MOTOROLA, INC. VANGUARD 305 Card Type Frame relay adapter, Token Ring router Processor Motorola 68360 Processor Speed Unidentified Chip Set Unidentified Maximum Onboard Memory 8MB DRAM/2MB Flash RAM I/O Options Serial ports (3) Network Transfer Rate 4Mbps/16Mbps DSU Transfer Rate 56Kbps ISDN Transfer Rate 64Kbps x 2 DSU Protocol DDS ISDN Protocol Unidentified Switch Type Unidentified Data Bus External Topology Linear Bus/Star Wiring Type Unshielded twisted pair Shielded twisted pair Boot ROM Not available [Image] CONNECTIONS Function Label Function Label Reset button BT1 CTP connector or ISDN CN4 connector (port 4) Lamp test button BT2 V.24 serial port CN5 (port 3) Header for daughtercard CN1 V.11, V.24, V.35, or CN6 V.36 serial port (port 2) Unshielded twisted pair CN2 120VAC power CN7 connector Shielded twisted pair CN3 Power switch SW3 connector Note:When LED4 is on, press the lamp test button to reset it. Port 1 is the daughterboard. USER CONFIGURABLE SETTINGS Setting Label Position » Port 2 pin 22 used for ring SW1/1 Off indicator Port 2 pin 22 used to enter test SW1/1 On mode in DCE mode, ring indicator in DTE mode » Port 2 pin 25 used for test mode SW1/2 Off indicator Port 2 pin 25 used for test mode SW1/2 On indicator for DCE mode, busy out for DTE mode » Port 3 pin 22 used for ring SW1/3 Off indicator Port 3 pin 22 used to enter test SW1/3 On mode in DCE mode, ring indicator in DTE mode » Port 3 is normal serial port SW1/4 Off Port 3 is the PAD port (forces SW1/4 On serial configuration to 9600bps, no parity, 8 data bits, 1 stop bit) » Factory configured - do not alter SW1/5 Off » Normal operation SW1/6 Off Reset entire configuration to SW1/6 On factory defaults Note:To use SW1/6, power up the adapter, turn SW1/6 on, press the reset button, and turn SW1/6 back off again. DRAM Setting On Board S1 4MB 4MB None 8MB 4MB (1) 4MB x 9 PORT 2 TYPE Setting SW2/1 SW2/2 SW2/3 SW2/4 SW2/5 SW2/6 V.11 DTE Off Off Off Off Off On V.11 DCE Off Off Off Off Off On V.24 DTE On On On On On Off V.24 DCE On On On On On Off V.35 DTE Off Off Off Off Off On V.35 DCE Off Off Off Off Off On V.36 DTE Off Off Off Off Off On V.36 DCE Off Off Off Off Off On DSU Off Off Off Off Off On PORT 2 TYPE (CON’T) Setting SW2/7 SW2/8 U1 V.11 DTE On On V.11 module in position 1 V.11 DCE On On V.11 module in position 2 V.24 DTE Off Off V.24 module in position 1 V.24 DCE Off Off V.24 module in position 2 V.35 DTE On On V.35 module in position 1 V.35 DCE On On V.35 module in position 2 V.36 DTE On On V.36 module in position 1 V.36 DCE On On V.36 module in position 2 DSU On On DSU module in position 1 DIAGNOSTIC LED(S) (RESET AND POWER-UP) LED1 LED3 Condition Blinking Off Adapter is loading software into DRAM from flash RAM Off Blinking Adapter is performing self-test Off Off Adapter is initializing configuration On Off Adapter is ready Off On Self-test failed Note:On reset or power-up, the LEDs should go through, in order, the first four actions shown above. If the adapter proceeds immediately to the fourth action, the code in the firmware is invalid. DIAGNOSTIC LED(S) LED Color Status Condition LED1 Green On Software is running LED1 Green Off Software not running LED1 Green Blinking Software is downloading or card is booting LED2 Green On Power is on LED2 Green Off Power is off LED3 Red On Test failed LED3 Red Off No test in progress or test passed LED3 Red Blinking Test in progress LED4 Red On Processor did not reset timer in set time LED4 Red Off Normal operation LED5 Yellow On Card is transmitting MARK signal to port 1 LED5 Yellow Off Card is transmitting SPACE signal to port 1 LED6 Yellow On Card is receiving MARK signal from port 1 LED6 Yellow Off Card is receiving SPACE signal from port 1 LED7 Yellow On Card is transmitting MARK signal to port 2 LED7 Yellow Off Card is transmitting SPACE signal to port 2 LED8 Yellow On Card is receiving MARK signal from port 2 LED8 Yellow Off Card is receiving SPACE signal from port 2 LED9 Yellow On Card is transmitting MARK signal to port 3 LED9 Yellow Off Card is transmitting SPACE signal to port 3 LED10 Yellow On Card is receiving MARK signal from port 3 LED10 Yellow Off Card is receiving SPACE signal from port 3 LED11 Yellow On Card is transmitting MARK signal to port 4 LED11 Yellow Off Card is transmitting SPACE signal to port 4 LED12 Yellow On Card is receiving MARK signal from port 4 LED12 Yellow Off Card is receiving SPACE signal from port 4 LED13 Yellow On Card is transmitting MARK signal to network LED13 Yellow Off Card is transmitting SPACE signal to network LED14 Yellow On Card is receiving MARK signal from network LED14 Yellow Off Card is receiving SPACE signal from network Card Type Serial I/O Options Serial port [Image] CONNECTIONS Function Label Function Label V.11 V.24, V.35, V.36, CN1 Header to main board CN2B or DSU port (on both front and back of card) USER CONFIGURABLE SETTINGS Setting Label Position » Pin 22 used for ring indicator P22 Pins 2 & 3 closed Pin 22 used to enter test mode P22 Pins 1 & 2 in DCE mode, ring indicator in closed DTE mode » Pin 25 used for test mode P25 Pins 1 & 2 indicator closed Pin 25 used for test mode P25 Pins 2 & 3 indicator for DCE mode, busy out closed for DTE mode SERIAL PORT TYPE Setting SW1/1 SW1/2 SW1/3 SW1/4 SW1/5 SW1/6 V.11 DTE Off Off Off Off Off On V.11 DCE Off Off Off Off Off On V.24 DTE On On On On On Off V.24 DCE On On On On On Off V.35 DTE Off Off Off Off Off On V.35 DCE Off Off Off Off Off On V.36 DTE Off Off Off Off Off On V.36 DCE Off Off Off Off Off On DSU Off Off Off Off Off On SERIAL PORT TYPE (CON’T) Setting SW1/7 SW1/8 U1 V.11 DTE On On V.11 module in position 1 V.11 DCE On On V.11 module in position 2 V.24 DTE Off Off V.24 module in position 1 V.24 DCE Off Off V.24 module in position 2 V.35 DTE On On V.35 module in position 1 V.35 DCE On On V.35 module in position 2 V.36 DTE On On V.36 module in position 1 V.36 DCE On On V.36 module in position 2 DSU On On DSU module in position 1 Card Type ISDN TA ISDN Transfer Rate 64Kbps x 2 ISDN Protocol Unidentified Switch Type Unidentified [Image] CONNECTIONS Function Label Function Label Line in/out CN1 Line in/out CN3 Header to main board CN2B (on both front and back of card) Note:Two connectors are provided so the user can daisy-chain devices on the S/T bus. USER CONFIGURABLE SETTINGS Setting Label Position » S/T bus not terminated SW1 Off S/T bus terminated SW1 On Card Type ISDN TA ISDN Transfer Rate 64Kbps x 2 ISDN Protocol Unidentified Switch Type Unidentified [Image] CONNECTIONS Function Label Function Label Line out CN1 Header to main board CN2B (on both front and back of card) VANGUARD 305 (DSU DAUGHTERCARD) Card Type DDS DSU DSU Transfer Rate 56Kbps Modulation Protocol Unidentified [Image] CONNECTIONS Function Label Function Label Line out CN1 Header to main board CN2B (on both front and back of card)