CMD TECHNOLOGY, INC. CSA-6222 Card Type Hard drive controller Hard Drives supported Four IDE (AT) drives Floppy drives supported Two 360KB, 720KB, 1.2MB, or 1.44MB drives Data Bus 32-bit VESA Local Bus Card Size Three-quarter length, half-height [Image] CONNECTIONS Function Label Function Label 25-pin parallel port CN1 34-pin cable connector J4 - floppy drive 9-pin serial port - CN2 16-pin game port J5 external 40-pin primary IDE(AT) J1 10-pin serial port 2 - J6 connector internal 2-pin connector - drive J2 10-pin serial port 1 - J7 active LED internal 40-pin secondary J3 IDE(AT) connector USER CONFIGURABLE SETTINGS Function Label Position » Primary IDE base address is 1F0h JP1/A Open Primary VLB-IDE base address is JP1/A Closed 170h » Port address is 78h/7Ch JP1/B Open Port address is 178h/17Ch JP1/B Closed » Factory configured - do not alter JP1/C Open » Primary IDE interface enabled JP1/E Open Primary IDE interface disabled JP1/E Closed » Game port enabled JP3 Closed Game port disabled JP3 Open » Primary IDE interface IRQ 14 JP6/D Closed enabled Primary IDE interface IRQ 14 JP6/D Open disabled DMA CHANNEL SELECTION Channel JP7/D JP7/E » 1 Pins 1 & 2 closed Pins 1 & 2 closed 3 Pins 2 & 3 closed Pins 2 & 3 closed PARALLEL PORT ADDRESS SELECTION Setting JP2/E JP2/F » LPT1 (378h) Pins 1 & 2 closed Pins 2 & 3 closed LPT2 (278h) Pins 1 & 2 closed Pins 1 & 2 closed LPT3 (3BCh) Pins 2 & 3 closed Pins 1 & 2 closed Disabled Pins 2 & 3 closed Pins 2 & 3 closed SERIAL PORT 1 ADDRESS SELECTION Setting JP5/A JP5/B » COM1 (3F8h) Pins 1 & 2 closed Pins 1 & 2 closed COM2 (2F8h) Pins 1 & 2 closed Pins 2 & 3 closed COM3 (3E8h) Pins 2 & 3 closed Pins 1 & 2 closed Disabled Pins 2 & 3 closed Pins 2 & 3 closed SERIAL PORT 2 ADDRESS SELECTION Setting JP5/C JP5/D COM1 (3F8h) Pins 1 & 2 closed Pins 2 & 3 closed » COM2 (2F8h) Pins 1 & 2 closed Pins 1 & 2 closed COM4 (2E8h) Pins 2 & 3 closed Pins 1 & 2 closed Disabled Pins 2 & 3 closed Pins 2 & 3 closed SERIAL PORTS INTERRUPT SELECTION COM 1 COM2 JP7/A JP7/B IRQ3 IRQ4 Pins 2 & 3 Pins 1 & 2 closed closed » IRQ4 IRQ3 Pins 1 & 2 Pins 2 & 3 closed closed PARALLEL PORT INTERRUPT SELECTION Setting JP7/C IRQ5 Pins 1 & 2 closed » IRQ7 Pins 2 & 3 closed PARALLEL PORT MODE SELECTION Setting JP2/C JP2/D » Printer Pins 2 & 3 closed Pins 2 & 3 closed EPP Pins 2 & 3 closed Pins 1 & 2 closed ECP Pins 1 & 2 closed Pins 2 & 3 closed EPP/ECP Pins 1 & 2 closed Pins 1 & 2 closed SECONDARY IDE ADDRESS SELECTION Setting JP2/A JP2/ B 1F0h Pins 1 & 2 closed Pins 2 & 3 closed » 170h Pins 1 & 2 closed Pins 1 & 2 closed Disabled Pins 2 & 3 closed Pins 2 & 3 closed FLOPPY DRIVE CONFIGURATION Setting JP1/D JP5/E JP5/F » Enabled/Primary base Closed Pins 1 & 2 Pins 2 & 3 address is 3F0 closed closed Disabled Open Pins 2 & 3 Pins 2 & 3 closed closed Disabled Open Pins 2 & 3 Pins 1 & 2 closed closed SECONDARY IDE INTERRUPT SELECTION Setting JP6/A JP6/B JP6/C IRQ10 Open Closed Open IRQ14 Open Open Closed » IRQ15 Closed Open Open