BEST DATA PRODUCTS, INC.

SMART ONE 2834F, SMART ONE 2834V, SMART ONE 2834VP

Card Type                    Modem (asynchronous)
Chipset                      Unidentified
I/O Options                  Voice (except on Smart One 2834F)
Maximum Data Rate            28.8Kbps
Maximum Fax Rate             14.4Kbps
Data Bus                     8-bit ISA
Fax Class                    Class I & II
Data Modulation              Bell 103A/212A

                             ITU-T V.21, V.22, V.22bis, V.23, V.32,
                             V.32bis, V.34

                             Rockwell V.FC
Fax Modulation               ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression MNP5, MNP10EC, V.42, V.42bis

[Image]

                                CONNECTIONS

          Function             Label           Function             Label

  Line out                     CN1     Line in                      CN2

                 INTERRUPT SELECTION

  Setting    SW1/1      SW1/2      SW1/3      SW1/4

   IRQ3        On        Off        Off        Off

   IRQ4       Off         On        Off        Off

   IRQ5       Off        Off        On         Off

   IRQ7       Off        Off        Off        On

         SERIAL PORT ADDRESS SELECTION

    Setting          SW1/5          SW1/6

  3F8h (COM1:)        On              On

  2F8h (COM2:)        On             Off

  3E8h (COM3:)        Off             On

  2E8h (COM4:)        Off            Off

                        SUPPORTED STANDARD COMMANDS

                             Basic AT Commands

  +++, ‘comma’, A/

  A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

  &C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

                           Extended AT Commands

  \A, \B, \G, \K, \N

  %C, %E, %L, %Q

                            Special AT Commands

  #CID, +MS

                                S-Registers

  S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18,
  S21, S22, S23, S24, S25, S26

  S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82,
  S86, S91, S92, S95

            Note: See MHI documentation for complete information.

     UNIDENTIFIED COMMANDS

    Command         Default

      S37              0

      S201       Unidentified

                         Proprietary AT Command Set

                            DISPLAY INFORMATION

  Type:          Immediate

  Format:        AT [cmds] In [cmds]

  Description:   Displays information requested about the modem.

    Command                              Function

       I0        Displays product identification code.

       I1        Displays ROM checksum.

       I3        Displays firmware model, revision, and interface.

       I5        Displays country code.

       I6        Displays data pump model and revision.

       I7        Displays the DAA code.

                       MNP10 POWER LEVEL ADJUSTMENT

  Type:                  Configuration

  Format:                AT [cmds] )Mn [cmds]

  Description:           Controls automatic transmit power level
                         adjustment during MNP 10 link negotiation.

        Command                              Function

          )M0            Power level adjustment disabled.

          )M1            Power level adjustment enabled.

          )M2            Power level adjustment enabled; S40 bit 2 and
                         S201 bit 6 are reset to their default settings.

                               MNP10EC MODE

  Type:                  Configuration

  Format:                AT [cmds] -SEC=n [cmds]

  Description:           Selects whether the modem will attempt to use
                         MNP10EC mode during the handshaking sequence.

        Command                              Function

         -SEC=0           MNP10EC handshaking disabled unless a V.34
                          connection is attempted via a cellular line.

         -SEC=1           MNP10EC handshaking enabled.