MOTOROLA, INC. HMTA 200 V.32BIS Card Type ISDN TA Chip Set Motorola ISDN Transfer Rate 64Kbps x 2 Maximum Modem Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Fax Class Unidentified Data Bus External ISDN Protocol V.120, PPP, AIMux, Bonding Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol Unidentified Switch Type 5ESS, DMS-100, NI-1 Error Correction/Compression MNP5, V.42bis Proprietary AT Command Set V2152 AUTO-RELIABLE BUFFER Type: Configuration Format: AT [cmds] \Cn [cmds] Description: Sets the behaviour of the buffer during auro-reliable negotiation. Command Function \C0 Auto-reliable buffer disabled. \C1 Modem will buffer data for four seconds or 200 bytes. \C2 Modem will fall back to normal mode if fallback character received. BEARER CALL - 3.1KHz AUDIO Type: Configuration Format: AT [cmds] %A94=x [cmds] Description: Selects how the TA will answer an incoming 3.1KHz audio BC call. Command Function %A94=D TA will not answer 3.1KHz audio BC calls. %A94=E TA will answer 3.1KHz audio BC calls as ISDN. %A94=M TA will answer 3.1KHz audio BC calls with the modem. BEARER CALL - DATA Type: Configuration Format: AT [cmds] %A95=x [cmds] Description: Selects how the TA will answer an incoming data BC call. Command Function %A93=D TA will not answer data BC calls. %A93=E TA will answer data BC calls as ISDN. %A93=M TA will answer data BC calls with the modem. BEARER CALL - SPEECH Type: Configuration Format: AT [cmds] %A93=x [cmds] Description: Selects how the TA will answer an incoming speech BC call. Command Function %A93=D TA will not answer speech BC calls. %A93=E TA will answer speech BC calls as ISDN. %A93=M TA will answer speech BC calls with the modem. BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal. Command Break from DTE Break from Modem Break from DTE receives \B remote modem Reliable/Normal mode Direct mode \K0 Enter command Send break to Buffers Buffers mode, do not remote modem cleared and cleared and send break to immediately, break sent to break sent to remote modem. then enter remote modem. DTE. command mode. \K1 Buffers cleared Send break to Buffers Buffers and break sent remote modem cleared and cleared and to remote immediately. break sent to break sent to modem. remote modem. DTE. \K2 Enter command Send break to Send break to Send break to mode, do not remote modem remote modem DTE send break to immediately, immediately. immediately. remote modem. then enter command mode. \K3 Send break to Send break to Send break to Send break to remote modem remote modem remote modem DTE immediately. immediately. immediately. immediately. \K4 Enter command Send break to Send break to Break sent mode, do not remote modem remote modem with received send break to immediately, with data to the remote modem. then enter transmitted DTE. command mode. data. \K5 Send break with Send break to Send break to Break sent transmitted remote modem remote modem with received data. immediately. with data to the transmitted DTE. data. CALLER ID Type: Configuration Format: AT [cmds] @N0=n [cmds] Description: Enables the Caller ID function. Command Function @N0=0 Caller ID disabled. @N0=1 Caller ID enabled. CALLER ID LOG Type: Immediate Format: AT [cmds] @Ln [cmds] Description: Allows the user to view and clear the Caller ID log. Command Function @L0 Clears the Caller ID log. @L1 View the last entry in the Caller ID log. @L2 View the last ten entries in the Caller ID log. CD SIGNAL Type: Configuration Format: AT [cmds] &Cn [cmds] Description: Controls the behaviour of the CD signal. Command Function &C0 CD forced high. &C1 CD normal. &C2 CD forced low on disconnect. COMMAND SET Type: Configuration Format: AT [cmds] @P1=x [cmds] Description: Selects the command set that will be used. Command Function @P1=A AT command set enabled. @P1=N Command sets disabled. @P1=VB V.25bis command set enabled in Bisync mode. @P1=VH V.25bis command set enabled in HDLC mode. COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects how the modem will compress data. Command Function %C0 Compression disabled. %C1 Compression enabled. %C2 Compression enabled on transmit only. %C3 Compression enabled on receive only. COMPRESSION/ERROR CORRECTION MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Selects the types of compression and error correction that will be attempted. Command Function \N0 Normal mode only, compression and error correction disabled. \N1 Direct mode only, compression and error correction disabled. \N2 MNP attempted, modem will disconnect if MNP connection fails. \N3 MNP attempted, modem will attempt normal mode if MNP connection fails. \N4 LAPM attempted, modem will disconnect if LAPM connection fails. \N5 LAPM attempted, modem will attempt normal mode if LAPM connection fails. \N6 LAPM attempted, then MNP, modem will disconnect if both previous connections fail. \N7 LAPM attempted, then MNP, modem will attempt normal mode if both previous connections fail. DATA LENGTH Type: Configuration Format: AT [cmds] @P4=n [cmds] Description: Selects the length of the data word. Command Function @P4=7 7 bit word length. @P4=8 8 bit word length. DATA PARITY Type: Configuration Format: AT [cmds] @P3=x [cmds] Description: Selects the format of the parity bit. Command Function @P3=E Even parity. @P3=M Mark parity. @P3=N No parity. @P3=O Odd parity. DATA STOP Type: Configuration Format: AT [cmds] @P6=n [cmds] Description: Selects the number of stop bits. Command Function @P6=0 One stop bit. @P6=1 One and a half stop bits. @P6=2 Two stop bits. DIAL MODE Type: Configuration Format: AT [cmds] %A97=x [cmds] Description: Selects what type of dialing the TA will use. Command Function %A97=E En bloc dialing enabled. %A97=O Overlap dialing enabled. DIRECTORY NUMBER 1 SET Type: Configuration Format: AT !N1=<#> AT [cmds] !N1="<#>" [cmds] Description: Sets the first directory number. The number must be surrounded by single or double quotes if there are more commands on the line. DIRECTORY NUMBER 2 SET Type: Configuration Format: AT !N2=<#> AT [cmds] !N2="<#>" [cmds] Description: Sets the first directory number. The number must be surrounded by single or double quotes if there are more commands on the line. DISCONNECT BUFFER TIME Type: Configuration Format: AT [cmds] %Dn [cmds] Default: 0 Range: 0 - 255 Unit: 1 second Description: Sets the time that the modem will wait to disconnect if there is data in its buffers. DISPLAY CONFIGURATION Type: Immediate Format: AT [cmds] >V=x [cmds] Description: Displays information about the current configuration. Command Function >V=C Displays directory numbers, SPIDs, and TEIs. >V=G Displays complete configuration. DISPLAY CONFIGURATION Type: Immediate Format: AT [cmds] &V=x[n] [cmds] Description: Displays information about the current configuration. Command Function &V Displays current and stored profiles. &V=Bn Displays X.25 session n. &V=E Displays V.120 CSD information. &V=Ln Displays local X.25 session n. &V=Rn Displays remote X.25 session n. &V=Z Displays stored phone numbers. DISPLAY FIRMWARE VERSION Type: Immediate Format: AT [cmds] %Vn [cmds] Description: Displays the version of the installed firmware. DISPLAY PRODUCT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information about the TA. Command Function I0 Displays product identification. I1 Displays ROM checksum. I2 Displays ROM checksum response. I3 Displays firmware version. I4 Displays modem capability in numeric form. I8 Displays modem capability in verbose form. I9 Displays Plug-And-Play ID. I10 Displays ISDN link status. DTR AUTODIAL Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Causes the TA to repeatedly dial the first stored number on high DTR until it connects. Command Function &L0 DTR autodialing disabled. &L1 DTR autodialing enabled. DTR CHANGE TIME Type: Register Format: AT [cmds] S25=n [cmds] Default: 5 Range: 0 - 255 Unit: 10ms Description: Sets the amount of time the DTR signal must be low before it is recognised. DTR SIGNAL Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Controls the behaviour of the DTR signal. Command Function &D0 DTR forced high. &D1 TA enters command mode when DTR goes low. &D2 TA hangs up and returns to command mode on low DTR. &D3 TA resets on low DTR. &D9 TA dials first stored number on high DTR, hangs up and returns to command mode on low DTR. ECHO CANCELLER DISABLE Type: Configuration Format: AT [cmds] %A96=n [cmds] Description: Selects whether the TA will send a tone to disable the echo canceller. Command Function %A96=0 TA will not send echo canceller disable tone. %A96=1 TA will send echo canceller disable tone. EXTENDED RESULT CODES - MODEM Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects which speed the modem will display for connect messages. Command Function \V0 Display serial port speed only. \V1 Display serial port speed and error correction protocol. \V2 Display line speed only. \V3 Display line speed and error correction protocol. EXTENDED RESULT CODES - ISDN Type: Configuration Format: AT [cmds] Wn [cmds] Description: Selects whether the TA will send extended protocol and channel result codes. Command Function W0 Extended result codes disabled. W1 Extended result codes enabled. FLOW CONTROL - MODEM-TO-MODEM Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects whether the local and remote modems may use flow control. Command Function \G0 Modem-to-modem XON/XOFF flow control disabled. \G1 Modem-to-modem XON/XOFF flow control enabled. FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Selects the type of flow control that will be used. Command Function \Q0 Flow control disabled. \Q1 Bidirectional XON/XOFF flow control enabled. \Q2 CTS flow control enabled. \Q3 RTS/CTS flow control enabled. \Q4 Unidirectional XON/XOFF flow control enabled. Note: Unidirectional XON/XOFF is valid for ISDN operation only. If this mode is used while operating the modem it will not function properly. FRONT PANEL LOCK Type: Configuration Format: AT [cmds] >Ln [cmds] Description: Prevents front panel configuration changes. Command Function >L0 All actions allowed from front panel. >L1 Configuration changes from front panel not allowed. >L2 No actions allowed from front panel. INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0 - 90 Unit: 1 minute Description: Sets the amount of time that the modem must be idle before it will disconnect. LINE SPEED - MAXIMUM Type: Configuration Format: AT [cmds] %Bn [cmds] Description: Sets the maximum speed the modem will connect at. Command Function %B0 Modem will connect only at DCE speed. %B300 Modem will connect only at 300bps. %B1200 1200bps maximum connect speed. %B2400 2400bps maximum connect speed. %B4800 4800bps maximum connect speed. %B7200 7200bps maximum connect speed. %B9600 9600bps maximum connect speed. %B9600C 9600bps maximum connect speed with trellis coding. %B12000 12Kbps maximum connect speed. %B14400 14.4Kbps maximum connect speed. LOAD STORED PROFILE Type: Immediate Format: AT [cmds] Zn [cmds] Description: Loads the configuration of the TA from the stored profile except for ISDN settings. LOAD STORED PROFILE - FULL Type: Immediate Format: AT [cmds] >Zn [cmds] Description: Loads the complete configuration of the TA from the stored profile. LOCAL SERIAL PORT SPEED Type: Configuration Format: AT [cmds] @P2=n [cmds] Description: Sets the speed of operation for the serial port. Command Function @P2=300 Set serial port speed to 300bps. @P2=600 Set serial port speed to 600bps. @P2=1200 Set serial port speed to 1200bps. @P2=2400 Set serial port speed to 2400bps. @P2=4800 Set serial port speed to 4800bps. @P2=7200 Set serial port speed to 7200bps. @P2=9600 Set serial port speed to 9600bps. @P2=12000 Set serial port speed to 12Kbps. @P2=14400 Set serial port speed to 14.4Kbps. @P2=19200 Set serial port speed to 19.2Kbps. @P2=28800 Set serial port speed to 28.8Kbps. @P2=38400 Set serial port speed to 38.4Kbps. @P2=48000 Set serial port speed to 48Kbps. @P2=56000 Set serial port speed to 56Kbps. @P2=57600 Set serial port speed to 57.6Kbps. @P2=64000 Set serial port speed to 64Kbps. @P2=112000 Set serial port speed to 112Kbps. @P2=115200 Set serial port speed to 115.2Kbps. @P2=128000 Set serial port speed to 128Kbps. LOCK SERIAL PORT SPEED Type: Configuration Format: AT [cmds] \Jn [cmds] Description: Selects whether the serial port speed will be matched to the line speed. Command Function \J0 Serial port speed locked. \J1 Serial port speed will match line speed. MNP BLOCK SIZE Type: Configuration Format: AT [cmds] \An [cmds] Description: Sets the maximum size of a block in MNP mode. Command Function \A0 Maximum block size is 64 bytes. \A1 Maximum block size is 128 bytes. \A2 Maximum block size is 192 bytes. \A3 Maximum block size is 256 bytes. ORIGINATE CALL - ISDN Type: Configuration Format: AT [cmds] %A98=Ix [cmds] Description: Selects what bearer capability the TA will originate ISDN calls with. Command Function %A98=I Originate ISDN calls as data BC. %A98=IA Originate ISDN calls as 3.1KHz audio BC. %A98=ID Originate ISDN calls as data BC. %A98=IS Originate ISDN calls as speech BC. ORIGINATE CALL - MODEM Type: Configuration Format: AT [cmds] %A98=Mx [cmds] Description: Selects what bearer capability the TA will originate modem calls with. Command Function %A98=M Originate modem calls as 3.1KHz audio BC. %A98=MA Originate modem calls as 3.1KHz audio BC. %A98=MD Originate modem calls as data BC. %A98=MS Originate modem calls as speech BC. PROTOCOL Type: Configuration Format: AT [cmds] %A2=n [cmds] Description: Sets the protocol that the TA uses for rate adaptation. Command Function %A2=0 TA will use clear channel mode. %A2=2 TA will use V.120 protocol. %A2=3 TA will use Bonding Mode 1 or AIMux protocols. %A2=95 TA will use PPP protocol. RESET TO FACTORY DEFAULTS Type: Immediate Format: AT [cmds] &F [cmds] Description: Resets the configuration of the TA except for ISDN settings to the factory defaults. RESET TO FACTORY DEFAULT - FULL Type: Immediate Format: AT [cmds] >F [cmds] Description: Resets the complete configuration of the TA to the factory defaults. RETRAIN Type: Immediate Format: AT [cmds] On Description: When connected, tells the modem to go back online and initiate a retrain. Command Function O0 Return online without retrain. O1 Return online with retrain. O4800 Return online and negotiate to 4800bps. O7200 Return online and negotiate to 7200bps. O9600 Return online and negotiate to 9600bps. O12000 Return online and negotiate to 12Kbps. O14400 Return online and negotiate to 14.4Kbps. SPID 1 SET Type: Configuration Format: AT !C6=<#> AT [cmds] !C6="<#>" [cmds] Description: Sets the first SPID. The SPID must be surrounded by single or double quotes if there are more commands on the line. SPID 2 SET Type: Configuration Format: AT !C7=<#> AT [cmds] !C7="<#>" [cmds] Description: Sets the second SPID. The SPID must be surrounded by single or double quotes if there are more commands on the line. SWITCH TYPE Type: Configuration Format: AT [cmds] !C0=n [cmds] Description: Selects what type of network switch the TA is connected to. Command Function !C0=0 TA is connected to 5ESS switch. !C0=1 TA is connected to DMS-100 switch. !C0=2 TA is connected to NI-1 switch. SWITCH VERSION Type: Configuration Format: AT [cmds] !C1=n [cmds] Description: Selects what version of network switch the TA is connected to. Command Function !C1=0 TA is connected to point-to-point 5ESS switch. !C1=1 TA is connected to multipoint 5ESS switch. !C1=2 TA is connected to IC-0 DMS-100 switch. !C1=3 TA is connected to IC-1 DMS-100 switch. !C1=4 TA is connected to NI-1 switch. SYNC/ASYNC MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects whether the DTE will be operation in synchronous or asynchronous mode. Command Function &M0 DTE in asynchronous mode. &M1 DTE in asynchronous mode for dialing, synchronous mode for communications. &M2 DTE in synchronous mode, TA dials stored number on high DTR. TEI 1 SET Type: Configuration Format: AT [cmds] !D3=n [cmds] Description: Sets the first Terminal Endpoint Identifier. Command Function !D3=0 Sets the TEI to the value indicated. ... !D3=63 !D3=127 Disables channel 1. !D3=255 Allows dynamic TEI assignment. TEI 2 SET Type: Configuration Format: AT [cmds] !D4=n [cmds] Description: Sets the second Terminal Endpoint Identifier. Command Function !D4=0 Sets the TEI to the value indicated. ... !D4=63 !D4=127 Disables channel 2. !D4=255 Allows dynamic TEI assignment. TEI X.25 SET Type: Configuration Format: AT [cmds] !D0=n [cmds] Description: Sets the Terminal Endpoint Identifier for X.25. Command Function !D0=0 Sets the TEI to the value indicated. ... !D0=63 !D0=127 Disables X.25 operation. TRANSMISSION SPEED Type: Configuration Format: AT [cmds] %A4=n [cmds] Description: Sets the transmission speed of the TA. Command Function %A4=0 Transmission speed is 64Kbps. %A4=1 Transmission speed is 56Kbps. TRELLIS CODING Type: Configuration Format: AT [cmds] Bn [cmds] Description: Selects whether trellis coding will be used at 9600bps. Command Function B2 Trellis coding enabled. B3 Trellis coding disabled. V.120 RECEIVE FRAME SIZE Type: Configuration Format: AT [cmds] %E1=n [cmds] Default: 256 Range: 1 - 260 Unit: 1 byte Description: Sets the maximum size of a received V.120 frame. V.120 TRANSMIT FRAME SIZE Type: Configuration Format: AT [cmds] %E0=n [cmds] Default: 256 Range: 1 - 260 Unit: 1 byte Description: Sets the maximum size of a transmitted V.120 frame. V.120 TRANSMIT TIMER Type: Configuration Format: AT [cmds] %E3=n [cmds] Default: 10 Range: 1 - 255 Unit: Unidentified Description: Sets the V.120 T200 transmission timer. V.120 WINDOW SIZE Type: Configuration Format: AT [cmds] %E2=n [cmds] Default: 8 Range: 1 - 127 Unit: N/A Description: Sets the size of the V.120 window. V.42 FAST DETECT Type: Configuration Format: AT [cmds] \Mn [cmds] Description: Selects the normal or fast negotiation sequence for V.42. Command Function \M0 V.42 fast detect disabled. \M1 V.42 fast detect enabled. WRITE PROTECT Type: Configuration Format: AT [cmds] @G=x [cmds] Description: Selects the ability to prevent permanent changes to the TA’s configuration from being made. All changes made in temporary memory will be reset at the end of every call. Command Function @G=D Write protect disabled. @G=E Write protect enabled. WRITE TO STORED PROFILE Type: Immediate Format: AT [cmds] &Wn [cmds] Description: Saves the configuration of the TA except for ISDN settings to stored profile n. WRITE TO STORED PROFILE - FULL Type: Immediate Format: AT [cmds] >Wn [cmds] Description: Saves the complete configuration of the TA to stored profile n. X.25 AUTO-ANSWER Type: Configuration Format: AT [cmds] %B97=x [cmds] Description: Sets whether the TA will auto-answer an incoming X.25 virtual call. Command Function %B97=D Auto-answer disabled. %B97=E Auto-answer enabled. X.25 CALL CHARGING Type: Configuration Format: AT [cmds] %B10=n [cmds] Description: Sets the type of call charging for X.25. Command Function %B10=0 X.25 will use normal call charging. %B10=1 X.25 will use reverse call charging. X.25 CLOSED USER GROUP Type: Configuration Format: AT [cmds] %B8=n [cmds] Description: Selects the type of Closed User Group used for X.25. Command Function %B8=0 CUG not used. %B8=1 Basic CUG used. %B8=2 CUG with outgoing access only used. %B8=3 CUG will full access used. X.25 CLOSED USER GROUP ID Type: Configuration Format: AT [cmds] %B9=nnnn [cmds] Description: Sets the ID for the X.25 CUG. X.25 CODE - INCOMING Type: Read-only Format: AT [cmds] %B16? [cmds] Description: Stores the result code for incoming X.25 virtual calls. Value Meaning 0 Call was not redirected. 1 Station was busy. 9 Station was out of order. 15 Call was redirected. X.25 CODE - OUTGOING Type: Immediate Format: AT [cmds] %B15? [cmds] Description: Stores the result code for outgoing X.25 virtual calls. Value Meaning 0 Call was not redirected. 1 Station was busy. 7 Call was within a hunt group. 9 Station was out of order. 15 Call was redirected. X.25 D-CHANNEL Type: Configuration Format: AT [cmds] !C3=n [cmds] Description: Selects whether X.25 will be used on the D-channel. Command Function !C3=0 X.25 disabled on D-channel. !C3=1 X.25 enabled on D-channel. X.25 D-CHANNEL - CHANNELS, BIDIRECTIONAL Type: Configuration Format: AT [cmds] !X6=n [cmds] Default: 8 Range: 0 - 255 Unit: N/A Description: Sets the number of bidirectional logical channels for X.25. X.25 D-CHANNEL - CHANNELS, INCOMING Type: Configuration Format: AT [cmds] !X5=n [cmds] Default: 0 Range: 0 - 255 Unit: N/A Description: Sets the number of incoming logical channels for X.25. X.25 D-CHANNEL - CHANNELS, OUTGOING Type: Configuration Format: AT [cmds] !X7=n [cmds] Default: 0 Range: 0 - 255 Unit: N/A Description: Sets the number of outgoiing logical channels for X.25. X.25 D-CHANNEL - CHANNELS, VIRTUAL Type: Configuration Format: AT [cmds] !X4=n [cmds] Default: 0 Range: 0 - 255 Unit: N/A Description: Sets the number of permanent virtual channels for X.25. X.25 D-CHANNEL - MODULUS Type: Configuration Format: AT [cmds] !X8=n [cmds] Default: 8 Range: 8, 128 Unit: N/A Description: Sets the sequence modulus for X.25. X.25 D-CHANNEL - NEGOTIATION Type: Configuration Format: AT [cmds] !D1=n [cmds] Description: Selects X.25 parameter negotiation. Command Function !D1=0 X.25 negotiation disabled. !D1=1 X.25 negotiation enabled. X.25 D-CHANNEL - RECEIVE PACKET SIZE Type: Configuration Format: AT [cmds] !X2=n [cmds] Description: Sets the size of the received packets for X.25. Command Function !X2=7 Packet size set to 128 bytes. !X2=8 Packet size set to 256 bytes. X.25 D-CHANNEL - RECEIVE WINDOW SIZE Type: Configuration Format: AT [cmds] !X0=n [cmds] Default: 2 Range: 1 - 7 Unit: N/A Description: Sets the size of the X.25 receive window. X.25 D-CHANNEL - TRANSMIT PACKET SIZE Type: Configuration Format: AT [cmds] !X3=n [cmds] Description: Sets the size of the transmitted packets for X.25. Command Function !X3=7 Packet size set to 128 bytes. !X3=8 Packet size set to 256 bytes. X.25 D-CHANNEL - TRANSMIT WINDOW SIZE Type: Configuration Format: AT [cmds] !X1=n [cmds] Default: 2 Range: 1 - 7 Unit: N/A Description: Sets the size of the X.25 transmit window. X.25 LOGICAL CHANNEL Type: Configuration Format: AT [cmds] %B6=n [cmds] Default: 1 Range: 0 - 255 Unit: N/A Description: Selects the logical channel for X.25 operation. X.25 OUTGOING CALL ADDRESS Type: Configuration Format: AT [cmds] %B17=nnnn [cmds] Description: Sets the address for an outgoing X.25 virtual call. X.25 PACKET CALL TIMER Type: Configuration Format: AT [cmds] %B98=n [cmds] Default: 200 Range: 0 - 600 Unit: Unidentified Description: Sets the packet call timer for X.25 operation. X.25 PAD ANCILLARY DEVICE Type: Configuration Format: AT [cmds] %L5=n [cmds] Description: Selects control of an ancillary device by the PAD. Command Function %L5=0 Device disabled. %L5=1 Device enabled for data transfer only. %L5=2 Device enabled for data transfer and command control. X.25 PAD BREAK RESPONSE Type: Configuration Format: AT [cmds] %L7=n [cmds] Default: 0 Range: 0 - 31 Description: Sets action the PAD takes in response to receiving a BREAK from the DTE. Bit Value Function 0 0 PAD will not send an interrupt packet. 1 PAD will send an interrupt packet. 1 0 PAD will not send a reset packet. 1 PAD will send a reset packet. 2 0 PAD will not send an indication of the break. 1 PAD will send an indication of the break. 3 0 PAD will not escape from the data state. 1 PAD will escape from the data state. 4 0 PAD will not set %L8 to 1. 1 PAD will set %L8 to 1. X.25 PAD CARRIAGE RETURN TRANSLATION Type: Configuration Format: AT [cmds] %L13=n [cmds] Default: 5 Range: 0 - 7 Description: Selects when the PAD will add line feeds to carriage returns. Bit Value Function 0 0 PAD will not add a line feed after a carriage return being sent to the DTE. 1 PAD will add a line feed after a carriage return being sent to the DTE. 1 0 PAD will not add a line feed after a carriage return being received from the DTE. 1 PAD will add a line feed after a carriage return being received from the DTE. 2 0 PAD will not add a line feed after a carriage return being echoed. 1 PAD will add a line feed after a carriage return being echoed. X.25 PAD - CARRIAGE RETURN PADDING Type: Configuration Format: AT [cmds] %L9=n [cmds] Default: 0 Range: 0 - 255 Unit: Unidentified Description: Sets the amount of padding after a carriage return. X.25 PAD DATA EDITING Type: Configuration Format: AT [cmds] %L15=n [cmds] Description: Selects whether editing the data being transferred is allowed. Command Function %L12=0 Editing disabled. %L12=1 Editing enabled. X.25 PAD DELETE CHARACTER Type: Configuration Format: AT [cmds] %L16=n [cmds] Default: 8 Range: 0 - 127 Unit: 1 ASCII character Description: Sets the character used for character deletion. X.25 PAD - DISCARD DATA Type: Configuration Format: AT [cmds] %L8=n [cmds] Description: Selects whether the PAD will deliver data to the DTE. Command Function %L8=0 Deliver data to the DTE. %L8=1 Discard data. X.25 PAD ECHO Type: Configuration Format: AT [cmds] %L2=n [cmds] Description: Selects whether PAD functions will echo incoming characters. Command Function %L2=0 PAD echo disabled. %L2=1 PAD echo enabled. X.25 PAD ECHO MASK Type: Configuration Format: AT [cmds] %L20=n [cmds] Default: 248 Range: 0 - 255 Description: Selects which control characters will be echoed. Bit Value Function 0 0 Carriage return will be echoed. 1 Carriage return will not be echoed. 1 0 Line feed will be echoed. 1 Line feed will not be echoed. 2 0 The control characters VT, HT, and form feeds will be echoed. 1 The control characters VT, HT, and form feeds will not be echoed. 3 0 Bells and backspaces will be echoed. 1 Bells and backspaces will not be echoed. 4 0 The control character ENQ and escapes will be echoed. 1 The control character ENQ and escapes will not be echoed. 5 0 The control characters ACK, NAK, STX, SOH, EOT, ETB, and ETX will be echoed. 1 The control characters ACK, NAK, STX, SOH, EOT, ETB, and ETX will not be echoed. 6 0 Parameters 16, 17, and 18 will be echoed. 1 Parameters 16, 17, and 18 will not be echoed. 7 0 All other control characters will be echoed. 1 All other control characters will not be echoed. X.25 PAD FLOW CONTROL Type: Configuration Format: AT [cmds] %L12=n [cmds] Description: Selects flow control for the X.25 PAD. Command Function %L12=0 Flow control disabled. %L12=1 Flow control enabled. X.25 PAD - FORM FEED PADDING Type: Configuration Format: AT [cmds] %L22=n [cmds] Default: 0 Range: 0 - 255 Unit: Unidentified Description: Sets the amount of padding after a form feed. X.25 PAD FORWARDING Type: Configuration Format: AT [cmds] %L3=n [cmds] Default: 2 Range: 0 - 127 Description: Selects which characters will be forwarded through the PAD. Bit Value Function 0 0 Alphanumeric characters will not be forwarded. 1 Alphanumeric characters (A-Z, a-z, 0-9) will be forwarded. 1 0 Carriage returns will not be forwarded. 1 Carriage returns will be forwarded. 2 0 The control characters ENQ, ACK, bells, and escapes will not be forwarded. 1 The control characters ENQ, ACK, bells, and escapes will be forwarded. 3 0 The control characters CAN, DC2, and delete will not be forwarded. 1 The control characters CAN, DC2, and delete will be forwarded. 4 0 The control characters ETX and EOT will not be forwarded. 1 The control characters ETX and EOT will be forwarded. 5 0 The control characters HT, LT, VT, and form feeds will not be forwarded. 1 The control characters HT, LT, VT, and FF will be forwarded. 6 0 All other control characters will not be forwarded. 1 All other control characters will be forwarded. X.25 PAD IDLE TIME Type: Configuration Format: AT [cmds] %L4=n [cmds] Default: 0 Range: 0 - 255 Unit: Unidentified Description: Sets the PAD’s idle time delay. X.25 PAD LINE DELETE CHARACTER Type: Configuration Format: AT [cmds] %L17=n [cmds] Default: 24 Range: 0 - 127 Unit: 1 ASCII character Description: Sets the character used for line deletion. X.25 PAD LINE DISPLAY CHARACTER Type: Configuration Format: AT [cmds] %L18=n [cmds] Default: 18 Range: 0 - 127 Unit: 1 ASCII character Description: Sets the character used for line display. X.25 PAD - LINE FEED PADDING Type: Configuration Format: AT [cmds] %L14=n [cmds] Default: 0 Range: 0 - 255 Unit: Unidentified Description: Sets the amount of padding after a line feed. X.25 PAD - LINE WRAP Type: Configuration Format: AT [cmds] %L10=n [cmds] Default: 0 Range: 0 - 255 Unit: 1 character Description: Sets the length of a line for the X.25 PAD. X.25 PAD - LOCAL SERIAL PORT SPEED Type: Configuration Format: AT [cmds] %L11=n [cmds] Description: Sets the speed of operation for the serial port when using the X.25 PAD. Command Function %L11=2 Set serial port speed to 300bps. %L11=3 Set serial port speed to 1200bps. %L11=4 Set serial port speed to 600bps. %L11=12 Set serial port speed to 2400bps. %L11=13 Set serial port speed to 4800bps. %L11=14 Set serial port speed to 9600bps. %L11=15 Set serial port speed to 19.2Kbps. %L11=16 Set serial port speed to 38.4Kbps. X.25 PAD PARITY Type: Configuration Format: AT [cmds] %L21=n [cmds] Description: Selects the format of the parity bit. Command Function %L21=0 No parity. %L21=3 Use setting in @P3. X.25 PAD RECALL Type: Configuration Format: AT [cmds] %L1=n [cmds] Default: 0 Range: 0, 1, 32 - 126 Unit: 1 ASCII character (see below for exceptions) Description: Sets the character for PAD recall. 0 disables recall, and 1 sets it to the DLE control character. X.25 PAD SERVICE SIGNALS Type: Configuration Format: AT [cmds] %L6=n [cmds] Description: Selects which PAD service signals will be sent to the user. Command Function %L6=0 No signals will be sent. %L6=1 All signals except prompt will be sent. %L6=4 Only prompt will be sent. %L6=5 All signals will be sent. X.25 PAD SERVICE SIGNAL DESTINATION Type: Configuration Format: AT [cmds] %L19=n [cmds] Description: Selects where PAD service signals will be sent. Command Function %L19=0 Signals will not be sent. %L19=1 Signals will be sent to the printer. %L19=2 Signals will be sent to the monitor. X.25 PVC Type: Configuration Format: AT [cmds] %B5=n [cmds] Description: Selects whether X.25 will use Permanent Virtual Channel. Command Function %B5=0 X.25 PVC disabled. %B5=1 X.25 PVC enabled. X.25 RECEIVE PACKET SIZE Type: Configuration Format: AT [cmds] %B2=n [cmds] Default: 0 Range: 0, 7 - 10 Unit: N/A Description: Sets the size of the received packets for X.25. X.25 RECEIVE THROUGHPUT Type: Configuration Format: AT [cmds] %B11=n [cmds] Description: Sets the throughput for receiving X.25. Command Function %B11=0 Use network speed. %B11=3 Throughput set to 75bps. %B11=4 Throughput set to 110bps. %B11=5 Throughput set to 300bps. %B11=6 Throughput set to 600bps. %B11=7 Throughput set to 1200bps. %B11=8 Throughput set to 2400bps. %B11=9 Throughput set to 4800bps. %B11=10 Throughput set to 9600bps. %B11=11 Throughput set to 19.2Kbps. %B11=12 Throughput set to 48Kbps. %B11=13 Throughput set to 64Kbps. X.25 RECEIVE WINDOW SIZE Type: Configuration Format: AT [cmds] %B0=n [cmds] Default: 0 Range: 0 - 8 Unit: N/A Description: Sets the size of the X.25 receive window. X.25 RESET CODE Type: Read-only Format: AT [cmds] %B20? [cmds] Description: Reports the reason for an X.25 reset. Value Meaning 0 Normal operation - no reset has occurred. 1 DTE caused reset. 2 Local procedure error occurred. 3 Destination address is incompatible. 4 Network is busy. 5 Remote procedure error occurred. 6 Cause of reset unknown. X.25 RESET TIMER Type: Configuration Format: AT [cmds] %B99=n [cmds] Default: 180 Range: 0 - 600 Unit: Unidentified Description: Sets the reset timer for X.25 operation. X.25 RPOA Type: Configuration Format: AT [cmds] %B14=xxxx [cmds] Description: Sets the RPOA for X.25. X.25 TRANSMIT DELAY TIME Type: Configuration Format: AT [cmds] %B19=n [cmds] Default: 0 Range: 0 - 65535 Unit: 1ms Description: Sets the delay time for X.25 transmission. X.25 TRANSMIT PACKET SIZE Type: Configuration Format: AT [cmds] %B3=n [cmds] Default: 0 Range: 0, 7 - 10 Unit: N/A Description: Sets the size of the transmitted packets for X.25. X.25 TRANSMIT THROUGHPUT Type: Configuration Format: AT [cmds] %B12=n [cmds] Description: Sets the throughput for transmitting X.25. Command Function %B12=0 Use network speed. %B12=3 Throughput set to 75bps. %B12=4 Throughput set to 110bps. %B12=5 Throughput set to 300bps. %B12=6 Throughput set to 600bps. %B12=7 Throughput set to 1200bps. %B12=8 Throughput set to 2400bps. %B12=9 Throughput set to 4800bps. %B12=10 Throughput set to 9600bps. %B12=11 Throughput set to 19.2Kbps. %B12=12 Throughput set to 48Kbps. %B12=13 Throughput set to 64Kbps. X.25 TRANSMIT WINDOW SIZE Type: Configuration Format: AT [cmds] %B1=n [cmds] Default: 0 Range: 0 - 8 Unit: N/A Description: Sets the size of the X.25 transmit window. X.25 USER DATA Type: Configuration Format: AT [cmds] %B18=xxxx [cmds] Description: Sets miscellaneous user data for X.25. X.25 USER ID Type: Configuration Format: AT [cmds] %B13=xxxx [cmds] Description: Sets the network user ID for X.25. XON/XOFF PASS THROUGH Type: Configuration Format: AT [cmds] \Xn [cmds] Description: Selects whether XON and XOFF characters will be sent to the remote modem. Command Function \X0 XON/XOFF characters trapped. \X1 XON/XOFF characters sent to remote modem.