q

                           S-Registers

  The S-registers are unidentified.

            Note: See MHI help file for complete information.

                         Proprietary AT Command Set

                                BREAK TYPE

  Type:          Configuration

  Format:        AT [cmds] \Kn [cmds]

  Description:   Configures action of break signal.

    Command                              Function

      \K0        Enter command mode, do not send break to remote modem.

      \K1        Buffers cleared and break sent to remote modem.

      \K2        Enter command mode, do not send break to remote modem.

      \K3        Send break to remote modem immediately.

      \K4        Enter command mode, do not send break to remote modem.

      \K5        Send break with transmitted data.

                                   DIAL

  Type:                  Immediate

  Format:                AT [cmds] D<#>;[cmds]

  Description:           Dials the telephone number indicated according
                         to any modifiers included in the string.

        Command                              Function

           DJ            MNP10 link will be negotiated at 1200bps for
                         this call.

           DK            MNP10 power level adjustment enabled for this
                         call.

           DL            Re-dial last number.

           DP            Pulse dialing enabled.

           DR            Answer mode enabled; originate mode disabled
                         following handshake initiation.

          DS=n           Dial stored telephone number n.

           DT            Tone dialing enabled.

           DW            Dialing resumed following dial tone detection.

           D,            Dialing paused for amount of time specified in
                         S8 register.

           D!            Flash function initiated. Modem commanded to go
                         off-hook for specified time before returning
                         on-hook.

           D@            Wait for Quiet Answer function enabled. Modem
                         waits until a "quiet answer," a ring-back signal
                         followed by silence up to the time specified in
                         S7, is received prior to executing the rest of
                         the dial string.

           D^            Calling tone disabled for this call.

           D&            Wait for prompt tone detection function enabled.
                         Waits for prompt tone for amount of time
                         specified by the S7 command.

           D;            Modem returned to idle state after dialing. The
                         semicolon can only be placed at the end of the
                         dial command.

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I2        Tests and displays ROM checksum result.

       I3        Displays firmware revision.

       I6        Displays modem pump model.

                              PROTOCOL/SPEED

  Type:             Configuration

  Format:           AT [cmds] Fn [cmds]

  Description:      Selects the protocol and speed the modem will attempt
                    to connect at.

     Command                              Function

        F0          Auto-detect the highest common connect speed.

        F1          Select V.21 or Bell 103 at 300bps speed.

        F3          Select V.23 at 75/1200bps speed.

        F4          Select V.22 or Bell 212A at 1200bps speed.

        F5          Select V.22bis at 2400bps speed.

        F6          Select V.32 or V.32bis at 4800bps speed.

        F7          Select V.32bis at 7200bps speed.

        F8          Select V.32bis or V.32 at 9600bps speed.

        F9          Select V.32bis at 12Kbps speed.

       F10          Select V.32bis at 14.4Kbps speed.