PROMISE TECHNOLOGY, INC.

EIDEPRO

Data Bus                16-bit ISA
Card Size               Half-length, full-height card
Hard Drives supported   Four EIDE drives
Floppy drives supported Two 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB drives


[Image]

                                CONNECTIONS

        Function           Location          Function           Location

  9-pin serial port 1 -      CN1      34-pin cable connector       J3
  external                            - floppy drive

  25-pin parallel port -     CN2      16-pin game port             J4
  external

  40-pin primary IDE(AT)      J1      10-pin serial port 2 -       J5
  connector                           internal

  40-pin secondary            J2      4-pin connector -            J6
  IDE(AT) connector                   drive active LED

                        USER CONFIGURABLE SETTINGS

               Function                     Label            Position

  »   Game port enabled                      JP2            Pins 1 & 2
                                                              closed

      Game port disabled                     JP2            Pins 2 & 3
                                                              closed

  »   Parallel port I/O address is           JP3           Pins 13 & 14
      378h                                                    closed

      Parallel port I/O address is           JP3           Pins 14 & 15
      278h                                                    closed

  »   Parallel port IRQ 7 select             JP3           Pins 16 & 17
                                                              closed

      Parallel port IRQ 5 select             JP3           Pins 17 & 18
                                                              closed

  »   Factory configured - do not       JP4/pins 7 & 8        Closed
      alter

  »   Factory configured - do not       JP4/pins 10 &         Closed
      alter                                  11

                              BIOS SELECTION

              Type                                 JP2

  »            C8000h             Pins 10 & 11, 13 & 14, 16 & 17 closed

               CC000h             Pins 10 & 11, 14 & 15, 16 & 17 closed

               D8000h             Pins 10 & 11, 13 & 14, 17 & 18 closed

               DC000h             Pins 10 & 11, 14 & 15, 17 & 18 closed

              Disabled            Pins 11 & 12, 14 & 15, 17 & 18 closed

                           DMA CHANNEL SELECTION

          Channel                                JP5

                1                      Pins 1 & 2, 4 & 5 closed

  »             3                      Pins 2 & 3, 5 & 6 closed

                 SERIAL PORT 1 ADDRESS SELECTION

       Setting                            JP3

  COM1 (3F8h) / IRQ4           Pins 1 & 2, 4 & 5 closed

  COM3 (3E8h) / IRQ4           Pins 2 & 3, 4 & 5 closed

       Disabled                Pins 2 & 3, 5 & 6 closed

                 SERIAL PORT 2 ADDRESS SELECTION

       Setting                            JP3

  COM2 (2F8h) / IRQ3          Pins 7 & 8, 10 & 11 closed

  COM4 (2E8h) / IRQ3          Pins 8 & 9, 10 & 11 closed

       Disabled               Pins 8 & 9, 11 & 12 closed

                     PRIMARY IDE CONTROLLER SELECTION

             Setting                     JP1                 JP2

  »   Primary IDE interface           Pins 4 & 5      Pins 7 & 8 closed
      enabled                          closed

      Primary IDE interface           Pins 4 & 5      Pins 8 & 9 closed
      disabled                          open

                    SECONDARY IDE CONTROLLER SELECTION

             Setting                     JP1                 JP2

  »   Secondary IDE interface         Pins 2 & 3      Pins 4 & 5 closed
      enabled                          closed

      Secondary IDE interface         Pins 2 & 3      Pins 5 & 6 closed
      disabled                          open

                        FLOPPY CONTROLLER SELECTION

            Setting                                JP4

  »           Enabled                  Pins 13 & 14, 16 & 17 closed

              Disabled                 Pins 14 & 15, 17 & 18 closed

                       PARALLEL PORT MODE SELECTION

              Setting                                 JP4

             Uni-directional               Pins 1 & 2, 5 & 6 closed

  »                ECP                     Pins 1 & 2, 4 & 5 closed

                   EPP                     Pins 2 & 3, 5 & 6 closed

                 Disable                   Pins 2 & 3, 4 & 5 closed