PURETEK INDUSTRIAL CO, INC. 14400BPS FAX/MODEM ADAPTER WITH VOICE Card Type Fax, Modem (asynchronous), Voice Chip Set Unidentified I/O Options Speakerphone, Voicemail Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus 8-bit ISA Fax Class Class II Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Line out CN1 Microphone connection CN3 Line in CN2 Speaker connection CN4 SERIAL PORT ADDRESS Setting J1 J2 J3 COM1 (3F8h) Open Open Open COM2 (2F8h) Closed Open Open COM3 (3E8h) Open Closed Open COM4 (2E8h) Closed Closed Open COM5 Open Open Closed COM6 Closed Open Closed COM7 Open Closed Closed COM8 Closed Closed Closed INTERRUPT SELECTION Setting J4 J5 J6 J7 J8 2 Closed Open Open Open Open 3 Open Closed Open Open Open 4 Open Open Closed Open Open 5 Open Open Open Closed Open 9 Open Open Open Open Closed SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, ‘Comma’, A/ A, B, D, E, H, L, M, O, Q, S, V, X, Y, Z &C, &D, &F, &G, &J, &K, &M, &P, &R, &S, &T, &V, &W, &X, &Y, &Z Extended AT Commands \A, \B, \E, \J, \K, \L, \O, \U, \V, \X, %A S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S25 S26, S27, S36, S46, S82, S95 Note: Please see MHI Help file for full command documentation. Proprietary AT Command Set BIT-MAPPED REGISTER S23 Format AT [cmds] S23=n [cmds] Default: 28 Range: 0-191 Unit: Bit-mapped Description: Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone. Bit Value Function 0 0 Remote digital loopback denied 1 Remote digital loopback allowed 3 - 1 000 Sets serial port speed to 0-300bps 001 Sets serial port speed to 600bps 010 Sets serial port speed to 1200bps 011 Sets serial port speed to 2400bps 100 Sets serial port speed to 4800bps 101 Sets serial port speed to 9600bps 110 Sets serial port speed to 19200bps 111 Sets serial port speed to 48400bps or upper data rate 5, 4 00 Parity even 01 Space Parity 10 Parity odd 11 Mark or No Parity 7, 6 00 Guard tone disabled 01 Guard tone 550Hz enabled 10 Guard tone 1800Hz enabled BIT SAMPLING Type: Configuration Format: AT [cmds] #VBS=n [cmds] Description: Select bit sampling Command Function #VBS? Returns current setting of #VBS command #VBS=2 2 bits per sample ADPCM enabled #VBS=3 3 bits per sample ADPCM enabled #VBS=4 4 bits per sample ADPCM enabled BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K0 Online command mode enabled, send no break to remote modem \K1 Break sent to remote modem and buffers cleared \K2 Online command mode enabled, send no break to remote modem \K3 Send break to remote modem immediately \K4 Online command mode enabled, send no break to remote modem \K5 Send break with transmitted data COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 Data compression enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP Reliable mode enabled \N3 MNP auto-reliable mode enabled \N4 V.42 reliable mode with phase detection enabled \N5 V.42 auto-reliable mode with phase detection enabled \N6 V.42 reliable mode without phase detection enabled \N7 V.42 auto-reliable mode without phase detection enabled DIAL - STORED NUMBER Type: Immediate Format: AT [cmds] DS=n [cmds] Description: Dial stored number from memory location n, (n=0-2) DIAL/BUSY TONE DETECT RANGE Type: Register Format: AT [cmds] S96=n [cmds] Description: Selects the range the modem uses for dial/busy tone detection Command Range Function S96=0 350 - 620Hz USA, Korea, Taiwan S96=1 425 - 450Hz Belgium S96=2 440 - 700Hz France S96=3 350 - 450Hz Israel, Japan S96=4 375 - 475Hz Italy, Norway, Germany, Denmark S96=5 150 - 450Hz Netherlands S96=6 270 - 320Hz Singapore S96=7 350 - 500Hz Sweden S96=8 375 - 550Hz Switzerland S96=9 350 - 440Hz United Kingdom S96=10 110 - 700Hz Full range ENERGY DETECTION THRESHOLD Type: Register Format: AT [cmds] S97=n [cmds] Default: 45 Range: Unidentified Unit: Unidentified Description: Selects dial tone detect threshold during CPM mode EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] Wn [cmds] Description: Controls extended result codes Command Function W0 V.42 extended result codes disabled W1 V.42 extended result codes enabled FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 XON/XOFF software flow control enabled \Q2 CTS hardware flow control enabled \Q3 RTS/CTS hardware flow control enabled INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0-90 Unit: 1 minute Description: Sets the length of time that the modem does not receive information before it disconnects. LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects line type Command Line Type &L0 Switched line &L1 Leased-line - 2-wire &L2 Leased-line - 4-wire MODE SELECTION Type: Configuration Format: AT [cmds] #CLS=n [cmds] Description: Controls the mode the modem will operate in Command Function #CLS? Returns current setting of #CLS command #CLS=0 Data mode enabled #CLS=2 Fax class 2 command mode enabled #CLS=8 Voice mode enabled MODEM MANUFACTURER Type: Immediate Format: AT [cmds] #MFR? [cmds] Description: Reports modem manufacturer MODEM MODEL Type: Immediate Format: AT [cmds] #MDL? [cmds] Description: Reports modem models MODEM REVISION Type: Immediate Format: AT [cmds] #REV? [cmds] Description: Reports modem revision REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product-identification code I1 Reports factory code I2 Reports internal memory test I3 Reports firmware version 1 I4 Reports firmware version 2 SIGNAL ROUTING Type: Configuration Format: AT [cmds] #VLS=n [cmds] Description: Select which signal is routed through the modem Command Function #VLS? Returns current setting of #VLS command #VLS=0 Phone line interface routed through the modem #VLS=1 Handset routed through the modem #VLS=2 External speaker routed through the modem #VLS=3 Auxiliary input device routed through the modem #VLS=4 Internal speaker routed through the modem SPEED - AUTOBAUD Type: Configuration Format: AT [cmds] #BDR=n [cmds] Description: Controls speed Command Function #BDR? Returns current setting of #BDR command #BDR=0 Autobaud detection enabled #BDR=n Returns ‘OK’ and switches to new speed specified by n*2400bps (n=1,2,4,6,8,16,24) TONE GENERATION Type: Configuration Format: AT [cmds] #VBT=n [cmds] Default: Unidentified Range: 1-40 Unit: .1 second Description: Controls the amount of time a tone is generated Command Function #VBT? Returns current setting of #VBT command VOICE COMPRESSION METHOD Type: Immediate Format: AT [cmds] #VCI? [cmds] Description: Reports voice compression method used VOICE INACTIVITY TIMER Type: Register Format AT [cmds] S30=n [cmds] Default: 0 Range: 0-255 Unit: 1 second Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process. Note: S30=0 disables the timer and allows indefinite inactivity. VOICE RECEIVE Type: Immediate Format: AT [cmds] #VTX [cmds] Description: Enables voice receive during voice command mode VOICE TRANSMIT Type: Immediate Format: AT [cmds] #VTX [cmds] Description: Enables voice transmission during voice command mode V.25bis COMMAND SET CALL REQUESTED NUMBER Type: Immediate Format: CRN<#> Description: Dials the number given; it will ignore spaces and hyphens in the string. CALL REQUEST WITH ADDRESS Type: Immediate Format: CRSn Description: Dials the number stored in NVRAM at location n PROGRAM NUMBER Type: Configuration Format: PRNn;<#> Description: Stores a phone number in NVRAM at location n REQUEST LISTED NUMBERS Type: Immediate Format: RLN Description: Requests the modem to return the list of stored numbers in NVRAM DISREGARD INCOMING CALL Type: Immediate Format: DIC Description: Instructs the modem to ignore the incoming call, if the modem is set to automatically answer. CONNECT INCOMING CALLS Type: Immediate Format: CID Description: Instructs the modem to answer an incoming call. V.25bis/AT COMMANDS Type: Immediate Format: AT [cmds] ATC [cmds] Description: Toggles between V.25bis and AT command set