ELITEGROUP COMPUTER SYSTEMS, INC.

DI-602

  Data bus:                32-bit, VL-Bus

  Size:                    Three/quarter-length, half-height card

  Hard drive supported:    Two IDE (AT) Interface drives

  Floppy drives            Two 360KB, 720KB, 1.2MB, or 1.44MB drives
  supported:

[Image]

                              CONNECTIONS

                    Function                           Location

  40-pin IDE(AT) Interface connector                      J1

  2-pin connector - Drive active LED                      J2

  34-pin control cable connector - floppy drive           J3

  15-pin game port - internal                             J4

  10-pin serial port (COM1/3) - internal                  J5

  10-pin serial port (COM2/4) - internal                  J6

  25-pin parallel port (LPT2/3) - external                J7

                        USER CONFIGURABLE SETTINGS

               Function                    Location           Setting

  »   Floppy drive enabled                   JP6             pins 1 & 2
                                                              closed

      Floppy drive disabled                  JP6             pins 2 & 3
                                                              closed

  »   Game Port (J4) enabled                 JP7             pins 1 & 2
                                                              closed

      Game Port (J4) disabled                JP7             pins 2 & 3
                                                              closed

  »   Parallel port (J7) is set to           JP8             pins 1 & 2
      LPT2                                                    closed

      Parallel port (J7) is set to           JP8             pins 2 & 3
      LPT3                                                    closed

  »   Parallel port (J7) enabled             JP9             pins 1 & 2
                                                              closed

      Parallel port (J7) disabled            JP9             pins 2 & 3
                                                              closed

  »   Serial Port 2 (J6) enabled             JP10            pins 1 & 2
                                                              closed

      Serial Port 2 (J6 disabled             JP10            pins 2 & 3
                                                              closed

  »   Serial Port 2 (J6) is set to           JP11            pins 1 & 2
      COM2                                                    closed

      Serial Port 2 (J6) is set to           JP11            pins 2 & 3
      COM4                                                    closed

  »   Serial Port 1 (J5) is set to           JP12            pins 1 & 2
      COM1                                                    closed

      Serial Port 1 (J5) is set to           JP12            pins 2 & 3
      COM3                                                    closed

  »   Serial Port 1 (J5) enabled             JP13            pins 1 & 2
                                                              closed

      Serial Port 1 (J5) disabled            JP13            pins 2 & 3
                                                              closed

  »   Parallel port (J7) interrupt           JP14            pins 1 & 2
      is IRQ7                                                 closed

      Parallel port (J7) interrupt           JP14            pins 2 & 3
      is IRQ5                                                 closed

  »   Hard drive enabled                     JP17            pins 1 & 2
                                                              closed

      Hard drive disabled                    JP17            pins 2 & 3
                                                              closed

                   I/O PORT ADDRESS SELECT

       Address            Jumper JP3          Jumper JP16

       26h/27h         pins 1 & 2 closed   pins 2 & 3 closed

       2Ah/2Bh         pins 2 & 3 closed   pins 2 & 3 closed

       2Eh/2Fh         pins 1 & 2 closed   pins 1 & 2 closed

       34h/35h         pins 2 & 3 closed   pins 1 & 2 closed

                       MISCELLANEOUS TECHNICAL NOTES

   Jumpers JP1, JP2 and JP15 are factory configured to pins 1 & 2 closed,
                               do not alter.