SHARK MULTIMEDIA BABY TIGER-288R Card Type Modem Chipset Rockwell RCV288DPi I/O Options Microphone in, modem audio, speaker out, voice, speakerphone, DVSD Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29, V.33 Error Correction/Compression MNP5, MNP10, V.42, V.42bis Fax Class Class I & II Data Bus 16-bit ISA Card Size Full height, half length [Image] CONNECTIONS Function Label Function Label Telephone line in CN1 Speaker out CN4 Telephone line out CN2 Modem audio in/out CN5 Microphone in CN3 SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z Extended AT Commands \A, \B, \K, \N %C, %E, %L, %Q Special AT Commands #CID, +MS S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 S26, S27, S29, S30, S31, S32, S33, S36, S38, S39, S46, S48, S86, S91, S92, S95, S201 Note: See MHI help file for complete information. Proprietary AT Command Set AUTOSYNC OPTIONS Type: Register Format AT [cmds] S19=n [cmds] Default: 26 Range: 0 - 30 Description: Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle. Bit Value Function 0 0 Not used 1 0 Binary synchronous protocol used. 1 HDLC protocol used. 2 0 HDLC address detect disabled. 1 HDLC address detect enabled. 3 0 NRZI bit coding used. 1 NRZ bit coding used. 4 0 HDLC idle sends MARK. 1 HDLC idle sends FLAG or SYNC. AUTOSYNC HDLC ADDRESS Type: Register Format: AT [cmds] S20=n [cmds] Default: 0 Range: 0-255 Unit: Unidentified Description: Sets the HDLC address and binary synchronous character. BIT-MAPPED REGISTER S28 Format AT [cmds] S28=n [cmds] Default: 0 Range: 0 - 153 Description: Controls V.23 split speed, half duplex, pulse dialing, and MNP10 link negotiation. Bit Value Function 2 - 0 000 Not used. 4, 3 00 39ms make/61ms break at 10pps. 01 33ms make/67ms break at 10pps. 10 39ms make/61ms break at 20pps. 11 33ms make/67ms break at 20pps. 5 0 Not used. 7, 6 00 Link will be negotiated at highest possible speed. 01 Link will be negotiated at 1200bps. 10 Link will be negotiated at 4800bps. BIT-MAPPED REGISTER S40 Format AT [cmds] S40=n [cmds] Default: 107 Range: 0 - 255 Description: Controls power level and break handling; selects MNP extended services, link negotiation, and block size. Bit Value Function 0 0 MNP10 disabled. 1 MNP10 enabled. 1 0 MNP10 at 2400 and 1200bps disabled. 1 MNP10 at 2400 and 1200bps enabled. 2 0 Power level adjustment enabled. 1 Power level adjustment disabled. 5, 4, 3 000 \K0 set. 001 \K1 set. 010 \K2 set. 011 \K3 set. 100 \K4 set. 101 \K5 set. 7, 6 00 MNP block size is 64 characters. 01 MNP block size is 128 characters. 10 MNP block size is 192 characters. 11 MNP block size is 256 characters. BIT-MAPPED REGISTER S41 Format AT [cmds] S41=n [cmds] Default: 131 Range: 0 - 139 Description: Selects compression, auto-retrain and auto-fallback/fall-forward, and low-speed MNP10. Note: Be aware that bit 6 is out of order. Bit Value Function 1, 0 00 Data compression disabled. 01 MNP5 enabled. 10 V.42bis enabled. 11 MNP5 and V.42bis enabled. 6, 2 00 Auto-retrain disabled. 01 Auto-retrain enabled. 10 Auto-fallback/fall-forward enabled. 5 - 3 000 Not used. 7 0 MNP10 at 2400 and 1200bps disabled. 1 MNP10 at 2400 and 1200bps enabled. DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DJ MNP10 link will be negotiated at 1200bps for this call. DK MNP10 power level adjustment enabled for this call. DL Re-dial last number. DP Pulse dialing enabled. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Calling tone toggled from current state for this call. D& Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I1 Displays ROM checksum. I3 Displays firmware model, revision, and interface. I4 Displays OEM string. I5 Displays country code. I6 Displays data pump model and revision. I7 Displays the DAA code. DISTINCTIVE RING Format: AT [cmds] -SDR=n [cmds] Default: Unidentified Range: 0 - 7 Description: Selects which distinctive ring signals the modem will respond to. Bit Value Function 0 0 Do not respond to distinctive ring type 1. 1 Respond to distinctive ring type 1. 1 0 Do not respond to distinctive ring type 2. 1 Respond to distinctive ring type 2. 2 0 Do not respond to distinctive ring type 3. 1 Respond to distinctive ring type 3. DSVD MODE Type: Configuration Format: AT [cmds] -SSE=n [cmds] Description: Select whether the modem will use DSVD mode. Command Function -SSE=0 DSVD mode disabled. -SSE=1 DSVD mode enabled. LINE SPEED Type: Register Format: AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during the handshaking process. Command Function S37=0 Attempt to connect at fastest common speed. S37=1 Attempt to connect at 300bps. S37=2 Attempt to connect at 300bps. S37=3 Attempt to connect at 300bps. S37=5 Attempt to connect with V.22 at 1200bps. S37=6 Attempt to connect with V.22bis at 2400bps. S37=7 Attempt to connect with V.23. S37=8 Attempt to connect with V.32 or V.32bis at 4800bps. S37=9 Attempt to connect with V.32 or V.32bis at 9600bps. S37=10 Attempt to connect with V.32bis at 12Kbps. S37=11 Attempt to connect with V.32bis at 14.4Kbps. S37=12 Attempt to connect with V.32bis at 7200bps. MODE SELECTION Type: Immediate Format: AT [cmds] #CLS=n [cmds] Description: Selects which mode the modem will operate in. Command Function #CLS=0 Modem will operate in data mode. #CLS=1 Modem will operate in fax class I mode. #CLS=2 Modem will operate in fax class II mode. #CLS=8 Modem will operate in voice mode. RPI CONFIGURATION Type: Configuration Format: AT [cmds] +Hn [cmds] Description: Configures the Rockwell Protocol Interface. Command Function +H0 RPI disabled. +H1 RPI enabled and local serial port speed set to 19.2Kbps. +H2 RPI enabled and local serial port speed set to 38.4Kbps. +H3 RPI enabled and local serial port speed set to 57.6Kbps. SPEAKERPHONE OPTIONS Type: Configuration Format: AT [cmds] #SPK=x,y,z [cmds] Description: Sets various options for speakerphone functions. Command Function x=0 Microphone enabled. x=1 Microphone disabled. x=2 Microphone enabled with maximum gain, speaker disabled. Default (y): 5 Range (y): 0 - 16 Unit (y): -2 dBm Description (y): Sets the attenuation level for speaker output in voice mode. z=0 Microphone gain set to 0 dBm. z=1 Microphone gain set to 6 dBm. z=2 Microphone gain set to 9.5 dBm. z=3 Microphone gain set to 12 dBm. TEST MODE - PTT Type: Immediate Format: AT [cmds] %TTnn [cmds] Description: Send PTT test signals for line tests. Command Function %TT00 Send DTMF digit 0. %TT01 Send DTMF digit 1. %TT02 Send DTMF digit 2. %TT03 Send DTMF digit 3. %TT04 Send DTMF digit 4. %TT05 Send DTMF digit 5. %TT06 Send DTMF digit 6. %TT07 Send DTMF digit 7. %TT08 Send DTMF digit 8. %TT09 Send DTMF digit 9. %TT0A Send DTMF digit *. %TT0B Send DTMF digit #. %TT0C Send DTMF digit A. %TT0D Send DTMF digit B. %TT0E Send DTMF digit C. %TT0F Send DTMF digit D. %TT10 Send V.21 channel 1 mark symbol. %TT11 Send V.21 channel 2 mark symbol. %TT12 Send V.23 backward channel mark symbol. %TT13 Send V.23 forward channel mark symbol. %TT15 Send V.22 originate mark symbol at 1200bps. %TT16 Send V.22bis originate mark symbol at 2400bps. %TT17 Send V.22 answer signal with guard tone if required. TEST MODE - PTT (CON'T) Command Function %TT18 Send V.22bis answer signal with guard tone if required. %TT19 Send V.21 channel 1 space symbol. %TT1A Send V.21 channel 2 space symbol. %TT1B Send V.23 backward channel space symbol. %TT1C Send V.23 forward channel space symbol. %TT20 Send V.32 9600bps carrier. %TT21 Send V.32bis 14.4Kbps carrier. %TT30 Send silence (on-line), i.e., go off-hook. %TT31 Send V.25 answer tone. %TT32 Send 1800 Hz guard tone. %TT33 Send 1300Hz V.25 calling tone. %TT34 Send 1100Hz fax calling tone. %TT40 Send V.21 channel 2 carrier. %TT41 Send V.27ter 2400bps carrier. %TT42 Send V.27ter 4800bps carrier. %TT43 Send V.29 7200bps carrier. %TT44 Send V.29 9600bps carrier. %TT45 Send V.17 7200bps long train carrier. %TT46 Send V.17 7200bps short train carrier. %TT47 Send V.17 9600bps long train carrier. %TT48 Send V.17 9600bps short train carrier. %TT49 Send V.17 12Kbps long train carrier. %TT4A Send V.17 12Kbps short train carrier. %TT4B Send V.17 14.4Kbps long train carrier. %TT4C Send V.17 14.4Kbps short train carrier. %TT5a,b,c,d,e Send V.FC carrier according to the parameters given. See the %TT6... command for information on the parameters. %TT6a,b,c,d,e Send V.34 carrier according to the parameters given. The c and e parameters have no function. Parameter Function a=0 Data rate for carrier is 2400bps for V.34 only. a=1 Data rate for carrier is 4800bps for V.34 only. a=2 Data rate for carrier is 7200bps for V.34 only. a=3 Data rate for carrier is 9600bps for V.34 only. a=4 Data rate for carrier is 12Kbps for V.34 only. a=5 Data rate for carrier is 14.4Kbps. a=6 Data rate for carrier is 16.8Kbps. a=7 Data rate for carrier is 19.2Kbps. a=8 Data rate for carrier is 21.6Kbps. a=9 Data rate for carrier is 24Kbps. a=A Data rate for carrier is 26.4Kbps. a=B Data rate for carrier is 28.8Kbps. TEST MODE - PTT (CON'T) Command Function %TT6a,b,c,d,e b=0 Baud rate for carrier is 2400 baud. b=2 Baud rate for carrier is 2800 baud. b=3 Baud rate for carrier is 3000 baud. b=4 Baud rate for carrier is 3200 baud. b=5 Baud rate for carrier is 3429 baud. c=2B Set V.FC carrier bias to -100Hz. c=3E Set V.FC carrier bias to -10Hz. c=3F Set V.FC carrier bias to -5Hz. c=40 Set V.FC carrier bias to 0Hz. c=41 Set V.FC carrier bias to +5Hz. c=42 Set V.FC carrier bias to +10Hz. c=54 Set V.FC carrier bias to +100Hz. d=0 Auxiliary channel carrier disabled. d=1 Auxiliary channel carrier enabled. e=0 Upper band edge compensation set to 0dB. e=1 Upper band edge compensation set to 1dB. e=2 Upper band edge compensation set to 2dB. e=3 Upper band edge compensation set to 3dB. e=4 Upper band edge compensation set to 4dB. e=5 Upper band edge compensation set to 5dB. e=6 Upper band edge compensation set to 6dB. e=7 Upper band edge compensation set to 7dB. e=8 Upper band edge compensation set to 8dB. e=9 Upper band edge compensation set to 9dB. e=A Upper band edge compensation set to 10dB. e=B Upper band edge compensation set to 12dB. e=C Upper band edge compensation set to 13dB. e=D Upper band edge compensation set to 14dB. e=E Upper band edge compensation set to 15dB. e=F Upper band edge compensation set to 22dB. TONE DETECTION Format: AT [cmds] #VTD=x,y,z [cmds] Default: x,y,z 3F Range: 0 - 3F (hexadecimal) Description: Sets which tones the tone detection will report. Note: The value of x sets the tone detection modes in voice transmit mode, y sets them in voice receive mode, and z sets them in voice command mode. Bit Value Function 0 0 DTMF tones are not detected. 1 DTMF tones are detected. 1 0 V.25 1300Hz calling tone is not detected. 1 V.25 1300Hz calling tone is detected. 2 0 T.30 1100Hz fax tone is not detected. 1 T.30 1100Hz fax tone is detected. 3 0 V.25/T.30 2100Hz answer tone is not detected. 1 V.25/T.30 2100Hz answer tone is detected. 4 0 Bell 2225Hz answer tone is not detected. 1 Bell 2225Hz answer tone is detected. 5 0 Call progress tones are not detected. 1 Call progress tones are detected. TONE GENERATOR - DIRECT ENTRY Type: Immediate Format: AT [cmds] #VTS=[m, n, x] Range: m 200-3000, n 200-3000, x 0-255 Unit: m 1 Hz, n 1 Hz, x .1 second Description: Generates a dual-frequency tone for duration x at frequencies m and n. TONE GENERATOR - TIMED PHONE KEYS Type: Immediate Format: AT [cmds] #VTS={a, n} Range: a 0-9, A-D, #, *; x 0-255 Unit: x .1 second Description: Generates the DTMF tone for duration x for the character a. TONE GENERATOR - PHONE KEYS Type: Immediate Format: AT [cmds] #VTS=a Range: 0-9, A-D, #, * Description: Generates the DTMF tones for the characters in the string for the duration set with +VBT. TONE GENERATOR LENGTH Format AT [cmds] #VBT=n [cmds] Default: 10 Range: 0 - 40 Unit: 0.1 second Description: Sets the length of DTMF tones that are generated. VOICE BUFFER SPACE Type: Configuration Format: AT [cmds] #VSK=n [cmds] Default: 255 Range: 0 - 255 Unit: 1 byte Description: Sets the amount of data the modem can send into the buffer after the XOFF signal is sent. VOICE DEVICE Type: Configuration Format: AT [cmds] #VLS=n [cmds] Description: Selects the I/O device for the DSP chip. Note: This modem may not support all options listed below. The #VLS? command will display the available options. Command Function #VLS=0 Telephone line and handset used for voice I/O. #VLS=1 Telephone handset used for voice I/O. #VLS=2 Internal speaker only used for voice I/O. #VLS=3 External microphone only used for voice I/O. #VLS=4 Telephone line and handset used for voice I/O; internal speaker enabled. #VLS=5 Headset used for voice I/O. #VLS=6 Speakerphone used for voice I/O. #VLS=7 Handset muted by disconnecting handset or speakerphone from telephone line. #VLS=8 Connects caller ID relay for recording of conversation over handset. #VLS=9 Connects handset (or speakerphone) to DSP chip for recording or playback. VOICE - DISPLAY BUFFER SIZE Type: Immediate Format: AT [cmds] #VBQ? [cmds] Description: Displays the size of the voice buffer. VOICE - DISPLAY COMPRESSION TYPE Type: Immediate Format: AT [cmds] #VCI? [cmds] Description: Displays the type of compression currently in use. VOICE RE-RING DETECT TIME Type: Configuration Format: AT [cmds] #VRA=n [cmds] Default: 70 Range: 0-255 Unit: 10 mS Description: Sets the maximum time the modem will wait for the remote station to ring again before it assumes that it has gone off-hook. VOICE RECEIVE Type: Immediate Format: AT [cmds] #VRX Description: Commands the modem to begin receiving voice data. VOICE RING DETECT TIME Type: Configuration Format: AT [cmds] #VRN=n [cmds] Default: 100 Range: 0 - 255 Unit: 100 mS Description: Sets the maximum time the modem will wait for the remote station to ring before it assumes that it went off-hook before it rang. VOICE SAMPLE QUALITY Type: Configuration Format: AT [cmds] #VBS=n [cmds] Description: Selects the number of bits per sample that the modem records. Note: This modem may not support all options listed below. The #VBS? command will display the available options. Command Function #VBS=2 Modem records 2 bits per sample in ADPCM encoding. #VBS=3 Modem records 3 bits per sample in ADPCM encoding. #VBS=4 Modem records 4 bits per sample in ADPCM encoding. #VBS=8 Modem records 8 bits per sample in PCM encoding. #VBS=16 Modem records 16 bits per sample in PCM encoding. VOICE SAMPLING RATE Type: Configuration Format: AT [cmds] #VSR=n [cmds] Description: Sets the sampling rate used when recording voice signals. Command Function #VSR=7200 Selects a sampling rate of 7.2KHz. #VSR=11025 Selects a sampling rate of 11.025KHz in PCM encoding only. VOICE SILENCE DETECTION Type: Configuration Format: AT [cmds] #VSD=n [cmds] Description: Selects whether the modem will use silence detection to pause recording during periods of silence. Command Function #VSD=0 Silence detection disabled. #VSD=1 Silence detection enabled. VOICE SILENCE DETECTION TIME Type: Configuration Format: AT [cmds] #VSP=n [cmds] Default: Unidentified Range: 0 - 255 Unit: .1 second Description: Sets the minimum amount of silence that the modem will detect. VOICE SILENCE DETECTION THRESHOLD Type: Configuration Format: AT [cmds] #VSS=n [cmds] Description: Sets the threshold of sensitivity that the modem uses to determine silence detection. Command Function #VSS=0 Silence detection disabled. #VSS=1 Minimum silence detection sensitivity. #VSS=2 Standard silence detection sensitivity. #VSS=3 Maximum silence detection sensitivity. VOICE TIMING MARK Type: Configuration Format: AT [cmds] #VTM=n [cmds] Description: Configures timing mark placement. Command Function #VTM=0 Timing marks disabled. #VTM=1 Timing marks enabled. VOICE TRANSMISSION LEVEL Type: Configuration Format: AT [cmds] #TL=hhhh [cmds] Default: 3FFF Range: 0000 - 7FFF Unit: Unidentified (hexadecimal) Description: Sets the transmission level for sending audio in voice mode. VOICE TRANSMIT Type: Immediate Format: AT [cmds] #VTX Description: Commands the modem to begin transmitting voice data. VOICE VOLUME LEVEL Type: Configuration Format: AT [cmds] #VGT=n [cmds] Description: Sets the volume level when playing back audio signals.