SILICOM CONNECTIVITY SOLUTIONS, INC. ETHERMODEM PCMCIA ADAPTER Card Type Fax, Modem (synchronous/asynchronous), Network Interface Card Chip Set Unidentified NIC Type Ethernet Maximum Network Rate 10Mbps Maximum Modem Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I & II Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP10, V.42bis Topology Linear Bus, Star Wiring Type Unshielded twisted pair RG-58A/U 50ohm coaxial Boot ROM Not available [Image] CONNECTIONS Function Label Function Label Line out - RJ-11 CN1 10Base-2 - RG-58A/U CN3 10Base-T - RJ-45 CN2 DIAGNOSTIC LED(S) LED Color Status Condition LED 1 Green On Data is transmitted LED 1 Green Off Data is not transmitted LED 2 Yellow On 10Base-T link integrity exists LED 2 Yellow Off 10Base-T link integrity broken Proprietary AT Command Set AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %E n [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled %E2 Auto-fallback/fall-forward enabled BIT-MAPPED REGISTERS Register Default S14 Unidentified S16 Unidentified S21 Unidentified S22 Unidentified S23 Unidentified S27 Unidentified S28 Unidentified S31 Unidentified S39 Unidentified S40 Unidentified S41 Unidentified S201 Unidentified S202 Unidentified BREAK SEND Type: Configuration Format: AT [cmds] \B n [cmds] Default: Unidentified Range: Unidentified Unit: .1 second Description: Sends break to modem BREAK TYPE Type: Configuration Format: AT [cmds] \K n [cmds] Description: Configures action of break signal Command Break from DTE Modem receives Break received \B from remote modem \K0 Online command mode Break sent to Buffers enabled, send no remote modem cleared, break break to remote and buffered sent to DTE modem cleared \K1 Break sent to remote Break sent to Buffers modem and buffered remote modem cleared, break cleared and buffered sent to DTE cleared \K2 Online command mode Send break to Break sent enabled, send no remote modem immediately to break to remote immediately DTE modem \K3 Send break to remote Send break to Break sent modem immediately remote modem immediately to immediately DTE \K4 Online command mode Send break Break sent enabled, send no with with received break to remote transmitted data to the modem data DTE \K5 Send break with Send break Break sent transmitted data with with received transmitted data to the data DTE CALLER ID Type: Configuration Format: AT [cmds] #CID= n [cmds] Description: Controls the Caller ID function Command Function #CID=0 Caller ID disabled #CID=1 Caller ID displays formatted data #CID=2 Caller ID displays raw hexadecimal data COMPRESSION Type: Configuration Format: AT [cmds] %C n [cmds] Description: Selects data compression Command Function %C0 Data compression enabled %C1 MNP5 enabled %C2 V.42bis enabled %C3 MNP5 and V.42bis enabled CONNECT MODE Type: Configuration Format: AT [cmds] \N n [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 Force LAP-M mode \N5 Force MNP mode FLASH DIAL MODIFIER TIME Type: Register Format AT [cmds] S29= n [cmds] Default: Unidentified Range: Unidentified Unit: Unidentified Description: Time the modem will go on-hook upon receiving the ! dial modifier in dial string. FLOW CONTROL Type: Configuration Format: AT [cmds] \G n [cmds] Description: Selects modem port flow control Command Function \G0 Flow control disabled \G1 Flow control enabled FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S33= n [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S32= n [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %L [cmds] Description: Returns a value which indicates the received line signal level LINE SIGNAL QUALITY Type: Immediate Format: AT [cmds] %Q [cmds] Description: Returns a value which indicates line signal quality MAXIMUM BLOCK SIZE FOR TRANSMISSION Type: Configuration Format: AT [cmds] \A n [cmds] Description: Sets the maximum transmittable block size Command Function \A0 MNP block size is 64 characters \A1 MNP block size is 128 characters \A2 MNP block size is 192 characters \A3 MNP block size is 256 characters MNP - STREAM/BLOCK MODE Type: Configuration Format: AT [cmds] \L n [cmds] Description: Selects the transfer mode for MNP link Command Function \L0 Stream mode for MNP enabled \L1 Block mode for MNP enabled MNP10 - COMPRESSION Type: Configuration Format: AT [cmds] -K n [cmds] Description: Selects MNP10 data compression Command Function -K0 MNP10 disabled -K1 MNP10 enabled -K2 MNP10 enabled on originate mode only MNP10 - FALLBACK Type: Configuration Format: AT [cmds] -Q n [cmds] Description: Allows MNP10 to fall back to speeds slower than 4800bps Command Function -Q0 MNP10 at 2400 and 1200bps disabled -Q1 MNP10 at 2400 and 1200bps enabled MNP10 - LINK NEGOTIATION Type: Configuration Format: AT [cmds] *H n [cmds] Description: Sets the speed at which MNP10 link negotiation will occur Command Function *H0 Link will be negotiated at highest possible speed *H1 Link will be negotiated at 1200bps *H2 Link will be negotiated at 4800bps MNP10 - POWER LEVEL ADJUST Type: Configuration Format: AT [cmds] )M n [cmds] Description: Controls automatic transmit power level adjustment during MNP 10 link negotiation Command Function )M0 Power level adjustment disabled )M1 Power level adjustment enabled SLEEP TIMER Type: Register Format AT [cmds] S24= n [cmds] Default: 1 Range: 0-255 Unit: .01 second Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. TEST MODE - PTT Type: Immediate Format: AT [cmds] %TT n [cmds] Description: Send PTT test signals for a line tests TRANSMISSION LEVEL Type: Configuration Format: AT [cmds] @M n [cmds] Default: Unidentified Range: Unidentified Unit: -1 dBm Description: Sets the signal level for transmission over switched phone lines TRANSMISSION LEVEL - FAX Type: Register Format: AT [cmds] S92= n [cmds] Default: 10 Range: 1-15 Unit: -1 dBm Description: Sets the signal level for transmission while in fax mode TRANSMISSION LEVEL - CELLULAR Type: Register Format: AT [cmds] S201= n [cmds] Default: 10 Range: 0-15 Unit: -1 dBm Description: Sets the signal level for transmission while in cellular mode TRANSMISSION LEVEL - LEASED-LINE Type: Register Format: AT [cmds] S99= n [cmds] Default: 10 Range: 0-15 Unit: -1 dBm Description: Sets the signal level for transmission over leased-lines TRANSMISSION LEVEL - PSTN Type Register or Configuration Format AT [cmds] S91 =n [cmds] Default 10 Range 1-15 Unit -1 dBm Description Sets the signal level for transmission over switched phone lines V.32 - COMPROMISE EQUALIZER Type: Configuration Format: AT [cmds] :E n [cmds] Description: Controls V.32 compromise equalizer Command Function :E0 Equalizer disabled :E1 Equalizer enabled