KINGSTON KFM-PC144 Card Type Fax, Modem (asynchronous) Chip Set Unidentified Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I Data Modulation Protocol Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis V1912 Proprietary AT Command Set AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %En [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled %E2 Auto-fallback/fall-forward enabled BIT-MAPPED REGISTER S14 Format: AT [cmds] S14=n [cmds] Default: 138 Range: 0-174 Unit: Bit-mapped Description: Controls echo, result codes and display, dial mode, and answer/originate mode. Bit Value Function 0 0 Not used 1 0 Command echo disabled 1 Command echo enabled 2 0 Result codes enabled 1 Result codes disabled 3 0 Display result codes in numeric format 1 Display result codes in verbose format 4 0 Not used 5 0 Tone dial enabled 1 Pulse dial enabled 6 0 Not used 7 0 Answer mode enabled 1 Originate mode enabled BIT-MAPPED REGISTER S21 Format AT [cmds] S21=n [cmds] Default: 52 Range: 0-252 Unit: Bit-mapped Description: Selects CTS/DCD/DSR signals, low DTR action, and the long space disconnect function. Bit Value Function 0, 1 00 Not used 2 0 CTS forced high 1 CTS follows RTS 4, 3 00 DTR signal ignored 01 Modem goes to command mode on low DTR 10 Modem disconnects on low DTR; Auto-Answer is disabled. 11 Modem is initialized on low DTR 5 0 DCD forced high 1 DCD normal 6 0 DSR forced high 1 DSR normal 7 0 Long space disconnect function disabled 1 Long space disconnect function enabled BIT-MAPPED REGISTER S22 Format AT [cmds] S22=n [cmds] Default: 117 Range: 0-127 Unit: Bit-mapped Description: Controls speaker volume and controls, and limits results codes. Bit Value Function 1, 0 00 Volume off 01 Low level volume 10 Medium level volume 11 High level volume 3, 2 00 Speaker off 01 Speaker off on carrier 10 Speaker always on 11 Speaker on during handshake 6 - 4 000 Basic result codes only enabled 100 Basic and connection speed result codes enabled 101 Basic and connection speed result codes and dialtone detection enabled 110 All result codes except dialtone detection enabled 111 All result codes enabled BIT-MAPPED REGISTER S23 Format AT [cmds] S23=n [cmds] Default: 183 Range: 0-189 Unit: Bit-mapped Description: Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone. Bit Value Function 0 0 Remote digital loopback denied 1 Remote digital loopback allowed 3 - 1 000 Sets serial port speed to 0-300bps 001 Sets serial port speed to 600bps 010 Sets serial port speed to 1200bps 011 Sets serial port speed to 2400bps 100 Sets serial port speed to 4800bps 101 Sets serial port speed to 9600bps 110 Sets serial port speed to 19200bps 5, 4 00 Parity even 01 Not used 10 Parity odd 11 No Parity 7, 6 00 Guard tone disabled 01 Guard tone disabled 10 Guard tone 1800Hz enabled BIT-MAPPED REGISTER S27 Format AT [cmds] S27=n [cmds] Default: 9 Range: 0-75 Unit: Bit-mapped Description: Selects asynchronous mode and ITU-T/Bell modes. Bit Value Function 3, 1, 0 000 Asynchronous mode, serial port speed follows connect speed 101 Error correction mode 111 Buffered asynchronous mode 5, 4, 2 000 Not used 6 0 ITU/T mode 1 Bell mode BIT-MAPPED REGISTER S28 Format AT [cmds] S28=n [cmds] Default: 0 Range: 0-128 Unit: Bit-mapped Description: Controls MNP10 link negotiation. Bit Value Function 5 - 0 000000 Not used 7, 6 00 Link will be negotiated at highest possible speed 01 Link will be negotiated at 1200bps 10 Link will be negotiated at 4800bps BIT-MAPPED REGISTER S31 Format: AT [cmds] S31=n [cmds] Default: 194 Range: 0-202 Description: Select auto-mode and extended result code format. Bit Value Function 0 0 Not used 1 0 Auto-mode detection disabled 1 Auto-mode detection enabled 3, 2 00 Enables CONNECT result codes to report DTE speed 01 Full reporting of CONNECT result codes 10 Enables CONNECT result codes to report DCE speed 7 - 4 1100 Not used BIT-MAPPED REGISTER S40 Format AT [cmds] S40=n [cmds] Default: 105 Range: 0-238 Unit: Bit-mapped Description: Controls MNP extended services, power level adjustment, break handling, and block size. Bit Value Function 0, 1 00 Conversion disabled 01 Conversion enabled 10 Conversion enabled except during LAPM answer detection phase. 2 0 Power level adjustment enabled 1 Power level adjustment disabled 5, 4, 3 000 \K0 001 \K1 010 \K2 011 \K3 100 \K4 101 \K5 7, 6 00 MNP block size is 64 characters 01 MNP block size is 128 characters 10 MNP block size is 192 characters 11 MNP block size is 256 characters BIT-MAPPED REGISTER S41 Format AT [cmds] S41=n [cmds] Default: 131 Range: 0-219 Unit: Bit-mapped Description: Selects compression, auto-retrain, flow control, MNP mode and MNP10 fallback. Bit Value Function 1, 0 00 Data compression disabled 01 MNP5 enabled 10 V.42bis enabled 11 MNP5 and V.42bis enabled 6, 2 00 Auto-retrain disabled 01 Auto-retrain enabled 10 Auto-fallback/fall-forward enabled 3 0 Flow control disabled 1 Flow control enabled 4 0 Stream mode for MNP 1 Block mode for MNP 5 0 Not used 7 0 MNP10 at 2400 and 1200bps disabled 1 MNP10 at 2400 and 1200bps enabled BIT-MAPPED REGISTER S201 Format: AT [cmds] S201=n [cmds] Default: 58 Range: 0-62 Description: Controls power level, and compromise equalizer. Bit Value Function 4 - 0 00000 Initial power level -26dBm 00001 Initial power level -30dBm 00010 Initial power level -10dBm ... ... 01010 Initial power level -10dBm 01011 Initial power level -11dBm ...to... ...to... 11010 Initial power level -26dBm ...to... ...to... 11110 Initial power level -30dBm 5 0 Equalizer disabled 1 Equalizer enabled BREAK SEND Type: Configuration Format: AT [cmds] \Bn [cmds] Default: 3 Range: 1-9 Unit: .1 second Description: Sends break to modem BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Description: Configures action of break signal Command Break from DTE Modem receives Break received \B from remote modem \K0 Online command Break sent to Buffers cleared, mode enabled, remote modem and break sent to DTE send no break buffered cleared to remote modem \K1 Break sent to Break sent to Buffers cleared, remote modem remote modem and break sent to DTE and buffered buffered cleared cleared \K2 Online command Send break to Break sent mode enabled, remote modem immediately to send no break immediately DTE to remote modem \K3 Send break to Send break to Break sent remote modem remote modem immediately to immediately immediately DTE \K4 Online command Send break with Break sent with mode enabled, transmitted data received data to send no break the DTE to remote modem \K5 Send break with Send break with Break sent with transmitted transmitted data received data to data the DTE COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 MNP5 enabled %C2 V.42bis enabled %C3 MNP5 and V.42bis enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Normal mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 MNP auto-reliable mode enabled DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Modifier Function L Re-dial last number P Pulse dialing enabled Sn Dial stored telephone number n (n=1-3) S=n Dial stored telephone number n (n=1-3) T Tone dialing enabled W Dialing resumed following dial tone detection , Dialing paused for amount of time specified in S8 register @ Wait for quiet answer ; Modem returned to command state after dialing ! Modem commanded to go on-hook for specified time before returning off-hook. ^ Calling tone disabled for this call only FLASH DIAL MODIFIER TIME Type: Register Format AT [cmds] S29=n [cmds] Default: 0 Range: 0-255 Unit: .01 second Description: Time the modem will go on-hook upon receiving the ! dial modifier in dial string. FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control Command Function \G0 Flow control disabled \G1 Flow control enabled FLOW CONTROL Type: Read-only Register Format AT [cmds] S39? [cmds] Description: Displays the current flow control Value Meaning 0 Flow control disabled 3 RTS/CTS flow control enabled 4 XON/XOFF flow control enabled 5 XON/XOFF and RTS/CTS flow control enabled FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S33=n [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S32=n [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON INACTIVITY TIMER Type: Register Format AT [cmds] S30=n [cmds] Default: 0 Range: 0-255 Unit: 10 seconds Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process. S30=0 will disable timer. LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %L [cmds] Description: Returns a value which indicates the received line signal level LINE SIGNAL QUALITY Type: Immediate Format: AT [cmds] %Q [cmds] Description: Returns a value which indicates line signal quality LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \Jn [cmds] Description: Sets operation of serial port speed Command Function \J0 Serial speed locked \J1 Serial speed follows connect speed MAXIMUM BLOCK SIZE FOR TRANSMISSION Type: Configuration Format: AT [cmds] \An [cmds] Description: Sets the maximum transmittable block size Command Function \A0 MNP block size is 64 characters \A1 MNP block size is 128 characters \A2 MNP block size is 192 characters \A3 MNP block size is 256 characters MNP - EXTENDED SERVICES Type: Configuration Format: AT [cmds] -Kn [cmds] Description: Controls conversion of a LAPM connection to MNP10 connection Command Function -K0 Conversion disabled -K1 Conversion enabled -K2 Conversion enabled except during LAPM answer detection phase. MNP - STREAM/BLOCK MODE Type: Configuration Format: AT [cmds] \Ln [cmds] Description: Selects the transfer mode for MNP link Command Function \L0 Stream mode for MNP enabled \L1 Block mode for MNP enabled MNP10 - FALLBACK Type: Configuration Format: AT [cmds] -Qn [cmds] Description: Allows MNP10 to fall back to speeds slower than 4800bps Command Function -Q0 MNP10 at 2400 and 1200bps disabled -Q1 MNP10 at 2400 and 1200bps enabled MNP10 - LINK NEGOTIATION Type: Configuration Format: AT [cmds] *Hn [cmds] Description: Sets the speed at which MNP10 link negotiation will occur Command Function *H0 Link will be negotiated at highest possible speed *H1 Link will be negotiated at 1200bps *H2 Link will be negotiated at 4800bps MNP10 - POWER LEVEL ADJUST Type: Configuration Format: AT [cmds] )Mn [cmds] Description: Controls automatic transmit power level adjustment during MNP 10 link negotiation Command Function )M0 Power level adjustment disabled )M1 Power level adjustment enabled REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports ROM checksum I2 Tests ROM and reports ‘OK’ or ‘ERROR’ I3 Reports ROM revision level I4 Reports modem identifier string I5 Report country code I6 Reports data pump model SLEEP TIMER Type: Register Format AT [cmds] S24=n [cmds] Default: 32 Range: 0-255 Unit: 1 second Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. S24=0 will disable timer. TEST MODES Type: Register Format: AT [cmds] S16=n [cmds] Default: 0 Range: 0-125 Unit: Bit-mapped Description: Controls loopback tests, analog, digital, remote digital, and self tests. Bit Value Function 0 0 Local analog loopback not in progress 1 Local analog loopback in progress 1 0 Not used 2 0 Local digital loopback not in progress 1 Local digital loopback in progress 3 0 Modem not in remote digital loopback 1 Remote digital loopback in progress 4 0 Remote digital loopback not requested 1 Remote digital loopback requested 5 0 Remote digital loopback w/ self-test not in progress 1 Remote digital loopback w/ self-test in progress 6 0 Local analog loopback w/ self-test not in progress 1 Local analog loopback w/ self-test in progress TRANSMISSION LEVEL - CELLULAR Type: Configuration Format: AT [cmds] @Mn [cmds] Default: 26 Range: 0-31 Unit: -1dBm Description: Sets the signal level for transmission while in cellular mode Command Function @M0 -26 dBm @M1 -30 dBm @M2-@M10 -10 dBm V.23 MODE Type: Configuration Format: AT [cmds] %Fn [cmds] Description: Selects V.23 split-speed and half-duplex Command Function %F1 75bps transmit, 1200bps receive (split-speed) %F2 1200bps transmit, 75bps receive (split-speed) V.32 - COMPROMISE EQUALIZER Type: Configuration Format: AT [cmds] :En [cmds] Description: Controls V.32 compromise equalizer Command Function :E0 Equalizer disabled :E1 Equalizer enabled