SILICON VALLEY COMPUTER INC. ADP111V Data bus: 32-bit, VL-bus Size: Full-length, full-height card Hard drive supported: (2) IDE(AT) interface drives, (2) IDE mirror drives, IDE tape drive Floppy drives supported: 360KB, 720KB, 1.2MB, or 1.44MB drives [Image] CONNECTIONS Function Location 9-pin serial port 1 - internal COM1 9-pin serial port 2 - external COM2 15-pin connector - game port GAME1 4-pin connector - Mirror drive active LED J1 4-pin connector - primary drive active LED J2 40-pin connector - IDE mirror drive cable J3 40-pin IDE(AT) interface connector J4 40-pin ISA IDE tape/IDE CD-ROM interface P1 connector 34-pin control cable connector - floppy P2 drive 4-pin connector - IDE tape/IDE CD-ROM drive P3 active LED 25-pin parallel port - external P4 USER CONFIGURABLE SETTINGS Function Location Setting 8051/8031 micro controller is E1 pins 1 & 2, 3 & 4 installed closed 80C51/80C31 micro controller E1 pins 2 & 3 closed is installed » Serial port 2 enabled E3 pins 2 & 3 closed Serial port 2 disabled E3 pins 1 & 2 closed » Parallel port enabled E4 pins 2 & 3 closed Parallel port disabled E4 pins 1 & 2 closed USER CONFIGURABLE SETTINGS(CONTINUED) Function Location Setting » ISA IDE interface enabled E5 pins 2 & 3 closed ISA IDE interface disabled E5 pins 1 & 2 closed » Floppy drive interface enabled E6 pins 2 & 3 closed Floppy drive interface disabled E6 pins 1 & 2 closed » Serial port 2 address 2F8 - E7 pins 2 & 3 2EFh select closed Serial port 2 address 2E8 - E7 pins 1 & 2 2EFh select closed » Serial port 1 address 3F8 - E8 pins 2 & 3 3FFh select closed Serial port 1 address 3E8 - E8 pins 1 & 2 3EFh select closed » Serial port 1 enabled E9 pins 2 & 3 closed Serial port 1 disabled E9 pins 1 & 2 closed » Parallel port address 378 - E10 pins 2 & 3 37Fh select closed Parallel port address 278 - E10 pins 1 & 2 27Fh select closed » Game port enabled E11 & E12 closed Game port disabled E11 & E12 open » ISA IDE tape drive interrupt E13 pins 2 & 3 IRQ15 select closed ISA IDE tape drive interrupt E13 pins 1 & 2 IRQ10 select closed ISA IDE tape drive interrupt E13 pins 4 & 5 IRQ14 select(do not use) closed » VESA IDE interface interrupt E13 pins 5 & 6 IRQ14 select closed VESA IDE interface interrupt E13 pins 6 & 7 IRQ15 select(do not use) closed Factory configured - do not S1/4 N/A alter Factory configured - do not S1/5 N/A alter » External BIOS enabled S1/6 off Internal BIOS enabled S1/6 on » Factory configured - do not S1/7 N/A alter » Factory configured - do not S1/8 N/A alter » Factory configured - do not SW1/4 on alter BASE MEMORY ADDRESS SELECT Address S1/1 S1/2 » CC000h on off D8000h off on DC000h off off Disabled on on BIOS SIZE Size E2 S1/3 » 8KB open on 16KB closed off Note: The manufacturer recommends that the default value of 8KB should not be changed by the user. DATA TRANSFER RATE TABLE CPU Speed/Type Setting 25/DX2-50 MHz 33/DX-66 MHz 50MHz 0 1.67 2.22 3.33 1 2.00 2.66 4.00 2 2.50 3.33 5.00 3 2.94 3.92 5.88 4 3.12 4.60 6.25 5 4.16 5.55 8.33 6 4.54 6.06 9.09 7 6.25 8.33 12.50 DATA TRANSFER RATE SWITCH SETTINGS Setting SW1/1 SW1/2 SW1/3 0 on on on 1 on on off 2 on off on 3 on off off 4 off on on 5 off on off 6 off off on 7 off off off