STOLLMANN GMBH TA-DD Card Type ISDN TA Chip Set Unidentified Maximum Data Rate 64Kbps x 2 Data Bus External ISDN Modulation Protocol V.110, 1TR6, DSS1, X.30 [Image] CONNECTIONS Function Label Function Label Line out CN1 V.24 or X.21 port 1 CN4 DC power CN2 Reset button SW1 V.24 or X.21 port 2 CN3 Note: X.21 functionality is provided by an included adapter cable. USER CONFIGURABLE SETTINGS Setting Label Position Editor debug mode disabled J3 Open Editor debug mode enabled J3 Closed TA will use saved profile J4 Open TA will use default profile only J4 Closed Remote configuration enabled J6 Open Remote configuration disabled J6 Closed Port 1 is in V.24 mode J9 Open Port 1 is in X.21 mode J9 Closed Port 2 is in V.24 mode J10 Open Port 2 is in X.21 mode J10 Closed Port 1 is in DCE mode J13 Closed Port 1 is in DTE mode J13 Open Pin 25 of port 1 is not connected J13A Open Pin 25 of port 1 is +9V DC J13A Closed Port 2 is in DCE mode J14 Closed Port 2 is in DTE mode J14 Open Pin 25 of port 2 is not connected J14A Open Pin 25 of port 2 is +9V DC J14A Closed Pin 1 of port 1 is capacitive ground JN1 Open Pin 1 of port 1 is galvanic ground JN1 Closed Pin 1 of port 2 is capacitive ground JN2 Open Pin 1 of port 2 is galvanic ground JN2 Closed Factory configured - do not alter J5 Unidentified Factory configured - do not alter J7 Unidentified Factory configured - do not alter J8 Unidentified ISDN INTERFACE TYPE Setting J11 J12 S-interface Pins 1 & 2 closed Pins 1 & 2 closed U-interface Pins 2 & 3 closed Pins 2 & 3 closed LINE TYPE Setting J1 J2 Public ISDN Open Open ISDN PBX Closed Open ISDN PBX with LLC Open Closed DIAGNOSTIC LED(S) LED1 Status Condition On Power is on Off Power is off Blinking ISDN failed LED2 Status LED3 Status LED4 Status Condition Off Off Off Normal operation for channel 1 On Off Off ISDN connection established on channel 1 Alternating Alternating Off Hotline call repetition in progress on channel 1 Blinking Blinking Off Hotline call repetition error on channel 1 Blinking Off Off Hotline active without connection on channel 1 On Off Off Profile editor in use locally on channel 1 On On On Profile editor password being entered on channel 1 On Blinking Blinking Profile editor in use remotely on channel 1 Off Off On Unable to determine correct connection rate on channel 1 Off On Off Buffer has overflowed on channel 1 Alternating Blinking Alternating Checksum error has been detected on channel 1 LED5 Status LED6 Status LED7 Status Condition Off Off Off Normal operation for channel 2 On Off Off ISDN connection established on channel 2 Alternating Alternating Off Hotline call repetition in progress on channel 2 Blinking Blinking Off Hotline call repetition error on channel 2 Blinking Off Off Hotline active without connection on channel 2 On Off Off Profile editor in use locally on channel 2 On On On Profile editor password being entered on channel 2 On Blinking Blinking Profile editor in use remotely on channel 2 Off Off On Unable to determine correct connection rate on channel 2 Off On Off Buffer has overflowed on channel 2 Alternating Blinking Alternating Checksum error has been detected on channel 2 LED2 LED3 LED4 LED5 LED6 LED7 Condition Blink Off Off Blink Off Off TA is resetting Proprietary AT Command Set AUTO-ANSWER TIME Type: Register Format: AT [cmds] S0=n [cmds] Default: Unidentified Range: 0-24 Unit: 5 seconds Description: Sets the amount of time that will elapse before the TA will answer an incoming call. When this value is set to 0 the TA will not automatically answer calls. A value of 1 will answer immediately. Values greater than 1 set the time to (n-1) * 5 seconds. CTS SIGNAL Type: Configuration Format: AT [cmds] &Rn [cmds] Description: Controls the operation of the Clear to Send signal. Command Function &R0 CTS follows RTS. &R1 CTS forced high. &R2 CTS follows V.110 flow control. FLOW CONTROL MODE Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Sets the type of flow control used. Command Function &K0 Flow control disabled. &K3 CTS/RTS flow control enabled. &K4 XON/XOFF flow control enabled. &K5 Flow control disabled. RESULT CODES Type: Register Format: AT [cmds] S15=n [cmds] Description: Enables caller ID information and extended result codes. Command Function S15=0 Caller ID information and extended result codes disabled. S15=1 Caller ID information enabled. S15=3 Caller ID information and extended result codes enabled. BIT-MAPPED REGISTER S14 Format: AT [cmds] S14=n [cmds] Default: Unidentified Range: 0-14 Description: Controls echo mode and result codes. Bit Value Function 0 0 Not used. 1 0 Command echo disabled. 1 Command echo enabled. 2 0 Result codes enabled. 1 Result codes disabled. 3 0 Numerical result codes enabled. 1 Verbose result codes enabled. Proprietary Command Set COMMAND ECHOING Type: Configuration Format: Jn Description: Selects whether commands will be echoed back to the DTE. Command Function J0 Command echoing disabled. J1 Command echoing enabled. CONNECTION SPEED Type: Configuration Format: Hn Description: Sets the speed of the remote connection. Command Function H1 Set speed to 300bps. H2 Set speed to 600bps. H3 Set speed to 1200bps. H4 Set speed to 2400bps. H5 Set speed to 4800bps. H6 Set speed to 9600bps. H7 Set speed to 19.2Kbps. H8 Set speed to 38.4Kbps. CHANGE PROFILE CHANNEL Type: Configuration Format: PROn Description: Selects which channel’s profile is being edited. Command Function PRO1 Edit profile for channel 1. PRO2 Edit profile for channel 2. CTS SIGNAL - NO CONNECTION Type: Configuration Format: NCTS 0xhh Description: Controls the behaviour of the CTS signal when there is no ISDN connection. Command Function NCTS 0x01 CTS is forced low. NCTS 0x02 CTS is forced high. NCTS 0x04 CTS follows DTR. NCTS 0x08 CTS follows RTS. NCTS 0x10 CTS is forced high during connection and negotiation only. NCTS 0x20 CTS follows remote DTR. NCTS 0x40 CTS follows remote RTS. NCTS 0x80 CTS follows V.110 flow control. CTS SIGNAL - NEGOTIATION Type: Configuration Format: WCTS 0xhh Description: Controls the behaviour of the CTS signal while dialing and negotiating a connection. Command Function WCTS 0x01 CTS is forced low. WCTS 0x02 CTS is forced high. WCTS 0x04 CTS follows DTR. WCTS 0x08 CTS follows RTS. WCTS 0x10 CTS is forced high during connection and synchronization only. WCTS 0x20 CTS follows remote DTR. WCTS 0x40 CTS follows remote RTS. WCTS 0x80 CTS follows V.110 flow control. CTS SIGNAL - CONNECTION Type: Configuration Format: CCTS 0xhh Description: Controls the behaviour of the CTS signal while connected. Command Function CCTS 0x01 CTS is forced low. CCTS 0x02 CTS is forced high. CCTS 0x04 CTS follows DTR. CCTS 0x08 CTS follows RTS. CCTS 0x10 CTS is forced high during connection and synchronization only. CCTS 0x20 CTS follows remote DTR. CCTS 0x40 CTS follows remote RTS. CCTS 0x80 CTS follows V.110 flow control. DATA LENGTH Type: Configuration Format: Ln Description: Selects how many data bits will be transmitted. Command Function L0 Synchronous mode. L7 7 data bits. L8 8 data bits. DATA PARITY Type: Configuration Format: Mn Description: Selects how many parity bits will be transmitted. Command Function M0 No parity. M1 Odd parity. M2 Even parity. DATA STOP Type: Configuration Format: Nn Description: Selects how many stop bits will be transmitted. Command Function M1 1 stop bit. M2 2 stop bits. DCD SIGNAL - NO CONNECTION Type: Configuration Format: NDCD 0xhh Description: Controls the behavior of the DCD signal when there is no ISDN connection. Command Function NDCD 0x01 DCD is forced low. NDCD 0x02 DCD is forced high. NDCD 0x04 DCD follows DTR. NDCD 0x08 DCD follows RTS. NDCD 0x10 DCD is forced high during connection and negotiation only. NDCD 0x20 DCD follows remote DTR. NDCD 0x40 DCD follows remote RTS. NDCD 0x80 DCD follows V.110 flow control. DCD SIGNAL - NEGOTIATION Type: Configuration Format: WDCD 0xhh Description: Controls the behavior of the DCD signal while dialing and negotiating a connection. Command Function WDCD 0x01 DCD is forced low. WDCD 0x02 DCD is forced high. WDCD 0x04 DCD follows DTR. WDCD 0x08 DCD follows RTS. WDCD 0x10 DCD is forced high during connection and synchronization only. WDCD 0x20 DCD follows remote DTR. WDCD 0x40 DCD follows remote RTS. WDCD 0x80 DCD follows V.110 flow control. DCD SIGNAL - CONNECTION Type: Configuration Format: CDCD 0xhh Description: Controls the behaviour of the DCD signal while connected. Command Function CDCD 0x01 DCD is forced low. CDCD 0x02 DCD is forced high. CDCD 0x04 DCD follows DTR. CDCD 0x08 DCD follows RTS. CDCD 0x10 DCD is forced high during connection and synchronization only. CDCD 0x20 DCD follows remote DTR. CDCD 0x40 DCD follows remote RTS. CDCD 0x80 DCD follows V.110 flow control. DEBUG PROFILE Type: Immediate Format: TEST Description: Displays the profile editor debug page. DIAL MODE Type: Configuration Format: En Description: Selects the dial mode the TA will use. Command Function E1 Manual dialing only; prompt for number will be displayed. E2 Asynchronous V.25bis dial mode. E3 Hotline dial mode; DTR is used for call signalling. E4 Hotline dial mode; RTS is used for call signalling. E5 Hotline dial mode; automatic dial attempt. E6 Incoming calls only. E7 Hayes dialing mode. E8 Synchronous V.25bis dial mode. DSR SIGNAL - NO CONNECTION Type: Configuration Format: NDSR 0xhh Description: Controls the behaviour of the DSR signal when there is no ISDN connection. Command Function NDSR 0x01 DSR is forced low. NDSR 0x02 DSR is forced high. NDSR 0x04 DSR follows DTR. NDSR 0x08 DSR follows RTS. NDSR 0x10 DSR is forced high during connection and negotiation only. NDSR 0x20 DSR follows remote DTR. NDSR 0x40 DSR follows remote RTS. NDSR 0x80 DSR follows V.110 flow control. DSR SIGNAL - NEGOTIATION Type: Configuration Format: WDSR 0xhh Description: Controls the behaviour of the DSR signal while dialing and negotiating a connection. Command Function WDSR 0x01 DSR is forced low. WDSR 0x02 DSR is forced high. WDSR 0x04 DSR follows DTR. WDSR 0x08 DSR follows RTS. WDSR 0x10 DSR is forced high during connection and synchronization only. WDSR 0x20 DSR follows remote DTR. WDSR 0x40 DSR follows remote RTS. WDSR 0x80 DSR follows V.110 flow control. DSR SIGNAL - CONNECTION Type: Configuration Format: CDSR 0xhh Description: Controls the behaviour of the DSR signal while connected. Command Function CDSR 0x01 DSR is forced low. CDSR 0x02 DSR is forced high. CDSR 0x04 DSR follows DTR. CDSR 0x08 DSR follows RTS. CDSR 0x10 DSR is forced high during connection and synchronization only. CDSR 0x20 DSR follows remote DTR. CDSR 0x40 DSR follows remote RTS. CDSR 0x80 DSR follows V.110 flow control. DTE/DCE MODE Type: Configuration Format: Sn Description: Sets whether the TA will operate as a DTE or a DCE device. Command Function S0 TA will operate as DCE. S1 TA will operate as DTE. DTR SIGNAL Type: Configuration Format: Dn Description: Controls the operation of the Data Terminal Ready signal. Command Function D0 Incoming calls accepted regardless of DTR state; low DTR does not disconnect. D1 Incoming calls accepted only if DTR is high; DTR or RTS transition to high will initiate a hotline call if in hotline mode; low DTR disconnects. D2 Incoming calls accepted only if DTR is high; high DTR or RTS will initiate a hotline call if in hotline mode; low DTR disconnects. D3 Incoming calls accepted regardless of DTR state; DTR or RTS transition to high will initiate a hotline call if in hotline mode; low DTR disconnects. D4 Incoming calls accepted regardless of DTR state; high DTR or RTS will initiate a hotline call if in hotline mode; low DTR disconnects. D5 Incoming calls accepted only if DTR is high; DTR or RTS transition to high will initiate a hotline call if in hotline mode; low DTR does not disconnect. D6 Incoming calls accepted only if DTR is high; high DTR or RTS will initiate a hotline call if in hotline mode; low DTR does not disconnect. EAZ Type: Configuration Format: An Description: Sets which incoming calls are answered. Command Function A0 All incoming calls are answered; all channels are notified of the call. A1 - A8 Only calls with a matching EAZ are answered. A9 All incoming calls are answered; only the channel matching the EAZ is notified of the call. EAZ - EDITOR Type: Configuration Format: Tn Description: Sets which incoming calls should be routed for remote configuration. Command Function T0 Only calls ending in "e" are routed to the editor. T1 - T8 Only calls with a matching EAZ are answered. T9 Calls matching the EAZ or ending in "e" are routed to the editor. ENTER PROFILE EDITOR Type: Immediate Description: Enters the profile editor so that changes may be made. Mode Command Manual dial V.25bis dial Hayes dial AT All other modes Push reset button, then EXIT PROFILE EDITOR Type: Immediate Format: EXIT Description: Quits the editor without saving changes. FLOW CONTROL MODE - DCE Type: Configuration Format: Bn Description: Sets the type of flow control used. Command Function B0 Flow control disabled. B1 XON/XOFF flow control enabled. B2 CTS flow control enabled. FLOW CONTROL MODE - DTE Type: Configuration Format: Cn Description: Sets the type of flow control used. Command Function C0 Flow control disabled. C1 XON/XOFF flow control enabled. C2 RTS flow control enabled. C3 DTR flow control enabled. HOTLINE NUMBER Type: Configuration Format: HOT <#> Description: Sets the number for hotline calling. If no number is given, hotline calling will not be allowed. INACTIVITY TIMER Type: Configuration Format: Fn Default: 0 Range: 0 - 60 Unit: 1 minute Description: Sets the amount of time that there must be no activity on the ISDN line before the TA disconnects. INCOMING CALL NUMBER Type: Configuration Format: RUFn <#> Description: Sets the number in position n of allowed incoming calls. LANGUAGE Type: Configuration Format: Kn Description: Selects the language the TA will display messages in. Command Function K0 Messages will be displayed in English. K1 Messages will be displayed in German. LINE TYPE Type: Configuration Format: Rn Description: Sets the type of line the TA will be operating on. Command Function R0 ISDN with BRI service. R1 Group 3 leased line service with 1TR6. R2 Group 2 leased line, 2B+D or B+D. R3 Group 0 leased line, single B channel only. R4 Point-to-point switched line. R5 Point-to-point group 3 leased line with 1TR6. LLC - INCOMING Type: Configuration Format: Pn Description: Sets the use of LLC for incoming DSS1 calls. Command Function P1 Only calls with matching LLC will be answered. P2 Ignore LLC when answering calls. P3 All data calls will be answered. P4 All calls will be answered. LLC - OUTGOING Type: Configuration Format: On Description: Sets the use of LLC for outgoing DSS1 calls. Command Function O1 Standard LLC enabled. O2 LLC disabled. O3 User-defined LLC enabled. LLC - USER-DEFINED DATA OCTET Type: Configuration Format: LLC=hh hh hh.. Description: Sets the user-defined LLC octets in hexadecimal. LOCAL SERIAL PORT SPEED Type: Configuration Format: Gn Description: Sets the speed of the serial port. Command Function G1 Set speed to 300bps. G2 Set speed to 600bps. G3 Set speed to 1200bps. G4 Set speed to 2400bps. G5 Set speed to 4800bps. G6 Set speed to 9600bps. G7 Set speed to 19.2Kbps. G8 Set speed to 38.4Kbps. LOCK SERIAL PORT SPEED Type: Configuration Format: In Description: Selects whether the serial port speed will be adjusted to the DTE speed. Command Function I0 Serial port speed locked. I1 Serial port speed will match DTE speed. MSN Type: Configuration Format: MALL <#>*n Description: Sets the MSN and subaddress for both channels of the TA and the editor. MSN - TA Type: Configuration Format: MTAX <#>*n Description: Sets the MSN and subaddress for both channels of the TA. MSN - EDITOR Type: Configuration Format: MEDX <#>*n Description: Sets the MSN and subaddress for both channels of the editor. MSN - EDITOR CHANNEL 1 Type: Configuration Format: MED1 <#>*n Description: Sets the MSN and subaddress for channel 1 of the editor. MSN - EDITOR CHANNEL 2 Type: Configuration Format: MED2 <#>*n Description: Sets the MSN and subaddress for channel 2 of the editor. MSN - TA CHANNEL 1 Type: Configuration Format: MTA1 <#>*n Description: Sets the MSN and subaddress for channel 1 of the TA. MSN - TA CHANNEL 2 Type: Configuration Format: MTA2 <#>*n Description: Sets the MSN and subaddress for channel 2 of the TA. NEXT PAGE Type: Immediate Format: NEXT Description: Shows the next page of values. PREVIOUS PAGE Type: Immediate Format: PREV Description: Shows the previous page of values. REMOTE CONFIGURATION PASSWORD Type: Configuration Format: PWD xxxx Description: Sets the password for remote configuration. If no password is given, no password will be required. RESET TO FACTORY DEFAULTS Type: Immediate Format: DEFA Description: Resets all settings to their factory defaults. SAVE PROFILE Type: Immediate Format: SAVE Description: Saves the current settings into the profile and quits the editor. SERVICE INDICATOR Type: Configuration Format: Pn Description: Sets the 1TR6 Service Indicator. Command Function P0 Service Indicator reports standard line. P1 Service Indicator reports Private SI. P2 Service Indicator reports Private 2. SERVICE INDICATOR DETAILS Type: Configuration Format: On Description: Sets the details for the 1TR6 Service Indicator. Pn Setting Command Function P0 O1 Service Indicator reports 1TR6. O2 Service Indicator reports X.21. O3 Service Indicator reports AOI synch/asynch mode. P1 O1 Service Indicator reports V.24 asynch. O2 Service Indicator reports 64Kbps asynch. O3 Service Indicator reports V.24 BTX. O4 Service Indicator reports V.24 Text. O5 Service Indicator reports 64Kbps PC-Net. P2 O1 Service Indicator reports Private 2 LLC with the data octet equal to 0. O2 Service Indicator reports Private 2 LLC with the data octet not equal to 0. O3 Service Indicator reports Private 2 with the data octet equal to 0. SYNCHRONOUS SPEED Type: Configuration Format: Qn Description: Selects what data rate the TA will operate in when in synchronous mode. Command Function Q0 Use V.24 asynchronous mode. Q1 Use data rate set with Gn and Hn. Q2 Use 64Kbps data rate. Q3 Use 56Kbps data rate. Q4 Use 48Kbps data rate. UPDATE PROFILE Type: Immediate Format: UPDA Description: Saves the current settings into the profile.