BEST DATA PRODUCTS, INC. 9624 FQ Modem Type Data (synchronous/asynchronous)/Fax Maximum Data Rate 2400bps Maximum Fax Rate 9600bps Data Bus 8-bit ISA Fax Class Class 1 Data Modulation Protocol Bell 103 & 212A ITU-T V.21 & V.22/V.22bis Fax Modulation Protocol Unidentified Error Correction/Compression Unidentified [Image] CONNECTIONS Purpose Location Purpose Location Line-in or line-out CN1 Line-in or line-out CN2 PORT CONFIGURATION - JP1 COM/IRQ Jumper Jumper Jumper Jumper Jumper Jumper A B C D E F » COM2/IRQ3 Open Closed Closed Open Open Closed COM1/IRQ4 Closed Open Open Closed Open Closed COM3/IRQ4 Closed Open Open Closed Closed Open COM4/IRQ3 Open Closed Closed Open Closed Open %J - PROPRIETARY COMMAND Type: Immediate Format: %Jn [cmds] Example: %J Description Resets the configuration to the &F profile with the following exceptions: Command/Register %J Configuration: %Dn Sets DTMF attenuation to 2dB (%D1). %Ln Sets attenuation to 6dB (%L3). S6 Wait for dial tone set to 3 seconds (S3 = 3). S11 DTMF tone duration set to 95ms (S11 = 95). %D - PROPRIETARY COMMAND Type: Configuration Format: AT [cmds] %Dn [cmds] Example: AT M3 %D3 D5555555 Description Sets the DTMF transmit level attenuation. Command Function %D0 0dB attenuation. » %D1 2dB attenuation. %D2 4dB attenuation. %D3 6dB attenuation. %D4 8dB attenuation. %D5 10dB attenuation. %D6 12dB attenuation. %D7 14dB attenuation. %L - PROPRIETARY COMMAND Type: Configuration Format: AT [cmds] %Ln [cmds] Example: AT M3 %L5 D5555555 Description Sets the transmit level attenuation. Command Function %L0 0dB attenuation. %L1 2dB attenuation. %L2 4dB attenuation. » %L3 6dB attenuation. %L4 8dB attenuation. %L5 10dB attenuation. %L6 12dB attenuation. %L7 14dB attenuation. S21 - PROPRIETARY BIT-MAPPED REGISTER Value Range: Bit-mapped Default: 0 Type: Read/Write In Stored Profile?: Yes Description: Bit-mapped configuration register. Bit Value Function 0 » 0 RJ-11/RJ-41S/RJ-45S-type jack used. 1 RJ-12/RJ-13-type jack used. 1 » 0 Not used. 2 » 0 CTS signal follows RTS signal. 1 CTS signal follows DCD signal. 4, 3 » 00 Modem ignores DTR signal. 01 Modem switches to command mode when a DTR signal is detected. 10 Modem hangs up when a DTR signal is 11 detected. Modem resets to &F defaults when a DTR signal is detected. 5 » 0 DCD enabled. 1 DCD enabled when a carrier signal is detected, disabled when carrier signal is lost. 6 » 0 DSR enabled. 1 Modem goes off-hook in data mode only. 7 » 0 Long-space disconnect function disabled (Y0). 1 Long-space disconnect function enabled (Y1). S27 - PROPRIETARY BIT-MAPPED REGISTER Value Range: Bit-mapped Default: 0 Type: Read/Write In Stored Profile?: Yes Description: Bit-mapped configuration register. Bit Value Function 1,0 » 00 Asynchronous mode enabled. 01 Not used. 10 Not used. 11 Not used. 2 » 0 Dial-up line mode enabled. 1 Leased-line mode enabled. 4,3 » 00 Transmit clock generated by the modem. 01 Not used. 10 Not used. 11 Not used. 5 » 0 CCITT V.22/V.22bis protocols enabled. 1 Bell 212A protocol enabled. 6 » 0 Not used. 7 » 0 Not used. S22 - PROPRIETARY BIT-MAPPED REGISTER Value Range: Bit-mapped Default: 118 Type: Read/Write In Stored Profile?: Yes Description: Bit-mapped configuration register. Bit Value Function 1, 0 » 10 Speaker set to medium volume. 00 Not used. 01 Speaker set to low volume. 11 Speaker set to high volume. 3,2 » 01 Speaker enabled while dialing, enabled until carrier signal is detected, then 00 disabled. 10 Speaker disabled. 11 Speaker enabled. Speaker disabled while dialing, enabled until carrier signal is detected, then disabled. 6,5,4 » 111 Full result codes, dial tone wait, and busy tone detect enabled. 000 Basic result codes enabled, blind 001 dialing only. 010 Not used. 011 Not used. 100 Not used. 101 Full result codes enabled, blind dialing only. 110 Full result codes and dial tone wait enabled. Full result codes enabled, blind dialing only, busy tone detect enabled. 7 » 0 39/61 make/break ratio enabled. 1 33/67 make/break ratio enabled. S23 - PROPRIETARY BIT-MAPPED REGISTER Value Range: Bit-mapped Default: 7 Type: Read/Write In Stored Profile?: Yes Description: Bit-mapped configuration register. Bit Value Function 0 » 1 Grant remote loopback request. 0 Ignore remote loopback request. 2,1 » 11 2400bps data rate enabled. 00 0 - 300bps data rate enabled. 01 600bps data rate enabled. 10 1200bps data rate enabled. 3 » 0 Not used. 5,4 » 00 Even parity enabled. 01 Space parity enabled. 10 Odd parity enabled. 11 Parity disabled. 7,6 » 00 Guard tone disabled. 01 550Hz guard tone enabled. 10 1800Hz guard tone enabled. 11 Not used. S28 - PROPRIETARY BIT-MAPPED REGISTER Value Range: Bit-mapped Default: 140 Type: Read/Write In Stored Profile?: Yes Description: Bit-mapped configuration register. Bit Value Function 2,1,0 000 0dB transmit level attenuation selected. 001 2dB transmit level attenuation selected. 010 4dB transmit level attenuation selected. 011 6dB transmit level attenuation selected. » 100 8dB transmit level attenuation selected. 101 10dB transmit level attenuation selected. 110 12dB transmit level attenuation selected. 111 14dB transmit level attenuation selected. 5,4,3 000 0dB transmit level attenuation selected. » 001 2dB transmit level attenuation selected. 010 4dB transmit level attenuation selected. 011 6dB transmit level attenuation selected. 100 8dB transmit level attenuation selected. 101 10dB transmit level attenuation selected. 110 12dB transmit level attenuation selected. 111 14dB transmit level attenuation selected. 6 » 0 10 pulses per second dial signal enabled. 1 20 pulses per second dial signal enabled. 7 » 1 %J resets secondary default. 0 &F resets secondary default.