BANKSIA TECHNOLOGY PTY, LTD. PRO 144 Card Type Fax, Modem (synchronous/asynchronous) Chip Set Unidentified Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus External Fax Class Class I Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.27ter, V.29 Error Correction/Compression MNP5, MNP10, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Auxiliary port CN1 DC power CN4 Line out CN2 Power switch SW1 RS-232/422 CN3 USER CONFIGURABLE SETTINGS Setting Label Position DTR signal ignored SW1/1 On DTR signal normal SW1/1 Off DCD and DSR forced high SW1/2 On DCD and DSR normal SW1/2 Off Echo disabled SW1/3 On Echo enabled SW1/3 Off Result codes disabled SW1/4 On Result codes enabled SW1/4 Off Leased-line operation SW1/5 On Switched line operation SW1/5 Off Auto-answer enabled on 2nd ring SW1/6 On Auto-answer disabled on 2nd ring SW1/6 Off Synchronous mode 2 enabled SW1/7 On Synchronous mode 2 disabled SW1/7 Off Dumb mode SW1/8 On Smart mode SW1/8 Off Flow control to XON/XOFF enabled SW2/1 On Flow control to XON/XOFF disabled SW2/1 Off V.25bis command set synchronous HDLC (NRZI) SW2/2 On enabled V.25bis command set synchronous HDLC (NRZI) SW2/2 Off disabled Factory configured - DO NOT ALTER SW2/5 Unidentified Factory configured - DO NOT ALTER SW2/6 Unidentified Factory configured - DO NOT ALTER SW2/7 Unidentified Factory defaults loaded up on power-up SW2/8 On Do no force factory defaults on power-up SW2/8 Off Factory configured - DO NOT ALTER LK2 Unidentified AUXILIARY PORT Setting LK1 LK3 LK4 LK5 LK6 LK7 LK8 PSTN Pins 2 Closed Closed Closed Open Closed Open & 3 closed Leased Pins 1 Open Closed Open Closed Closed Closed line & 2 closed MODULATION SELECTION Setting SW2/3 SW2/4 factory/stored setting Off Off 14400 carrier Off On 9600 carrier On Off 2400 carrier On On SUPPORTED COMMAND SET Basic AT Commands AT, ‘Comma’ A, B, E, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z &C, &D, &G, &L, &R, &S, &V, &W, &X, &Y, &Z Extended AT Commands \B, \G, \J, \V, \Y, \Z Special Commands *H, )M S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S25, S26, S36 S37, S38 Note: See MHI Help file for full command documentation. Proprietary AT Command Set ACKNOWLEDGMENT TIMER (T401) Type: Configuration Format: AT [cmds] %Wn [cmds] Default: Unidentified Range: 0-63 Unit: Unidentified Description: Wait to retransmit time out Note: T401 = 4 seconds + n x 100ms. Exception when in MNP mode: If n=0 use Microcom timers. If n=63 use ITU-T V42 Annex A timers. ANSWER LOGON SEQUENCE Type: Register Format: AT [cmds] S34=n [cmds] Default: 0 Range: 0, 128-137 Unit: Unidentified Description: Controls answer logon sequence Note: If ATS34=0, then no logon in answer mode AUTO-RELIABLE FALLBACK CHARACTER Type: Configuration Format: AT [cmds] S46=n [cmds] Default: 13 Range: 0-127 Unit: ASCII Description: Sets the character used as the auto-reliable fallback character; %A0 will disable this function. AUTO-RETRAIN Type: Configuration Format: AT [cmds] &En [cmds] Description: Controls auto-retrain mode Command Function &E0 Auto-retrain disabled &E1 Auto-retrain enabled BIT-MAPPED REGISTER S23 Format AT [cmds] S23=n [cmds] Default: Unidentified Range: 0-189 Unit: Bit-mapped Description: Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone. Bit Value Function 0 0 Remote digital loopback denied 1 Remote digital loopback allowed 3 - 1 000 Sets serial port speed to 0-300bps 001 Sets serial port speed to 600bps 010 Sets serial port speed to 1200bps 011 Sets serial port speed to 2400bps 100 Sets serial port speed to 4800bps 101 Sets serial port speed to 9600bps 110 Sets serial port speed to 19200bps 111 Sets serial port speed to 38400bps 5, 4 00 Parity even 01 Space Parity 10 Parity odd 11 Mark or No Parity 7, 6 00 Guard tone disabled 01 Guard tone 550Hz enabled 10 Guard tone 1800Hz enabled BIT-MAPPED REGISTER S24 Format: AT [cmds] S24=n [cmds] Default: 143 Range: 0-255 Description: Controls error control fallback character, error control buffer, data compression, auto-mode detection, extended result code, and lock serial port speed. Bit Value Function 0 0 No fallback character 1 Enable fallback character in S46 1 0 Do not buffer data 1 Buffer data 2 0 Data compression disabled 1 Data compression enabled 4, 3 00 S37 speed 01 Optimum speed up to DTE if ATS37=255 10 Optimum speed if ATS37=255, except V.34 is disabled 6, 5 00 Extended result codes enabled 01 Hayes extended result codes enabled 10 Microcom extended result codes enabled 7 0 Serial speed locked 1 Serial speed follows connect speed BIT-MAPPED REGISTER S27 Format AT [cmds] S27=n [cmds] Default: 10 Range: 0-111 Unit: Bit-mapped Description: Selects synchronous/asynchronous mode, line type, clock source, and ITU-T/Bell modes. Bit Value Function 3, 1, 000 Asynchronous direct mode enabled 0 001 Synchronous mode 1 010 Synchronous mode 2 011 Synchronous mode 3 100 Direct mode 101 Error correction mode 110 V.42/MNP error correction mode 111 V.42 error correction mode only 2 0 Switched line 1 Leased line 5, 4 00 Local modem generates transmit clock source 01 Local DTE generates transmit clock source 10 Remote DCE/DTE generates transmit clock source 6 0 ITU/T mode 1 Bell mode BIT-MAPPED REGISTER S28 Format: AT [cmds] S28=n [cmds] Default: 8 Range: 0-255 Description: Controls maximum block size, V.42 detection period (T4ØØ) in 5Ø milliseconds increments, and ODP/ADP Bit Value Function 1, 0 00 64 bytes 01 128 bytes 10 192 bytes 11 256 bytes 6 - 2 00000 Infinite time for detection ….to…. ….to…. 10000 .8 seconds ….to…. ….to…. 11111 7.75 seconds 7 0 Disable ODP/ADP when initiating a reliable V.42 handshake 1 Enable ODP/ADP when initiating a reliable V.42 handshake BIT-MAPPED REGISTER S29 Format: AT [cmds] S29=n [cmds] Default: 0 Range: 0-255 Description: Controls V.42 acknowledgment timer (T4Ø1), V.42 frame check sequence, and V.42 selective reject Bit Value Function 5 - 0 000000 4 seconds 000001 4.1 .…to…. ….to…. 111111 10.3 seconds 6 0 Always use CRC-16 1 Attempt use if CRC-32 7 0 Disable V.42 selective reject 1 Enable V.42 selective reject BIT-MAPPED REGISTER S30 Format: AT [cmds] S30=n [cmds] Default: 15 Range: 0-255 Description: Controls V.42 windows size Negative ADP, asynchronous MNP2, and remote loopback test Bit Value Function 4 - 0 00000 Not used 00001 1 packet .…to…. ….to…. 01111 15 packets .…to…. .…to…. 11111 31 packets 5 0 Disable negative ADP 1 Enable negative ADP 6 0 Do not force asynchronous MNP2 1 Force asynchronous MNP2 7 0 Ignore loopback frame received from remote 1 Process loopback frame received from remote BIT-MAPPED REGISTER S31 Format: AT [cmds] S31=n [cmds] Default: 0 Range: 0-159 Description: Controls V.25 bis selection, synchronous mode V.13, abort, DTE Autobauding, and V.25 bis mode. Bit Value Function 1, 0 00 Asynchronous V.25 01 Bisync V.25 bis NRZ 10 HDLC V.25 bis NRZ 11 HDLC V.25 bis NRZI 2 0 Disable Synchronous mode V.13 1 Enable Synchronous mode V.13 3 0 Ignore keyboard abort on answer disabled 1 Ignore keyboard abort on answer enabled 4 0 Enable DTE Autobauding 1 Disable DTE Autobauding 6, 5 00 Not used 7 0 AT commands enabled 1 V.25bis enabled as per bits 1,Ø BIT-MAPPED REGISTER S32 Format: AT [cmds] S32=n [cmds] Default: 0 Range: 0-255 Description: Controls encryption mode, MNP extended services, power level adjustment, MNP10 - link negotiation, and MNP1Ø selection. Bit Value Function 1, 0 00 No encryption 01 Force V.42bis encryption 10 Not used 11 Not used 3, 2 00 MNP Extended Services disabled 01 MNP Extended Services enabled 10 MNP Extended Services enabled without MNP indication during the answer detect phase 4 0 Power level adjustment disabled 1 Power level adjustment enabled 6, 5 00 Link will be negotiated at highest possible speed 01 Link will be negotiated at 1200bps 10 Link will be negotiated at 4800bps 7 0 MNP10 enabled 1 MNP10 disabled BIT-MAPPED REGISTER S39 Format: AT [cmds] S39=n [cmds] Default: 128 Range: 0-252 Description: Controls, DTE rate at 230.4Kbps, DTE rate at 115.2Kbps, break handling, EIA loopback test, and auto retrain Bit Value Function 1, 0 00 Not used 2 0 DTE rate is according to bits 1-3 of S23 or bit 3 of S39 1 DTE rate fixed at 23Ø4ØØ bps 3 0 DTE rate is according to bits 1-3 of S23 or bit 2 of S39 1 DTE rate fixed at 1152ØØ bps 5, 4 00 Break sent in sequence with received data 10 Break sent immediately to DTE 11 Buffers cleared, break sent to DTE 6 0 Disabled EIA loopback test 1 Enabled EIA loopback test 7 0 Auto retrain disabled 1 Auto retrain enabled BIT-MAPPED REGISTER S49 Format: AT [cmds] S49=n [cmds] Default: Unidentified Range: 0-255 Description: Controls flow control, compromise equalizer value, smart/dumb mode, and, compromise equalizer. Bit Value Function 4 - 0 00000 Flow control disabled 00011 Hardware flow control 00100 DCE to DTE, bi-directional flow control 01000 DCE to DTE, unidirectional flow control 01100 DCE to DTE, bi-directional, transparent flow control 10000 DCE to remote modem, bi-directional flow 10100 control DTE to DCE to remote modem bi-directional flow control 5 0 3 dB when compromise equalizer enabled 1 6 dB when compromise equalizer enabled 6 0 Smart mode 1 Dumb mode 7 0 Compromise equalizer enabled 1 Compromise equalizer disabled BREAK MODE Type: Configuration Format: AT [cmds] &In [cmds] Description: Controls how the modem handles break conditions on the DTE interface Command Function &IØ Break sent in sequence with received data &I1 Break sent immediately to DTE &I2 Buffers cleared, break sent to DTE BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Break from DTE \K0 Online command mode enabled, send no break to remote modem \K1 Break sent to remote modem and buffers cleared \K2 Online command mode enabled, send no break to remote modem \K3 Send break to remote modem immediately \K4 Online command mode enabled, send no break to remote modem \K5 Send break with transmitted data BUFFERED DATA ON HANG-UP Type: Configuration Format: AT [cmds] %Dn [cmds] Default: Unidentified Range: 0-255 Unit: 1 second Description: Wait for receive buffer to be sent to DTE before hanging up Command Function %DØ Hang up without clearing buffer COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Qn [cmds] Description: Selects communications mode options Command Mode &Q0 Asynchronous mode enabled &Q1 Synchronous mode 1 enabled &Q2 Synchronous mode 2 enabled &Q3 Synchronous mode 3 enabled &Q4 Asynchronous direct mode &Q5 MNP Error correction mode &Q6 V.42/MNP error correction mode &Q7 V.42 error correction mode only CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 MNP auto-reliable mode enabled \N6 Reliable mode enabled \N7 Auto-reliable mode enabled DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Modifier Function J Link will be negotiated at 1200bps, AT*H1 command K Power level adjustment enabled, AT)M1 command P Pulse dialing enabled S=n Dial stored telephone number n T Tone dialing enabled/Pulse dialing disabled , Dialing paused for amount of time specified in S8 register DIAL ATTEMPTS Type: Register Format: AT [cmds] S41=n [cmds] Default: 0 Range: 0-10 Unit: 1 attempt Description: Controls the number of time the modem will redial DTE AUTOBAUDING Type: Configuration Format: AT [cmds] %Bn [cmds] Description: When AT%B1 is set, the modem will only respond to commands at the same port (DTE) speed Note: This command can be used to lock the port speed, see AT\J in the MHI Help file. Command Function %B0 DTE autobauding enabled %B1 DTE autobauding disabled DTE SPEED - DATA MODE Type: Configuration Format: AT [cmds] &Bn [cmds] Description: Controls DTE speed during data mode Command Function &B0 DTE speed follows connect speed &B1 DTE speed equals last AT command speed or the default value on power up ERROR CONTROL BUFFER Type: Configuration Format: AT [cmds] &On [cmds] Description: Controls how buffering is performed during the error control negotiation period Note: This command affects how data received is processed by the DCE Command Function &O0 Discard data received during negotiation &O1 Buffer data received during negotiation. Data will be sent to the DTE after the connect result code, if error control negotiation fails. ERROR CORRECTION Type: Read-only Format: AT [cmds] S44? [cmds] Description: Displays which error correction method is in use Value Meaning 0 Error correction disabled 2 MNP class 2 enabled 3 MNP class 3 enabled 4 MNP class 4 enabled 5 MNP class 5 enabled 6 V.42 enabled 7 V.42bis enabled FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &FØ V.42 factory defaults &F1 MNP factory defaults &F2 Basic asynchronous operation defaults FLASH MEMORY DOWNLOAD Type: Immediate Format: AT [cmds] %FLOAD [cmds] Description: Retrieve upgrade code to modem through serial port FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 Local RTS/CTS flow control enabled &K4 Local XON/XOFF flow control enabled &K8 Unidirectional Software flow control enabled &K12 Software flow control - XON/XOFF enabled &K16 Software - Internal XON/XOFF flow control enabled &K20 Software - Local XON/XOFF flow control enabled FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S48=n [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S47=n [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON INACTIVITY TIMER Type: Register Format: AT [cmds] S40=n [cmds] Default: 0 Range: 0-255 Unit: 1 minute Description: Sets the length of time that the modem does not receive information before it disconnects; S90=0 will disable. INGORE KEYBOARD ABORT DURING ANSWER MODE Type: Configuration Format: AT [cmds] %Qn [cmds] Description: Controls the modem to ignore any data sent to the modem while it is in answer mode Command Function %Q0 Keyboard abort disabled %Q1 Keyboard abort enabled LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %Ln [cmds] Description: Returns a value which indicates the received line signal level Command Function %L0 Reports signal level in dB %L1 Reports data pump line status REDIAL ATTEMPTS ON LINE LOSS Type: Configuration Format: AT [cmds] {An [cmds] Default: Unidentified Range: 0-3 Unit: 1 attempt Description: Number of attempts to attempt to reconnect if line drops by 1 minute intervals Note: ATS15=0 - No re-dial REDIAL ATTEMPTS ON LINE LOSS Type: Register Format: AT [cmds] S15=n [cmds] Default: Unidentified Range: 0-3 Unit: 1 attempt Description: Number of attempts to attempt to reconnect if line drops by 1 minute intervals Note: If the re-dial is aborted by a key-press then no further re-dials are attempted. REASON FOR DISCONNECTION Type: Read-only Format: AT [cmds] S45? [cmds] Description: Displays why the modem disconnected from the link Value Meaning 0 Lost carrier 1 User interrupt 2 Training failure 3 Retrain failure 4 Inactivity time out 5 Long space disconnect 6 Negotiation failure REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports ROM checksum. The report is displayed as three hexadecimal digits. I2 Tests and reports ROM checksum, returns ‘OK’ or ‘ERROR’ I3 Reports firmware revision number I4 Reports ASCII string test I5 Reports data pump chipset revision SMART/DUMB MODE Type: Configuration Format: AT [cmds] *Dn [cmds] Description: Select between smart mode and dumb mode Command Function *D0 Smart mode enabled *D1 Dumb mode enabled TRANSMISSION LEVEL Type: Register Format: AT [cmds] S35=n [cmds] Default: 10 Range: 0-20 Unit: -1 dBm Description: Sets the signal level for transmission TRANSMISSION LEVEL - CELLULAR Type: Register Format: AT [cmds] S33=n [cmds] Default: 9 Range: 0-20 Unit: -1 dBm Description: Sets the signal level for transmission while in cellular mode V.25bis SELECTION Type: Configuration Format: AT [cmds] %Vn [cmds] Description: Sets the V.25bis speed as per S23 bits 3, 2, 1 and S39 bits 3,2 Command Function %VØ AT command set %V1 V.25bis command set asynchronous %V2 V.25bis command set synchronous BSC %V3 V.25bis command set synchronous HDLC (NRZ) %V4 V.25bis command set synchronous HDLC (NRZI)