LASAT COMMUNICATIONS A/S SAFIRE 144 Card Type Modem (synchronous/asynchronous) Chipset Unidentified Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation ITU-T V.17, V.21CH2, V.27, V.29 Error Correction/Compression MNP5, MNP10, V.42, V.42bis Fax Class Class I & II Data Bus Serial [Image] CONNECTIONS Function Label Function Label DC power in CN1 Telephone line out CN3 Serial port CN2 DIAGNOSTIC LED(S) LED Color Status Condition ON Red On Power is on ON Red Off Power is off TR Red On DTR signal is high TR Red Off DTR signal is low CD Red On Carrier signal detected CD Red Off Carrier signal not detected CD Red Blinking Phone is ringing COMP Red On Modem is connected with data compression COMP Red Off Modem is not connected with data compression SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, C, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z Extended AT Commands \A, \B, \G, \J, \K, \L, \N, \W %C, %E, %F, %L, %Q Special AT Commands *H, -K, )M, -Q S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S46, S48, S82, S86, S91, S92, S95, S99 V.25bis Commands CIC, CRN, CRS, DIC, RLD, RLF Note: See MHI help file for complete information. Proprietary AT Command Set BIT-MAPPED REGISTER S40 Format AT [cmds] S40=n [cmds] Default: 107 Range: 0 - 255 Description: Controls power level and break handling; selects MNP extended services, link negotiation, and block size. Bit Value Function 0 0 MNP10 disabled. 1 MNP10 enabled. 1 0 MNP10 at 2400 and 1200bps disabled. 1 MNP10 at 2400 and 1200bps enabled. 2 0 Power level adjustment enabled. 1 Power level adjustment disabled. 5, 4, 3 000 \K0 set. 001 \K1 set. 010 \K2 set. 011 \K3 set. 100 \K4 set. 101 \K5 set. 7, 6 00 MNP block size is 64 characters. 01 MNP block size is 128 characters. 10 MNP block size is 192 characters. 11 MNP block size is 256 characters. BIT-MAPPED REGISTER S41 Format AT [cmds] S41=n [cmds] Default: 3 Range: 0 - 91 Description: Selects compression, auto-retrain and auto-fallback/fall-forward, flow control, and MNP mode. Note: Be aware that bit 6 is out of order. Bit Value Function 1, 0 00 Data compression disabled. 01 MNP5 enabled. 10 V.42bis enabled. 11 MNP5 and V.42bis enabled. 6, 2 00 Auto-retrain disabled. 01 Auto-retrain enabled. 10 Auto-fallback/fall-forward enabled. 3 0 Flow control disabled. 1 Flow control enabled. 4 0 Stream mode for MNP. 1 Block mode for MNP. 5 0 Not used. BIT-MAPPED REGISTER S80 Format: AT [cmds] S80=n [cmds] Default: 1 Range: 1 - 225 Description: Selects a command set and controls callback security and remote configuration. Bit Value Function 4 - 0 00001 Not used. 5 0 AT command set enabled. 1 V.25bis command set enabled. 6 0 Remote configuration disabled. 1 Remote configuration enabled. 7 0 Callback security disabled. 1 Callback security enabled. CALLBACK PASSWORD Type: Configuration Format: AT [cmds] *Pn:xxxxx:<#> Description: Changes connection password number n. n must be between 0 and 4. The password must be between 6 and 12 characters. If no callback number is supplied, the modem will check for a password but will not perform a callback. CALLBACK - DISPLAY PASSWORD TABLE Type: Immediate Format: AT [cmds] *L [cmds] Description: Displays the list of connection passwords. COUNTRY CODE Type: Configuration Format: AT [cmds] *NCn [cmds] Description: Sets the factory defaults according to the country specified. The next power-up or ATZ command will reset the modem to the appropriate defaults. Command Function *NC1 Set country code for Austria. *NC2 Set country code for Belgium. *NC3 Set country code for Denmark. *NC4 Set country code for Finland. *NC5 Set country code for France. *NC6 Set country code for Germany. *NC7 Set country code for Ireland. *NC8 Set country code for Italy. *NC9 Set country code for Luxembourg. *NC10 Set country code for the Netherlands. *NC11 Set country code for Norway. *NC12 Set country code for Portugal. *NC13 Set country code for Spain. *NC14 Set country code for Sweden. *NC15 Set country code for Switzerland. *NC16 Set country code for Great Britain. *NC20 Set country code for Canada. *NC21 Set country code for Mexico. *NC22 Set country code for the United States. *NC40 Set country code for Australia. *NC43 Set country code for Japan. *NC47 Set country code for Singapore. *NC48 Set country code for New Zealand. DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DJ MNP10 link will be negotiated at 1200bps for this call. DK MNP10 power level adjustment enabled for this call. DL Re-dial last number. DP Pulse dialing enabled. DS=n Dial stored telephone number n. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY BLACKLIST NUMBERS Type: Immediate Format: AT [cmds] *B [cmds] Description: Displays the list of all the numbers on the blacklist and their statuses. DISPLAY DELAYED NUMBERS Type: Immediate Format: AT [cmds] *D [cmds] Description: Displays the list of all delayed numbers and their statuses. DISPLAY CONFIGURATION AND STATISTICS Type: Immediate Format: AT [cmds] \S [cmds] Description: Displays the settings of all commands. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and reports ROM checksum. I3 Displays firmware revision. I4 Displays production identification. I5 Displays country code. I6 Displays production identification. DISPLAY STORED NUMBERS Type: Immediate Format: AT [cmds] \F [cmds] Description: Displays all stored telephone numbers. LINE SPEED Type: Register Format: AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during the handshaking process. Command Function S37=0 Attempt to connect at fastest common speed. S37=1 Set speed to 300bps. S37=2 Set speed to 300bps. S37=3 Set speed to 300bps. S37=5 Set speed to 1200bps. S37=6 Set speed to 2400bps. S37=7 Attempt to connect with V.23. S37=8 Set speed to 4800bps. S37=9 Set speed to 9600bps. S37=10 Set speed to 12Kbps. S37=11 Set speed to 14.4Kbps. S37=12 Set speed to 7200bps. PROTOCOL/SPEED Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects the protocol and speed the modem will attempt to connect at. Command Function F0 Auto-detect the highest common connect speed. F1 Select V.21 or Bell 103 at 300bps speed. F3 Select V.23 at 75/1200bps speed. F4 Select V.22 or Bell 212A at 1200bps speed. F5 Select V.22bis at 2400bps speed. F6 Select V.32 or V.32bis at 4800bps speed. F7 Select V.32bis at 7200bps speed. F8 Select V.32bis or V.32 at 9600bps speed. F9 Select V.32bis at 12Kbps speed. F10 Select V.32bis at 14.4Kbps speed. TEST MODE - PTT Type: Immediate Format: AT [cmds] %TTnn [cmds] Description: Send PTT test signals for line tests. Command Function %TT00 Send DTMF digit 0. %TT01 Send DTMF digit 1. %TT02 Send DTMF digit 2. %TT03 Send DTMF digit 3. %TT04 Send DTMF digit 4. %TT05 Send DTMF digit 5. %TT06 Send DTMF digit 6. %TT07 Send DTMF digit 7. %TT08 Send DTMF digit 8. %TT09 Send DTMF digit 9. %TT0A Send DTMF digit *. %TT0B Send DTMF digit A. %TT0C Send DTMF digit B. %TT0D Send DTMF digit C. %TT0E Send DTMF digit #. %TT0F Send DTMF digit D. %TT10 Send V.21 channel 1 mark symbol. %TT11 Send V.21 channel 2 mark symbol. %TT12 Send V.23 backward channel mark symbol. %TT13 Send V.23 forward channel mark symbol. %TT14 Send V.22 originate mark symbol at 600bps. %TT15 Send V.22 originate mark symbol at 1200bps. %TT16 Send V.22bis originate mark symbol at 2400bps. %TT17 Send V.22 answer signal with guard tone if required. TEST MODE - PTT (CON'T) Command Function %TT18 Send V.22bis answer signal with guard tone if required. %TT19 Send V.21 channel 1 space symbol. %TT1A Send V.21 channel 2 space symbol. %TT1B Send V.23 backward channel space symbol. %TT1C Send V.23 forward channel space symbol. %TT1D Send V.27ter carrier. %TT1E Send V.29 carrier. %TT20 Send V.32 9600bps. %TT21 Send V.32bis 14.4Kbps. %TT22 Send V.17 14.4Kbps. %TT30 Send silence (on-line), i.e., go off-hook. %TT31 Send V.25 answer tone. %TT32 Send 1800 Hz guard tone. %TT33 Send 1300Hz V.25 calling tone. %TT34 Send 1100Hz fax calling tone. REMOTE CONFIGURATION CHARACTER Type: Register Format: AT [cmds] S202=n [cmds] Default: 170 Range: 0 - 255 Unit: 1 ASCII character Description: Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested. Values over 127 disables the remote configuration character. REMOTE CONFIGURATION EXIT Type: Immediate Format: AT [cmds] *E [cmds] Description: Exits remote configuration mode. REMOTE CONFIGURATION SECURITY - PASSWORD SELECTION Type: Configuration Format: AT [cmds] *C Description: Changes the password for remote configuration. The user will be prompted to enter the old and new passwords. Passwords must be exactly five characters, case insensitive. REMOTE CONFIGURATION REQUEST Type: Immediate Format: AT [cmds] *R [cmds] Description: Requests to begin a remote configuration session with the remote modem. Note: The same function may be accomplished by sending the remote configuration character four times within the guard time set by register S202. Proprietary V.25bis Command Set AT COMMAND Type: Immediate Format: CNL[cmds] Description: Executes an AT command string. The AT should not be included. CALL REQUESTED NUMBER WITH IDENTIFICATION Type: Immediate Format: CRI<#>;xxxx Description: Dials the number given; it will ignore spaces and hyphens in the string; if the string is more than fifty characters long, a result of INV will be returned. The xxxx parameter is ignored. REQUEST LISTED NUMBERS Type: Immediate Format: RLN Description: Requests the modem to return the list of stored numbers; if no numbers are stored, the modem will return LSN.