SIIG, INC. DASH 14.4I FAX/MODEM INTERNAL Card Type Fax, Modem (asynchronous) Chip Set Unidentified Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus 8-bit ISA Fax Class Class I Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Phone line out CN1 Phone line in CN2 SERIAL PORT ADDRESS Setting JP1/D JP1/E JP1/F JP1/G COM1 (3F8h) Closed Open Closed Open COM2 (2F8h) Open Closed Closed Open COM3 (3E8h) Closed Open Open Closed COM4 (2E8h) Open Closed Open Closed INTERRUPT SELECTION Setting JP1/A JP1/B JP1/C 3 Closed Open Open 4 Open Closed Open 5 Open Open Closed Proprietary AT Command Set AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled %E2 Auto-fallback/fall-forward enabled BIT MAPPED REGISTERS Register Default S14 138 S16 0 S21 0 S22 117 S23 55 S27 73 S28 0 S31 2 S40 105 S41 3 BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Function \K0 Online command mode enabled, send no break to remote modem \K1 Break sent to remote modem and buffers cleared \K2 Online command mode enabled, send no break to remote modem \K3 Send break to remote modem immediately \K4 Online command mode enabled, send no break to remote modem \K5 Send break with transmitted data CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Modifier Function L Re-dial last number P Pulse dialing enabled R Accepted but not acted upon S=n Dial stored telephone number n (n=0-3) T Tone dialing enabled W Dialing resumed following dial tone detection ! Modem commanded to go off-hook for specified time before returning on-hook. @ Wait 5 seconds for quiet answer & Waits for prompt tone , Dialing paused for amount of time specified in S8 register ; Modem returned to command state after dialing ^ Toggles Calling tone enabled/disabled, for current call FLASH DIAL MODIFIER TIME Type: Register Format AT [cmds] S29=n [cmds] Default: 0 Range: 0-255 Unit: .01 second Description: Time the modem will go on-hook upon receiving the ! dial modifier in dial string. FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control Command Function \G0 Flow control disabled \G1 Flow control enabled FLOW CONTROL Type: Register Format AT [cmds] S39? [cmds] Description: Displays the current flow control Value Meaning 0 Flow control disabled 3 RTS/CTS flow control enabled 4 XON/XOFF flow control enabled 5 Transparent XON/XOFF flow control enabled 6 Both RTS/CTS and XON/XOFF flow control enabled FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S33=n [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S32=n [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON INACTIVITY TIMER Type: Register Format AT [cmds] S30=n [cmds] Default: 0 Range: 0-255 Unit: 10 seconds Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process. S30=0 will disable timer. LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %L [cmds] Description: Returns a value which indicates the received line signal level LINE SIGNAL QUALITY Type: Immediate Format: AT [cmds] %Q [cmds] Description: Returns a value which indicates line signal quality REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports precomputed checksum I2 Reports ‘OK’ I3 Reports firmware revision I4 Reports OEM defined identifier string I5 Reports country code I6 Reports data pump model and internal code revision RPI/DTE SPEED Type: Configuration Format: AT [cmds] +Hn [cmds] Description: Controls Rockwell Protocol Interface processing and DTE speed Command Function +H0 RPI disabled +H1 RPI enabled and set DTE speed to 19.2Kbps +H2 RPI enabled and set DTE speed to 38.4Kbps +H3 RPI enabled and set DTE speed to 57.6Kbps SLEEP TIMER Type: Register Format AT [cmds] S24=n [cmds] Default: 0 Range: 0-255 Unit: 1 second Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. S24=0 will disable timer. TRANSMISSION LEVEL - FAX Type: Register Format: AT [cmds] S92=n [cmds] Default: 10 Range: 0-15 Unit: -1 dBm Description: Sets the signal level for transmission while in fax mode TRANSMISSION LEVEL - PSTN Type Register or Configuration Format AT [cmds] S91=n [cmds] Default 10 Range 10-15 Unit -1 dBm Description Sets the signal level for transmission over switched phone lines