KOUWELL ELECTRONICS CORPORATION KW-559AH Data bus: 32-bit VL-bus Size: Three-quarter length, half-height card Hard drive supported: Two IDE(AT) drives Floppy drives supported: Two 360KB, 720KB, 1.2MB, or 1.44MB drives [Image] CONNECTIONS Function Location 40-pin IDE(AT) connector CN1 34-pin cable connector - floppy drive CN2 16-pin game port CN3 10-pin serial port 2 - internal CN4 10-pin serial port 1 - internal CN5 25-pin parallel port - external CN6 4-pin connector - drive active LED JP1 USER CONFIGURABLE SETTINGS Function Location Setting » Parallel port IRQ 7 select JP3/G Pins 2 & 3 closed Parallel port IRQ 5 select JP3/G Pins 1 & 2 closed » Floppy drive interface enabled JP3/H Pins 1 & 2 closed Floppy drive interface disabled JP3/H Pins 2 & 3 closed » Parallel port is bi-directional JP4 Open Parallel port is JP4 Closed uni-directional PARALLEL PORT ADDRESS SELECTION LPT JP3/E JP3/F » LPT1 (378h) Pins 1 & 2 closed Pins 2 & 3 closed LPT2 (278h) Pins 2 & 3 closed Pins 1 & 2 closed LPT3 (3BCh) Pins 1 & 2 closed Pins 1 & 2 closed Disabled Pins 2 & 3 closed Pins 2 & 3 closed SERIAL PORT 1 ADDRESS SELECTION COM JP3/A JP3/B » COM1 (3F8h) Pins 1 & 2 closed Pins 2 & 3 closed COM3 (3E8h) Pins 2 & 3 closed Pins 1 & 2 closed COM4 (2E8h) Pins 1 & 2 closed Pins 1 & 2 closed Disabled Pins 2 & 3 closed Pins 2 & 3 closed SERIAL PORT 2 ADDRESS SELECTION COM JP3/C JP3/D » COM2 (2F8h) Pins 1 & 2 closed Pins 2 & 3 closed COM3 (3E8h) Pins 1 & 2 closed Pins 1 & 2 closed COM4 (2E8h) Pins 2 & 3 closed Pins 1 & 2 closed Disabled Pins 2 & 3 closed Pins 2 & 3 closed SERIAL PORT 1 INTERRUPT SELECTION IRQ JP7/A JP7/B JP7/C JP7/D JP7/E IRQ3 2 & 3 Open Open Open Open » IRQ4 Open 2 & 3 Open Open Open IRQ5 Open Open 2 & 3 Open Open IRQ9 Open Open Open 2 & 3 Open IRQ12 Open Open Open Open 2 & 3 Note: Pins designated must be in the closed position. SERIAL PORT 2 INTERRUPT SELECTION IRQ JP7/A JP7/B JP7/C JP7/D JP7/E » IRQ3 1 & 2 Open Open Open Open IRQ4 Open 1 & 2 Open Open Open IRQ5 Open Open 1 & 2 Open Open IRQ9 Open Open Open 1 & 2 Open IRQ12 Open Open Open Open 1 & 2 Note: Pins designated must be in the closed position. IDE DRIVE SPEED SELECTION Setting JP2/A JP2/B Speed 0 / Slow Pins 1 & 2 closed Pins 1 & 2 closed » Speed 2 Pins 2 & 3 closed Pins 1 & 2 closed Speed 4 Pins 1 & 2 closed Pins 2 & 3 closed Speed 6 / Fast Pins 2 & 3 closed Pins 2 & 3 closed GAME PORT SELECTION Setting JP5 JP6 » Enabled Closed Closed Disabled Open Open