CREATIX POLYMEDIA UMC 14.4/VOICE (EXTERNAL) Card Type Modem (synchronous/asynchronous) Chip Set UMC I/O Options Voice Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus External Fax Class Class I & II Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis [Image] CONNECTIONS Function Label Function Label Line in CN1 DC power CN4 Line out CN2 Power switch SW1 RS-232/422 CN3 DIAGNOSTIC LED(S) LED Color Status Condition MR Red On Power is on MR Red Off Power is off TR Red On DTR signal is high TR Red Off DTR signal is low SD Red On Modem is transmitting data SD Red Off Modem is not transmitting data RD Red On Modem is receiving data RD Red Off Modem is not receiving data OH Red On Modem is off-hook OH Red Off Modem is on-hook CD Red On Carrier signal detected CD Red Off Carrier signal not detected AA Red On Auto-answer enabled AA Red Off Auto-answer disabled EC Red On Error correction is in progress EC Red Off Error correction is not in progress Proprietary AT Command Set ACCEPT RELIABLE MODE Type: Immediate Format: AT [cmds] \U [cmds] Description: Accepts remote modem’s request for a reliable mode connection ADAPTIVE HANDSHAKE Type: Configuration Format: AT [cmds] *Gn [cmds] Description: Sets adaptive handshaking Command Function *G0 Adaptive handshake disabled *G1 Adaptive handshake enabled AUTO-RELIABLE FALLBACK CHARACTER Type: Configuration Format: AT [cmds] %An [cmds] Default: Unidentified Range: 0-127 Unit: ASCII Description: Sets the character used as the auto-reliable fallback character. %A0 will disable this function. AUTO-RELIABLE TIME BUFFER CONFIGURATION Type: Configuration Format: AT [cmds] \Cn [cmds] Description: Controls the handling of incoming data during auto-reliable time period Command Function \C0 Data is discarded \C1 Data is buffered \C2 Data is discarded, modem returns to normal mode on receiving auto-reliable fallback character. AUTO-RETRAIN Type: Configuration Format: AT [cmds] *Tn [cmds] Description: Selects auto-retrain mode Command Function *T0 Auto-retrain disabled *T1 Auto-retrain enabled BIT MAPPED REGISTERS Register Default S14 Unidentified S16 Unidentified S21 Unidentified S22 Unidentified S23 Unidentified S27 Unidentified BREAK SEND Type: Configuration Format: AT [cmds] \Bn [cmds] Default: 3 Range: 0-9 Unit: .1 second Description: Sends break to modem BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Default: 5 Range: 0-5 Unit: Unidentified Description: Configures action of break signal BUSY TONE FILTER Type: Register Format: AT [cmds] S96=n [cmds] Description: Selects the busy tone filter COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects MNP5 data compression Command Function %C0 Data compression disabled %C1 Data compression enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Sets connect mode Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP mode only enabled \N3 MNP/Normal automode enabled \N4 LAP-M mode only enabled \N5 LAP-M/MNP/Normal automode enabled \N6 LAP-M mode without phase detection enabled \N7 LAP-M/MNP/Normal automode without phase detection enabled CONNECTION SPEED Type: Configuration Format AT [cmds] *Nn [cmds] Description: Selects modem connection speed Command Function *N0 Select connection speed at 1200bps speed *N1 Select connection speed at 2400bps speed *N2 Select connection speed at 4800bps speed *N3 Select connection speed at 9600bps speed *N4 Select connection speed at 7200bps speed *N5 Select connection speed at 12Kbps speed *N6 Select connection speed at 14.4Kbps speed *N7 Select connection speed at V.23 ENERGY DETECTION THRESHOLD Type Register Format AT [cmds] S97=n [cmds] Default Unidentified Range Unidentified Unit Unidentified Description Enables energy detection threshold EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Extended result codes disabled \V1 Extended result codes enabled FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control Command Function \G0 Flow control disabled \G1 Flow control enabled FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 XON/XOFF flow control enabled \Q2 CTS flow control to DTE enabled \Q3 RTS/CTS flow control enabled INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Default: 0 Range: 0-90 Unit: 1 minutes Description: Sets the length of time that the modem does not receive information before it disconnects INITIATE RELIABLE MODE Type: Immediate Format: AT [cmds] \O [cmds] Description: During normal mode the modem initiates a reliable mode connection LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \Jn [cmds] Description: Sets operation of serial port speed Command Function \J0 Serial speed locked \J1 Serial speed follows connect speed MAXIMUM BLOCK SIZE FOR TRANSMISSION Type: Configuration Format: AT [cmds] \An [cmds] Description: Sets the maximum transmittable block size Command Function \A0 MNP block size is 64 characters \A1 MNP block size is 128 characters \A2 MNP block size is 192 characters \A3 MNP block size is 256 characters XON/XOFF PASS-THROUGH Type: Configuration Format: AT [cmds] \Xn [cmds] Description: Selects whether XON/XOFF signals are sent to remote modem Command Function \X0 XON/XOFF signals trapped by local modem \X1 XON/XOFF passed through local modem