SIIG, INC.

IDE PROFESSIONAL VL

  Data bus:                32-bit VL-Bus

  Size:                    Three/quarter-length, half-height card

  Hard drive supported:    Four IDE (AT) interface drives

  Floppy drives            Two 360KB, 720KB, 1.2MB, 1.44MB, or 2.88MB
  supported:               drives

[Image]

                               CONNECTIONS

                    Function                             Location

  16-pin game port - internal                              CN1

  34-pin control cable connector - floppy drive            CN2

  40-pin IDE (AT) interface connector                      IDE1

  40-pin IDE (AT) interface connector                      IDE2

  2-pin connector - drive active LED                       LED1

  2-pin connector - drive active LED                       LED2

  25-pin parallel port - external                           P1

  9-pin serial port - external                             SIO1

  10-pin serial port connector - internal                  SIO2

                        USER CONFIGURABLE SETTINGS

              » Function                   Location           Setting

  »   Game port enabled                 JP1/A pins 2 & 3      closed

  »   Game port disabled                JP1/A pins 1 & 2      closed

  »   VL-Bus IDE (AT) interface         JP1/B pins 2 & 3      closed
      enabled

  »   VL-Bus IDE (AT) interface         JP1/B pins 1 & 2      closed
      disabled

  »   ISA-Bus IDE (AT) interface        JP1/C pins 2 & 3      closed
      enabled

  »   ISA-Bus IDE (AT) interface        JP1/C pins 1 & 2      closed
      disabled

  »   Floppy controller enabled         JP1/D pins 2 & 3      closed

  »   Floppy controller disabled        JP1/D pins 1 & 2      closed

  »   Parallel port IRQ7 select         JP2/E pins 2 & 3      closed

  »   Parallel port IRQ5 select         JP2/E pins 1 & 2      closed

                             IDE CONFIGURATION

  » Primary Adapter     JP2/A         JP2/B        JP2/C         JP2/D

  »    VL-Bus IDE     pins 1 & 2    pins 1 & 2   pins 1 & 2   pins 1 & 2

  »      ISA IDE      pins 2 & 3    pins 2 & 3   pins 2 & 3   pins 2 & 3

       Note: These settings do not apply to any IDE adapters that are
       already present in the system, but reflect the secondary settings
       on the IDE Professional VL.

       Pins designated are in the closed position.

                        SERIAL PORT 1 CONFIGURATION

            » COM                    JP1/E                  JP1/F

  »        COM1 (3F8h)         pins 2 & 3 closed      pins 2 & 3 closed

  »        COM2 (2F8h)         pins 2 & 3 closed      pins 1 & 2 closed

  »        COM3 (3E8h)         pins 1 & 2 closed      pins 2 & 3 closed

  »         Disabled           pins 1 & 2 closed      pins 1 & 2 closed

                     SERIAL PORT 1 INTERRUPT SELECTION

   » IRQ     JP2/F   JP2/G    JP2/H    JP2/I    JP2/J    JP2/K     JP2/L

  »    4     open    1 & 2     open     open     open     open     open

  »   2/9    open     open     open    1 & 2     open     open     open

  »    3     1 & 2    open     open     open     open     open     open

  »    5     open     open    1 & 2     open     open     open     open

  »   10     open     open     open     open    1 & 2     open     open

  »   11     open     open     open     open     open    1 & 2     open

  »   12     open     open     open     open     open     open     1 & 2

  Note: Pins designated are in the closed position.

                        SERIAL PORT 2 CONFIGURATION

            » COM                    JP1/G                  JP1/H

  »        COM2 (2F8h)         pins 2 & 3 closed      pins 2 & 3 closed

  »        COM1 (3F8h)         pins 2 & 3 closed      pins 1 & 2 closed

  »        COM4 (2E8h)         pins 1 & 2 closed      pins 2 & 3 closed

  »         Disabled           pins 1 & 2 closed      pins 1 & 2 closed

                     SERIAL PORT 2 INTERRUPT SELECTION

   » IRQ     JP2/F   JP2/G    JP2/H    JP2/I    JP2/J    JP2/K     JP2/L

  »    3     2 & 3    open     open     open     open     open     open

  »   2/9    open     open     open    2 & 3     open     open     open

  »    4     open    2 & 3     open     open     open     open     open

  »    5     open     open    2 & 3     open     open     open     open

  »   10     open     open     open     open    2 & 3     open     open

  »   11     open     open     open     open     open    2 & 3     open

  »   12     open     open     open     open     open     open     2 & 3

  Note: Pins designated are in the closed position.

                        PARALLEL PORT CONFIGURATION

            » LPT                    JP1/I                  JP1/J

  »        LPT1 (378h)         pins 2 & 3 closed      pins 2 & 3 closed

  »        LPT2 (278h)         pins 2 & 3 closed      pins 1 & 2 closed

  »        LPT3 (3BCh)         pins 1 & 2 closed      pins 1 & 2 closed

  »         Disabled           pins 1 & 2 closed      pins 2 & 3 closed

                       PARALLEL PORT MODE SELECTION

              » Mode                      JP1/K               JP1/L

  »        EPP/Bi-directional           pins 2 & 3      pins 2 & 3 closed
                                         closed

  »               ECP                   pins 1 & 2      pins 1 & 2 closed
                                         closed

  »            ECP & EPP                pins 1 & 2      pins 2 & 3 closed
                                         closed

  »               SPP                   pins 2 & 3      pins 1 & 2 closed
                                         closed

                    PARALLEL PORT DMA CHANNEL SELECTION

  » Channel      JP3/A       JP3/B       JP3/C       JP3/D        JP3/E

  »     3       closed      closed       closed       open        open

  »     1       closed       open         open       closed      closed

  Note: DMA channel selection is only in ECP mode.