STAR LOGIC, INC. RM2422E Card Type Fax, Modem (asynchronous), Network Interface Card Chip Set Rockwell Maximum Network Rate 10Mbps Maximum Modem Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I & II Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42bis Topology Star Wiring Type Unshielded twisted pair Boot ROM Not available [Image] CONNECTIONS Function Label Function Label Line out - RJ-11 CN1 10Base-T network CN2 connection - RJ-45 DIAGNOSTIC LED(S) LED Color Status Condition 1 Red On Twisted pair network connection is good 1 Red Off Twisted pair network connection is broken Proprietary AT Command Set AUDIO OUTPUT LEVEL Type Configuration Format AT [cmds] #TL n [cmds] Default 32767 Range 0-32767 Unit Unidentified Description Sets the transmit level of the data pump audio output AUTO-RETRAIN - FALLBACK/FALL-FORWARD Type: Configuration Format: AT [cmds] %E n [cmds] Description: Controls auto-retrain mode and fallback/fall-forward Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled » %E2 Auto-fallback/fall-forward enabled BAUD RATE Type Configuration Format AT [cmds] #BDR= n [cmds] Default 0 Range 0-48 Unit current speed Description Selects a baud rate without speed detection at the serial port. #BDR=0, Enables autobaud detection BEEP TONE TIMER Type Configuration Format AT [cmds] #VBT= n [cmds] Default 10 Range 0-40 Unit .1 second Description Sets the time period which is used by the modem as the DTMF for generating tones while in on-line voice command mode. BIT-MAPPED REGISTER S14 Format AT [cmds] S14= n [cmds] Default: 138 Range: 0-255 Unit: Bit-mapped Description: Controls echo, result codes, result code display, dial mode, and answer/originate mode. Bit Value Function 0 0 Not used 1 0 Command echo disabled 1 Command echo enabled 2 0 Result codes enabled 1 Result codes disabled 3 0 Display result codes in numeric 1 format Display result codes in verbose format 4 0 Not used 5 0 Tone dial enabled 1 Pulse dial enabled 6 0 Not used 7 0 Answer mode enabled 1 Originate mode enabled BIT-MAPPED REGISTER S21 Format AT [cmds] S21= n [cmds] Default: 4 Range: 0-253 Unit: Bit-mapped Description: Selects jack type, CTS signal, low DTR action, DCD signal, DSR signal, and the long space disconnect function. Bit Value Function 0 0 Selects RJ-11, RJ-41S, or RJ45S jack 1 Selects RJ-12 or RJ-13 jack 1 0 Not used 2 0 CTS follows RTS 1 CTS forced high 4, 3 00 DTR signal ignored 01 Modem goes to command mode on low DTR 10 Modem disconnects on low 11 DTR. Auto-Answer is disabled. Modem is initialized on low DTR 5 0 DCD forced high 1 DCD normal 6 0 DSR forced high 1 DSR normal 7 0 Long space disconnect function disabled 1 Long space disconnect function enabled BIT-MAPPED REGISTER S22 Format AT [cmds] S22= n [cmds] Default: 117 Range: 0-127 Unit: Bit-mapped Description: Controls speaker volume and controls, and limits results codes. Bit Value Function 1, 0 00 Off volume 01 On volume 10 Medium level volume 11 High level volume 3, 2 00 Speaker off 01 Speaker off on carrier 10 Speaker always on 11 Speaker on during handshake 6, 5, 4 000 Basic result codes only enabled 100 Basic and connection 101 speed result codes enabled 110 Basic and connection 111 speed result codes and dialtone detection enabled All result codes except dialtone detection enabled All result codes enabled BIT-MAPPED REGISTER S23 Format AT [cmds] S23= n [cmds] Default: 54 Range: 0-255 Unit: Bit-mapped Description: Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone. Bit Value Function 0 0 Remote digital loopback denied 1 Remote digital loopback allowed 3, 2, 1 000 Sets serial port speed to 0-300bps 001 Sets serial port 010 speed to 600bps 011 Sets serial port speed to 1200bps 100 Sets serial port 101 speed to 2400bps 110 Sets serial port speed to 4800bps 111 Sets serial port speed to 9600bps Sets serial port speed to 19200bps Sets serial port speed to 38400bps 5,4 00 Parity even 01 Not used 10 Parity odd 11 No Parity 7, 6 00 Guard tone disabled 01 Guard tone disabled 10 Guard tone 1800Hz enabled BIT-MAPPED REGISTER S27 Format AT [cmds] S27= n [cmds] Default: Unidentified Range: Unidentified Unit: Bit-mapped Description: Selects ITU-T/Bell modes Bit Value Function 5 - 0 N/A Not used 6 0 CCITT mode 1 Bell mode BIT-MAPPED REGISTER S28 Format AT [cmds] S28= n [cmds] Default: 0 Range: 0-255 Unit: Bit-mapped Description: Controls pulse dialing and link negotiation. Bit Value Function 2 - 0 0 Not used 4, 3 00 39ms make/61ms break at 10pps 01 33ms make/67ms break 10 at 10pps 11 39ms make/61ms break at 20pps 33ms make/67ms break at 20pps 5 0 Not used 7, 6 00 Link will be negotiated at highest 01 possible speed 10 Link will be negotiated at 1200bps Link will be negotiated at 4800bps BIT-MAPPED REGISTER S31 Format AT [cmds] S31= n [cmds] Default: 2 Range: 0-9 Unit: Bit-mapped Description: Controls auto-baud function and connect message result codes Bit Value Function 0 0 Not used 1 0 Auto-baud disabled 1 Auto-baud enabled 3, 2 00 DTE speed displayed in result codes 01 Extended result codes 10 enabled; DCE speed displayed in result codes DCE speed displayed in result codes BIT-MAPPED REGISTER S39 Format AT [cmds] S39= n [cmds] Default: 0 Range: 0-5 Unit: Bit-mapped Description: Controls flow control Bit Value Function 2, 1, 0 000 Flow control disabled. 011 RTS/CTS flow control enabled 100 XON/XOFF flow control 101 enabled. Both XON/XOFF and RTS/CTS flow control enabled BIT-MAPPED REGISTER S40 Format AT [cmds] S40= n [cmds] Default: 105 Range: 0-255 Unit: Bit-mapped Description: Controls break handling; selects MNP extended services, and block size. Bit Value Function 0 0 MNP10 disabled 1 MNP10 enabled 2 - 1 0 Not used 5, 4, 3 000 \K0 001 \K1 010 \K2 011 \K3 100 \K4 101 \K5 7, 6 00 MNP block size is 64 characters 01 MNP block size is 128 10 characters 11 MNP block size is 192 characters MNP block size is 256 characters BIT-MAPPED REGISTER S41 Format AT [cmds] S41= n [cmds] Default: 3 Range: 0-15 Unit: Bit-mapped Description: Selects compression, auto-retrain, flow control, and MNP10 fall back. Bit Value Function 0 0 Data compression disabled 1 Data compression enabled 1 0 Auto-retrain disabled 1 Auto-retrain enabled 2 0 Flow control disabled 1 Flow control enabled 3 0 MNP10 at 2400 and 1200bps disabled 1 MNP10 at 2400 and 1200bps enabled BITS PER SAMPLE Type: Configuration Format: AT [cmds] #VBS= n [cmds] Description: Selects the type of voice compression to be used; ADPCM or linear PCM . Command Function #VBS=2 2 bits per sample ADPCM enabled » #VBS=4 4 bits per sample ADPCM enabled #VBS=8 8 bits per sample PCM enabled Note: Use with #VSR=7200 or 11025 BREAK SEND Type: Configuration Format: AT [cmds] \B n [cmds] Default: Unidentified Range: Unidentified Unit: .1 second Description: Sends break to modem BREAK TYPE Type: Configuration Format: AT [cmds] \K n [cmds] Description: Configures action of break signal Command Break from DTE Modem Break received receives \B from remote modem \K0 Online command Break sent to Buffers mode enabled, send remote modem cleared, break no break to remote and buffered sent to DTE modem cleared \K1 Break sent to Break sent to Buffers remote modem and remote modem cleared, break buffered cleared and buffered sent to DTE cleared \K2 Online command Send break to Break sent mode enabled, send remote modem immediately to no break to remote immediately DTE modem \K3 Send break to Send break to Break sent remote modem remote modem immediately to immediately immediately DTE \K4 Online command Send break Break sent mode enabled, send with with received no break to remote transmitted data to the modem data DTE » \K5 Send break with Send break Break sent transmitted data with with received transmitted data to the data DTE BUFFER SKID Type Configuration Format AT [cmds] #VSK= n [cmds] Default 255 Range 255 Unit 1 byte Description The modem searches for spare space in the voice transmit buffer after the XOFF threshold is reached, during voice transmission. Note: Buffer skid is the amount of data the DTE can continue to send after being commanded to stop sending data by the modem. BUFFER SIZE Type: Immediate Format: AT [cmds] #VBQ? [cmds] Description: Returns the size of the voice transmit and receive buffers CALLER ID Type: Configuration Format: AT [cmds] %CID= n [cmds] Description: Controls the Caller ID function Command Function %CID=0 Caller ID disabled %CID=1 Caller ID displays formatted data %CID=2 Caller ID displays raw hexadecimal data CALLER ID MODE Type: Immediate Format: AT [cmds] %CID=? [cmds] Description: Retrieves the current Caller ID mode from the modem COMPRESSION Type: Configuration Format: AT [cmds] %C n [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 MNP5 enabled %C2 V.42bis enabled %C3 MNP5 and V.42bis enabled CONNECT MODE Type: Configuration Format: AT [cmds] \N n [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enable \N1 Normal mode enable \N2 Reliable mode enable \N3 Auto-reliable mode enable \N4 LAP-M mode only enable \N5 MNP mode only enable DTMF TONE REPORTING Type: Configuration Format: AT [cmds] #VTD= n [cmds] Default: Unidentified Range: Unidentified Description: Selects which types of tones can be detected and reported to the DTE via shielded codes in voice transmit, voice receive, and on-line voice command modes. Bit Value Function 0 0 DTMF tone capability disabled 1 DTMF tone capability enabled 1 0 V.25 1300 Hz Calling tone capability disabled 1 V.25 1300 Hz Calling tone capability enabled 2 0 T.30 1100 Hz Facsimile Calling tone capability 1 disabled T.30 1100 Hz Facsimile Calling tone capability enabled 3 0 V.25/T.30 2100 Hz Answer tone capability disabled 1 V.25/T.30 2100 Hz Answer tone capability enabled 4 0 Bell 2225 Hz Answer tone capability disabled 1 Bell 2225 Hz Answer tone capability enabled 5 0 Call progress tone and cadence capability 1 disabled call progress tone and cadence capability enabled Note: The modem detects this tone and reports it via a shielded code to the DTE. Tone detection is only performed when the sampling rate is 7.2KHz FLASH DIAL MODIFIER TIME Type: Register Format AT [cmds] S29= n [cmds] Default: 0 Range: 0-255 Unit: .01 second Description: Time the modem will go on-hook upon receiving the ! dial modifier in dial string FLASH MEMORY - DOWNLOAD Type: Immediate Format: AT [cmds] ** n [cmds] Description: Downloads new firmware to flash memory Command Function **0 Download at last used serial port speed **1 Download at 38.4bps **2 Download at 57.6bps FLOW CONTROL Type: Configuration Format: AT [cmds] \G n [cmds] Description: Selects modem port flow control Command Function » \G0 Flow control disabled \G1 Flow control enabled FLOW CONTROL CHARACTER - XOFF Type: Register Format: AT [cmds] S33= n [cmds] Default: 19 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XOFF FLOW CONTROL CHARACTER - XON Type: Register Format: AT [cmds] S32= n [cmds] Default: 17 Range: 0-255 Unit: ASCII Description: Sets the character used to represent XON GENERATE TONE SIGNALS - ONLINE VOICE COMMAND Type: Configuration Format: AT [cmds] #VTS [cmds] Description: Controls which tones will be issued, DTMF or other tones, when modem is in on-line voice command Mode and the sampling rate is set to 7.2 kHz. IDENTIFY COMPRESSION Type: Immediate Format: AT [cmds] #VCI? [cmds] Description: Returns a unique character string which is used for identifying proprietary compression methods of Rockwell ADPCM. LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %L [cmds] Description: Returns a value which indicates the received line signal level LINE SIGNAL QUALITY Type: Immediate Format: AT [cmds] %Q [cmds] Description: Returns a value which indicates the line signal quality MAXIMUM BLOCK SIZE FOR TRANSMISSION Type: Configuration Format: AT [cmds] \A n [cmds] Description: Sets the maximum transmittable block size Command Function \A0 MNP block size is 64 characters \A1 MNP block size is 128 characters \A2 MNP block size is 192 characters \A3 MNP block size is 256 characters MNP10 - COMPRESSION Type: Configuration Format: AT [cmds] -K n [cmds] Description: Selects MNP10 data compression Command Function -K0 MNP10 disabled -K1 MNP10 enabled -K2 MNP10 enabled on originate mode only MNP10 - FALLBACK Type: Configuration Format: AT [cmds] -Q n [cmds] Description: Allows MNP10 to fallback to speeds slower than 4800bps Command Function -Q0 MNP10 at 2400 and 1200bps disabled -Q1 MNP10 at 2400 and 1200bps enabled MNP10 - LINK NEGOTIATION Type: Configuration Format: AT [cmds] *H n [cmds] Description: Sets the speed at which MNP10 link negotiation will occur Command Function *H0 Link will be negotiated at highest possible speed *H1 Link will be negotiated at 1200bps *H2 Link will be negotiated at 4800bps MNP10 - POWER LEVEL ADJUST Type: Configuration Format: AT [cmds] )M n [cmds] Description: Controls automatic transmit power level adjustment during MNP 10 link negotiation Command Function )M0 Power level adjustment disabled )M1 Power level adjustment enabled )M2 Power level adjustment enabled except during MNP link negotiation MODE SELECTION Type: Configuration Format: AT [cmds] #CLS= n [cmds] Description: Select data, fax or voice/audio mode while in any mode. Command Function #CLS=0 Data mode enabled #CLS=1 Fax Class 1 mode enabled #CLS=2 Fax Class 2 mode enabled #CLS=8 Voice/Audio mode enabled PLAYBACK VOLUME CONTROL Type: Configuration Format: AT [cmds] #VGT [cmds] Default: 153 Range: 128-228 Unit: Unidentified Description: Sets the volume on playback during command mode REPORT MODEL Type: Immediate Format: AT [cmds] #MDL? [cmds] Description: Displays the model number of the modem REPORT MANUFACTURER Type: Immediate Format: AT [cmds] #MFR? [cmds] Description: Displays the manufacturer of the modem REPORT REVISION LEVEL Type: Immediate Format: AT [cmds] #REV? [cmds] Description: Displays the revision number of the modem RINGBACK GOES AWAY TIMER - ORIGINATE MODE Type Configuration Format AT [cmds] #VRA= n [cmds] Default 70 Range 0-255 Unit .01 second Description Sets Ringback Goes Away timer; If ringback is not detected, the modem assumes that the remote has picked up the line and switches to on-line voice command Mode. #VRA=0, will disabled timer. RINGBACK NEVER CAME TIMER - ORIGINATE Type Configuration Format AT [cmds] #VRN= n [cmds] Default 100 Range 0-255 Unit .01 second Description Sets the "Ringback Never Came" timer; If ringback is not detected, the modem assumes the remote has picked up the line and switches to on-line voice command Mode. SAMPLING RATE Type: Configuration Format: AT [cmds] #VSR= n [cmds] Description: Controls DTE interface speed to transmit/receive in voice/audio mode. Command Function » #VSR=7200 7200Hz sampling rate enabled #VSR=11025 11.025Khz sampling rate enabled SILENCE DELETION - VOICE RECEIVE Type: Configuration Format: AT [cmds] #VSD= n [cmds] Description: Controls silence deletion Command Function #VSD=0 Silence deletion disabled #VSD=1 Silence deletion enabled SILENCE DETECTION TIMER - VOICE RECEIVE Type Configuration Format AT [cmds] #VSP= n [cmds] Default 55 Range 0-255 Unit .1 second Description Sets the length of time that the modem does not receive information before it disconnects, while in voice receive mode. SILENCE DETECTION TUNER - VOICE RECEIVE Type: Configuration Format: AT [cmds] #VSS= n [cmds] Description: Controls the sensitivity used by the modem in ADPCM compressing periods of silence. Command Function » #VSS=0 Silence detection disabled #VSS=1 Low sensitive setting enabled #VSS=2 Midrange sensitive setting enabled #VSS=3 High sensitive setting enabled SLEEP TIMER Format AT [cmds] S24= n [cmds] Default: 0 Range: 0-255 Unit: 1 second Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. TEST MODES Format AT [cmds] S16= n [cmds] Default: Unidentified Range: 0-125 Unit: Bit-mapped Description: Controls loopback tests, analog, digital, remote digital, and self tests. Bit Value Function 0 0 Local analog loopback not in progress 1 Local analog loopback in progress 1 0 Not used 2 0 Local digital loopback not in progress 1 Local digital loopback in progress 3 0 Modem not in remote digital loopback 1 Remote digital loopback in progress 4 0 Remote digital loopback not requested 1 Remote digital loopback requested 5 0 Remote digital loopback w/ self-test not in 1 progress Remote digital loopback w/ self-test in progress 6 0 Local analog loopback w/ self-test not in 1 progress Local analog loopback w/ self-test in progress TEST MODE - PTT Type: Configuration Format: AT [cmds] %TT nn [cmds] Description: Send PTT test signal for line test TIMING MARK PLACEMENT Type: Configuration Format: AT [cmds] #VTM= n [cmds] Description: Controls the placement of timing marks by the DCE in the data stream during ADPCM recording. Command Function » #VTM=0 Timing mark placement disabled #VTM=10 Placement of 1 second intervals enabled TRANSMISSION LEVEL Type: Configuration Format: AT [cmds] @M n [cmds] Default: Unidentified Range: 11-31 Unit: -1 dBm Description: Sets the signal level for transmission Command Function @M0 -26dBm @M1 -30dBm @M2-@M10 -10dBm TRANSMISSION LEVEL - FAX Type: Register Format: AT [cmds] S92= n [cmds] Default: 10 Range: 0-15 Unit: -1 dBm Description: Sets the signal level for transmission while in fax mode TRANSMISSION LEVEL - PSTN Type Register Format AT [cmds] S91 =n [cmds] Default 10 Range 1-15 Unit -1 dBm Description Sets the signal level for transmission over switched phone lines VOICE LINE SELECT Type: Configuration Format: AT [cmds] #VLS= n [cmds] Description: Selects which device is routed through the modem Command Function » #VLS=0 Telephone line interface is routed through the modem #VLS=1 The handset is routed through the modem #VLS=2 The speaker is routed through the modem #VLS=3 Auxiliary input device (microphone) is routed through the modem #VLS=4 Telephone line interface and internal speaker are routed through the modem VOICE LINE SELECT - DEVICE TYPE Type: Response Format: AT [cmds] #VLS=? [cmds] Description: Reports back which device type is available for selection Response Function » 0 Telephone Line with handset 1 Handset, headset, or speaker-phone powered directly by the modem 2 Onboard speaker 3 Microphone 4 Telephone line with speaker ON and handset VOICE RECEIVE Type Immediate Format AT [cmds] #VRX [cmds] Description Sets the modem to voice receive mode. VOICE TRANSMIT - ONLINE VOICE COMMAND MODE Type: Configuration Format: AT [cmds] #VTX [cmds] Description: Controls when a voice file is to be transmitted to the line, speaker, or handset; then switches to voice transmit mode V.32 - COMPROMISE EQUALIZER Type: Configuration Format: AT [cmds] :E n [cmds] Description: Controls V.32 compromise equalizer Command Function :E0 Equalizer disabled :E1 Equalizer enabled