DIAMOND FLOWER INC. MIO-400KF REV. F Data bus: 16-bit, ISA Size: Half-length, full-height card Hard drives supported: Two IDE (AT) Interface drives Floppy drives supported: Two 360KB, 720KB, 1.2MB, or 1.44MB drives [Image] CABLE CONNECTIONS 4-pin connector-drive active LED CN1 34-pin data cable connector-floppy drive CN2 16-pin connector-game port CN3 10-pin connector-serial port 2 CN4 40-pin AT Interface (IDE) connector-internal CN5 DB-9 male connector-serial port 1 CN6 DB-25 female connector-parallel port CN7 USER CONFIGURABLE SETTINGS Function Location Setting » Hard drive enabled JP3/jumper 8 pins 2 & 3 closed Hard drive disabled JP3/jumper 8 pins 1 & 2 closed » Game port enabled JP3/jumper 9 pins 2 & 3 closed Game port disabled JP3/jumper 9 pins 1 & 2 closed SERIAL PORT SIGNAL STATUS JP1 - SERIAL PORT 1 - JP2 - SERIAL PORT 2 Function Location Setting » DCD (Data Carrier Detect) - Jumper 1 pins 1 & 2 NORMAL closed DCD (Data Carrier Detect) - Jumper 1 pins 2 & 3 FORCED TRUE closed » DSR (Data Set Ready) - NORMAL Jumper 2 pins 1 & 2 closed DSR (Data Set Ready) - FORCED Jumper 2 pins 2 & 3 TRUE closed » CTS (Clear To Send) - NORMAL Jumper 3 pins 1 & 2 closed CTS (Clear To Send) - FORCED Jumper 3 pins 2 & 3 TRUE closed PARALLEL PORT CONFIGURATION LPT JP3/jumper 1 JP3/jumper 2 Disabled pins 1 & 2 closed pins 1 & 2 closed LPT1 on 3BC pins 1 & 2 closed pins 2 & 3 closed LPT3 on 278 pins 2 & 3 closed pins 1 & 2 closed » LPT2 on 378 pins 2 & 3 closed pins 2 & 3 closed SERIAL PORT CONFIGURATION CN6 CN4 JP3/3 JP3/4 JP3/5 JP8/1 JP8/2 » COM1 COM2 pins 2 pins 2 pins 2 pins 1 pins 1 & 3 & 3 & 3 & 2 & 2 COM2 COM3 pins 2 pins 2 pins 1 pins 2 pins 2 & 3 & 3 & 2 & 3 & 3 COM1 COM4 pins 2 pins 2 pins 2 pins 1 pins 2 & 3 & 3 & 3 & 2 & 3 COM3 COM4 pins 2 pins 2 pins 2 pins 2 pins 1 & 3 & 3 & 3 & 3 & 2 COM1 Disabled pins 2 pins 1 pins 2 pins 1 pins 1 & 3 & 2 & 3 & 2 & 2 Disabled COM2 pins 1 pins 2 pins 2 pins 1 pins 1 & 2 & 3 & 3 & 2 & 2 Disabled Disabled pins 1 pins 1 pins 1 pins 1 pins 1 & 2 & 2 & 2 & 2 & 2 Note:Pins designated should be in the closed position. FLOPPY DRIVE CONFIGURATION Drive JP3/jumper 6 JP3/jumper 7 » Floppy drive pins 2 & 3 closed pins 2 & 3 closed enabled Floppy drive pins 1 & 2 closed pins 2 & 3 closed disabled SERIAL PORT CONFIGURATION JUMPERS JP4 - SERIAL PORT 2 - JP5 - SERIAL PORT 1 » Port is DTE (Data Terminal pins 1 & 2, 3 & 4, 5 & 6, 7 & Equipment) 8, 9 & 10 closed Port is DCE (Data Comm. Equipment) pins 1 & 3, 2 & 4, 5 & 7, 6 & 8, 9 & 10 closed SERIAL PORT IRQ JUMPERS - JP9 JUMPERS 1-4 - SERIAL PORT 2 (DEFAULT SETTING = »Í ) JUMPERS 5-8 - SERIAL PORT 1 (DEFAULT SETTING = » ) IRQ Jumper 1/5 Jumper 2/6 Jumper 3/7 Jumper 4/8 IRQ2 closed open open open IRQ5 open closed open open » IRQ4 open open closed open » í IRQ3 open open open closed PARALLEL PORT IRQ IRQ JP9/jumper 11 JP9/jumper 12 » IRQ5 (For LPT3) closed open IRQ7 (For LPT1 or open closed LPT2)