PINE TECHNOLOGY

PT-606G

  Data bus:                  16-bit ISA

  Size:                      Half-length, full-height card

  Hard drive supported:      Two IDE(AT) drives

  Floppy drives supported:   Two 360KB, 720KB, 1.2MB, or 1.44MB drives

[Image]

                        CONNECTIONS

                Function                      Location

  16-pin game port                              CN1

  40-pin IDE(AT) connector                      CN2

  34-pin cable connector - floppy drive         CN3

  9-pin serial port 1 - external                CN4

  10-pin serial port 2 - internal               CN5

  25-pin parallel port - external               CN6

  2-pin connector - drive active LED            JP2

                        USER CONFIGURABLE SETTINGS

                Function                    Location          Setting

  »   IDE(AT) interface enabled                J6            pins 2 & 3
                                                              closed

      IDE(AT) interface disabled               J6            pins 1 & 2
                                                              closed

  »   Game port enabled                        J7            pins 1 & 2
                                                              closed

      Game port disabled                       J7            pins 2 & 3
                                                              closed

  »   Floppy drive interface enabled           J9            pins 1 & 2
                                                              closed

      Floppy drive interface disabled          J9            pins 2 & 3
                                                              closed

                  USER CONFIGURABLE SETTINGS (CONTINUED)

                Function                    Location          Setting

  »   Hard drive is installed                 J10            pins 1 & 2
                                                              closed

      Hard drive is not installed             J10            pins 2 & 3
                                                              closed

  »   Secure power source is in use by        JP3             closed
      printer (standard current)

      Low-end power source is in use          JP3              open
      by printer (isolate current)

  Note: The size and significance of jumper JP1 is unidentified.

                      PARALLEL PORT ADDRESS SELECTION

         LPT               Address             J1                J8

  »        LPT1              378h           pins 1 & 2       pins 1 & 2
                                             closed            closed

           LPT2              278h           pins 1 & 2       pins 2 & 3
                                             closed            closed

       Disable LPT1          N/A            pins 2 & 3       pins 1 & 2
                                             closed            closed

       Disable LPT2          N/A            pins 2 & 3       pins 2 & 3
                                             closed            closed

                       SERIAL PORT ADDRESS SELECTION

   Port 1 (CN4)         Port 2       J2        J3        J4         J5
                        (CN5)

  »       COM1          COM2        pins 1    pins 1    pins 1   pins 1 &
                                     & 2       & 2       & 2        2

          COM1          COM4        pins 1    pins 2    pins 1   pins 1 &
                                     & 2       & 3       & 2        2

          COM3          COM2        pins 1    pins 1    pins 2   pins 1 &
                                     & 2       & 2       & 3        2

          COM3          COM4        pins 1    pins 2    pins 2   pins 1 &
                                     & 2       & 3       & 3        2

          COM1        Disabled      pins 2    pins 1    pins 1   pins 1 &
                                     & 3       & 2       & 2        2

          COM3        Disabled      pins 2    pins 2    pins 2   pins 1 &
                                     & 3       & 3       & 3        2

        Disabled        COM2        pins 1    pins 1    pins 1   pins 2 &
                                     & 2       & 2       & 2        3

        Disabled        COM4        pins 1    pins 2    pins 1   pins 2 &
                                     & 2       & 3       & 2        3

        Disabled      Disabled      pins 2    pins 1    pins 2   pins 2 &
                                     & 3       & 2       & 3        3

  Note: Pins designated should be in the closed position.