CARDINAL TECHNOLOGIES, INC 9600BPS V.32 V.42BIS FAX (1/2CARD-VER.1) Card Type Modem (asynchronous) Chip Set Unidentified Maximum Data Rate 9600bps Maximum Fax Rate Unidentified Data Bus 8-bit ISA Fax Class Class I & II Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.32 Fax Modulation Protocol Unidentified Error Correction/Compression MNP5, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Line out/in CN1 Line in/out CN2 SERIAL PORT ADDRESS Setting SW1/1 SW1/2 COM1 (3F8h) Off Off COM2 (2F8h) Off On COM3 (3E8h) On Off COM4 (2E8h) On On INTERRUPT SELECTION Setting SW1/3 SW1/4 2 On On 3 Off On 4 Off Off 5 On Off SUPPORTED COMMAND SET Basic AT Commands AT, ‘Comma’, A/ A, B, C, E, F, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &U, &V, &W, &Y, &Z Extended AT Commands \A, \B, \C, \G, \J, \O, \U, \V, \X, \Y, \Z %A, %E, %G S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S25 S26, S27, S30, S37, S95, S108, S109, S110 Special Commands "H, "O, -C, -J, -V Note: Please see MHI Help file for full command documentation. Proprietary AT Command Set BIT-MAPPED REGISTER S23 Format AT [cmds] S23=n [cmds] Default: 15 Range: 0-191 Unit: Bit-mapped Description: Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone. Bit Value Function 0 0 Remote digital loopback denied 1 Remote digital loopback allowed 3 - 1 000 Sets serial port speed to 0-300bps 001 Sets serial port speed to 1200bps 010 Sets serial port speed to 2400bps 011 Sets serial port speed to 4800bps 100 Sets serial port speed to 7200bps 101 Sets serial port speed to 9600bps or 14400bps 110 Sets serial port speed to 19200bps 111 Sets serial port speed to 38400bps or 57600bps 5, 4 00 Parity even 01 Space or No parity 10 Parity odd 11 Mark Parity 7, 6 00 Guard tone disabled 01 Guard tone 550Hz enabled 10 Guard tone 1800Hz enabled BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Break from Modem Break from Break DTE in receives \B DTE in received RELIABLE or during DIRECT mode from remote NORMAL mode command modem state \K0 Online Break sent Online Buffers command mode to remote command mode cleared, enabled, modem and enabled, break sent send no buffers send break to DTE break to cleared to remote remote modem modem \K1 Break sent Break sent Send break Buffers to remote to remote to remote cleared, modem and modem and modem break sent buffers buffers immediately to DTE cleared cleared \K2 Online Send break Online Break sent command mode to remote command mode immediately enabled, modem enabled, to DTE send no immediately send break break to to remote remote modem modem \K3 Send break Send break Send break Break sent to remote to remote to remote immediately modem modem modem to DTE immediately immediately immediately \K4 Online Send break Online Break sent command mode with command mode with enabled, transmitted enabled, received send no data send break data to the break to to remote DTE remote modem modem \K5 Send break Send break Send break Break sent with with to remote with transmitted transmitted modem received data data immediately data to the DTE COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 MNP5 disabled %C1 MNP5 enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP reliable mode enabled \N3 V.42 auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 LAPM/Normal mode enabled DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Modifier Function P Pulse dialing enabled R Answer mode enabled, originate mode disabled following handshake initiation S=n Dial stored telephone number n=0-3 T Tone dialing enabled W Dialing resumed following dial tone detection , Dialing paused for amount of time specified in S8 register ! Modem commanded to go off-hook for specified time before returning on-hook @ Wait for quiet answer ; Modem returned to command state after dialing DTE CONNECT SPEED Type: Configuration Format: AT [cmds] S112=n [cmds] Description: Select the DTE speed during data transfer Command Function S112=0 Last AT speed S112=1 Not used S112=2 Sets DTE speed to 300bps S112=3 Sets DTE speed to 1200bps S112=4 Sets DTE speed to 2400bps S112=5 Sets DTE speed to 4800bps S112=6 Sets DTE speed to 7200bps S112=7 Sets DTE speed to 9600bps S112=8 Sets DTE speed to 12000bps S112=9 Sets DTE speed to 14400bps S112=10 Sets DTE speed to 16800bps S112=11 Sets DTE speed to 19200bps S112=12 Sets DTE speed to 38400bps S112=13 Sets DTE speed to 57600bps S112=14 Sets DTE speed to 600bps FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bi-directional XON/XOFF flow control enabled \Q2 Unidirectional hardware flow control enabled \Q3 Bi-directional hardware flow control enabled (RTS/CTS) INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0-90 Unit: 1 minute Description: Sets the length of time that the modem does not receive information before it disconnects. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports ROM checksum I2 Tests and reports ROM checksum I3 Reports ROM components I4 Reports modem capabilities