PIICEON, INC. DISPATCHER 805-3400 Card Type Modem (asynchronous) Chipset Rockwell Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Bus Compaq communications bus Fax Class Class I & II Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis, V.34 Fax Modulation ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, MNP10, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Line out CN1 Compaq communications bus CN3 Line in CN2 SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, C, E, H, L, M, N, O, Q, V, W, X, Y, Z &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \G, \J, \L, \W %C, %F, %L, %Q S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, S16, S18, S21, S22, S23, S24, S25, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95, S201 Special AT Commands -K, -Q, *H, )M, @M, :E, #CID Note: See MHI help file for full command documentation. Proprietary AT Command Set BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K0 Online command mode enabled, do not send break to remote modem. \K1 Break sent to remote modem and buffered cleared. \K2 Online command mode enabled, do not send break to remote modem. \K3 Send break to remote modem immediately. \K4 Online command mode enabled, do not send break to remote modem. \K5 Send break with transmitted data. CALLBACK Type: Configuration Format: AT [cmds] *Pn:xxxx:<#> Description: Stores the information for callback number n. When enabled, the modem will call back the phone number indicated and request the matching password. CELLULAR DRIVER DOWNLOAD Type: Immediate Format: AT [cmds] ^C2 Description: Initiates an ASCII transfer of a new cellular phone driver. CELLULAR DRIVER INFORMATION Type: Immediate Format: AT [cmds] ^I [cmds] Description: Displays information about the currently loaded cellular phone driver. CELLULAR PHONE STATUS Type: Immediate Format: AT [cmds] ^T6 [cmds] Description: Displays the current status of the connected cellular phone. Bit Value Function 0 0 Cellular phone is not receiving an incoming call. 1 Cellular phone is receiving an incoming call. 1 0 Cellular phone is not in use. 1 Cellular phone is in use. 2 0 Cellular phone is not locked. 1 Cellular phone is locked. 3 0 Cellular service present. 1 Cellular service not present. 4 0 Cellular phone is off. 1 Cellular phone is on. 5 0 Cellular driver is not initialized. 1 Cellular driver is initialized. 6 0 Not used. 7 0 Cellular cable not detected. 1 Cellular cable detected. CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will connect with. Command Function \N0 Modem will connect in normal mode. \N1 Modem will connect in normal mode. \N2 Modem will attempt V.42bis mode, then MNP mode, then hang up. \N3 Modem will attempt V.42bis mode, then MNP mode, then normal mode. \N4 Modem will attempt V.42bis mode, then hang up. \N5 Modem will attempt MNP mode, then hang up. DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string. Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DJ MNP10 link will be negotiated at 1200bps for this call. DK MNP10 power level adjustment enabled for this call. DL Re-dial last number. DP Dial following digits in pulse mode. DS=n Dial stored telephone number n. DT Dial following digits in tone mode. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D"WXY" Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D& Wait for AT&T credit card ("bong") tone detection function enabled. Waits for bong tone for amount of time specified by the S7 command. D$ Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. D^ Toggles calling tone on or off for this call. D> Sends grounding pulse on EARTH relay line. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY STORED NUMBERS Type: Immediate Format: AT [cmds] \F [cmds] Description: Displays all stored numbers. MODULATION SELECTION Type: Configuration Format: AT [cmds] +DMS=x,y,z,a [cmds] Description: Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected. Command Function x=0 Set protocol to V.21. x=1 Set protocol to V.22. x=2 Set protocol to V.22bis. x=3 Set protocol to V.23. x=9 Set protocol to V.32. x=10 Set protocol to V.32bis. x=11 Set protocol to V.34. x=64 Set protocol to Bell 103. x=69 Set protocol to Bell 212A. y=0 Automode disabled. y=1 Auto-detect highest speed enabled y=2 Unidentified. z, a=300 Set minimum or maximum transfer rate at 300bps, respectively. z, a=1200 Set minimum or maximum transfer rate at 1200bps, respectively. z, a=2400 Set minimum or maximum transfer rate at 2400bps, respectively. z, a=4800 Set minimum or maximum transfer rate at 4800bps, respectively. z, a=7200 Set minimum or maximum transfer rate at 7200bps, respectively. z, a=9600 Set minimum or maximum transfer rate at 9600bps, respectively. z, a=12000 Set minimum or maximum transfer rate at 12000bps, respectively. z, a=14400 Set minimum or maximum transfer rate at 14400bps, respectively. z, a=16800 Set minimum or maximum transfer rate at 16800bps, respectively. z, a=19200 Set minimum or maximum transfer rate at 19200bps, respectively. z, a=21600 Set minimum or maximum transfer rate at 21600bps, respectively. z, a=24000 Set minimum or maximum transfer rate at 24000bps, respectively. z, a=26400 Set minimum or maximum transfer rate at 26400bps, respectively. z, a=28800 Set minimum or maximum transfer rate at 28800bps, respectively. REMOTE CONFIGURATION END Type: Configuration Format: AT [cmds] *E [cmds] Description: Ends the current remote configuration session. REMOTE CONFIGURATION PASSWORD Type: Configuration Format: AT [cmds] *Cxxxx [cmds] Description: Stores the password that must be sent by a remote modem to enter a remote configuration session on the local modem. REMOTE CONFIGURATION REQUEST Type: Configuration Format: AT [cmds] *Rn [cmds] Description: Requests the remote modem to start a remote configuration session. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested. Command Function I0 Reports modem model and speed. I1 Reports ROM checksum. I2 Tests and reports ROM checksum. I3 Reports firmware revision. I4 Reports OEM identifer. I5 Reports country code. I6 Reports data pump and ROM revision.