JPN CORPORATION

CA8301E, CA8302E

Data bus:                16-bit, ISA
Size:                    Half-length, full-height card
Hard drive supported:    Two IDE (AT) Interface drives
Floppy drives supported: Two 360KB, 720KB, 1.2MB, or 1.44MB drives
Maximum heads/cyl.:      8 heads and 1024 cylinders
Special Features         Two serial, one game, and one parallel port
                         (Only one serial port on the CA80301E)

[Image]

                                CONNECTIONS

                     Function                             Location

  40-pin IDE (AT) Interface control cable                    CN1
  connector

  34-pin control cable connector-hard drive                  CN2

  9-pin serial port (COM2/4)-internal                        CN3

  9-pin serial port (COM1/3)-internal                        CN4

  15-pin game port - external                                CN5

  25-pin parallel port (LPT1/2) - external                   CN6

  4-pin connector-drive active LED                           CN7

                        USER CONFIGURABLE SETTINGS

             Function                     Location            Setting

  »   Serial port 1 is set for          JP6/jumper1          pins 1 & 2
      COM1                                                     closed

      Serial port 1 is set for          JP6/jumper1          pins 2 & 3
      COM3                                                     closed

  »   Serial port 1 enabled             JP6/jumper 2         pins 1 & 2
                                                               closed

      Serial port 1 disabled            JP6/jumper 2         pins 2 & 3
                                                               closed

  »   Serial port 2 is set for          JP6/jumper 3         pins 1 & 2
      COM2                                                     closed

      Serial port 2 is set for          JP6/jumper 3         pins 2 & 3
      COM4                                                     closed

  »   Serial port 2 enabled             JP6/jumper 4         pins 1 & 2
                                                               closed

      Serial port 2 disabled            JP6/jumper 4         pins 2 & 3
                                                               closed

  »   Parallel port is set for          JP6/jumper 5         pins 1 & 2
      LPT1 (I/O address 378h)                                  closed

      Parallel port is set for          JP6/jumper 5         pins 2 & 3
      LPT2 (I/O address 278h)                                  closed

  »   Parallel port enabled             JP6/jumper 6         pins 1 & 2
                                                               closed

      Parallel port disabled            JP6/jumper 6         pins 2 & 3
                                                               closed

  »   Game port enabled                 JP6/jumper 7         pins 1 & 2
                                                               closed

      Game port disabled                JP6/jumper 7         pins 2 & 3
                                                               closed

  »   Floppy drive enabled              JP6/jumper 8         pins 1 & 2
                                                               closed

      Floppy drive disabled             JP6/jumper 8         pins 2 & 3
                                                               closed

  »   Hard drive enabled                    JP7              pins 1 & 2
                                                               closed

      Hard drive disabled                   JP7              pins 2 & 3
                                                               closed

  »   Parallel port is set for              JP8              pins 2 & 3
      IRQ7                                                     closed

      Parallel port is set for              JP8              pins 1 & 2
      IRQ5                                                     closed

                       SERIAL PORT IRQ JUMPERS - JP9

   IRQ       Jumper 1        Jumper 2        Jumper 3         Jumper 4

            1-2-COM1/3      1-2-COM1/3      1-2-COM1/3       1-2-COM1/3

            2-3-COM2/4      2-3-COM2/4      2-3-COM2/4       2-3-COM2/4

  »   5       closed           open            open             open

      4        open           closed           open             open

      3        open            open           closed            open

      2        open            open            open            closed

                       MISCELLANEOUS TECHNICAL NOTES

  JP9/jumpers 1 to 4 select Interrupt request for serial port 1 & 2. Pins
    1 - 2 apply to serial port 1 (COM1/3) and pins 2 & 3 apply to serial
      port 2 (COM2/4). The factory defaults are JP9/jumper 2/pins 1-2
  "closed" (COM1/3-IRQ4) & JP9/jumper 3 pins 2-3 "closed" (COM2/4-IRQ3).